TechNexion TCK3-APL Manuale utente

3.1 VESA Mounng

TCK3-APL

Quickstart Guide

3 Installaon Instrucons

This secon describes the mounng procedures for TCK series device. The material in the mounng area must provide suﬃcient strength for support of this embedded

box PC.

The TCK3-BSW is compable with the VESA MIS-D Standard 100*100mm hole paern. There are 4 VESA MIS-D (M4) mounng holes on the top side of the device.

M4 screw holes are a depth of 6mm.

3.2 Surface Mounng

There are 4 mounng holes (M5) on the top side of the device required for surface mounng. Four M4 or M5 screws with at least 8mm head-to-p length are required

to secure this device to the surface.

3.3 DIN Mounng

The device can be mounted on a DIN rail by using a DIN-rail bracket. There are two mounng holes (M3) on the rear side of the device required for DIN bracket

mounng (30mm DIN rail standard). Secure the DIN bracket to the back of this device by using two M3 screws with at least 5mm head-to-p length.

INNOVATORS OF TECHNOLOGY

Top view:

2 Dimensions

1 Safety Precauons

Thank you for purchasing a TechNexion TCK series device. This installaon guide will be helpful in the installaon, wiring and inspecon of your TechNexion embedded

fanless box PC. Before using the product, please read this guide to ensure correct use. You should thoroughly understand all safety precauons before proceeding with

the installaon, wiring, and operaon. Place this instrucon sheet in a safe locaon for future reference. The following suggesons will help you.

• Keep the device dry. Precipitaon, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet,

allow it to dry completely.

• Do not use or store the device in dusty or dirty areas. Its parts and electronic components can be damaged.

• Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage baeries, and warp or melt certain plascs.

• Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards.

• Do not aempt to open the device. This product is designed for speciﬁc applicaons and needs to be installed by qualiﬁed personnel.

• Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and ﬁne mechanics.

• Do not paint the device. Paint can clog the parts and prevent proper operaon.

• Unauthorized modiﬁcaons or aachments could damage the device and may violate regulaons governing radio devices.

• Do not touch any internal or exposed parts of the device as electrical shock may result.

• Do not open the device while power is on. Otherwise electrical shock may result.

• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.

• Be sure the venlaon holes are not obstructed during operaon. Otherwise malfuncon may result due to bad venlaon or overheang.

These suggesons apply equally to your device, baery, charger, or any enhancement. If any device is not working properly, take it to the nearest authorized service

facility for service.

•Make sure that the available power source matches the required input power of the device. Failure to observe this cauon may result in electric shock or ﬁre.

•Do not power the unit by DC input when you apply power over the PoE (RJ45).

1.1 Storage and Installaon

1.2 Wiring

1.3 Maintenance and Inspecon

Unit : mm

1 2

187.5

105

129

173.5

106

4.5

62.5

14.5

137.2

50 50

40.2

4 External Connectors

without the prior wrien permission of TechNexion Ltd.

• No warranty of accuracy is given concerning the contents of the informaon contained in this publicaon. To the extent permied by law no liability (including liability to any person by reason of

negligence) will be accepted by TechNexion Ltd., its subsidiaries or employees for any direct or indirect loss or damage caused by omissions from or inaccuracies in this document.

• TechNexion Ltd. reserves the right to change details in this publicaon without noce. Please download the most updated version at: hps://www.technexion.com/support/download-center/

Phone: +886-2-82273585 Web: www.technexion.com

16F-5, No. 736, Zhongzheng Road, ZhongHe District, 23511, New Taipei City, Taiwan

2019-07-02

5.1 Digital I/O Connector (GPIO)

5.2 Serial Ports (RS-XXX1/RS-XXX2)

5 Pin Deﬁnion

6 LED Light Indicators

This product is available with one GPIO connector. The non-galvanic isolated GPIO connector has the following pinout:

The TCK3-APL has two LED Light indicators. The Power LED Light indicator is lit, when the system is powered on. The SATA LED Light indicator is blinking, when the

SATA SSD is acve.

Header on TCK3-APL: DB15 (15-pin) high density D-Sub male connector.

Cable receptacle: DB15 (15-pin) high density D-Sub female connector.

This product is available with two full funcon non-galvanic isolated RS-232 serial ports:

RS-XXX1 and RS-XXX2. The ports have the following pinout:

Description No.No. Description

Power LED indicator

Power Input connector

RS-XXX1 (Serial Port) DB9 connector

LAN1 RJ45 connector

LAN2 RJ45 connector

USB Host connector

miniDP1 connector

miniDP2 connector

SATA LED indicator

Grounding screw M4

Antenna hole

Power button

USB OTG (Type-C) connector

microSD cardslot

RS-XXX2 (Serial Port) DB9 connector

Micro-SIM cardslot

3.5mm audio jack

GPIO DB15 connector

LED# Color

OFF

1 Power on

SATA SSD is active (blinking)

Green

Red

Power off

SATA SSD is not active

GPIO:

RS-XXX1:

INDICATOR:

Front view:

Le view:

31 2 4 579

10 11

16 17 18

Rear view:

Right view:

2423 25 26

12 13 14 15

20 21 22

Port Pin #

Signal

VCC

GPIO1A

GPIO1C

GPIO2A

GPIO2C

GND

VCC

GPIO1B

GPIO1D

GPIO2B

GPIO2D

Description Voltage

Supply output

DIG_IN2/OUT2

DIG_IN4/OUT4

DIG_IN6/OUT6

DIG_IN8/OUT8

Common Ground

Supply output

DIG_IN3/OUT3

DIG_IN5/OUT5

DIG_IN7/OUT7

DIG_IN9/OUT9

3.3V

Header on TCK3-APL: DB9 (9-pin) standard D-Sub male connector.

Cable receptacle: DB9 (9-pin) standard D-Sub female connector.

Header on TCK3-APL: DB9 (9-pin) standard D-Sub male connector.

Cable receptacle: DB9 (9-pin) standard D-Sub female connector.

Port Pin #

Signal

SERIAL1_DCD

SERIAL1_RXD

SERIAL1_TXD

SERIAL1_DTR

GND

SERIAL1_DSR

SERIAL1_RTS

SERIAL1_CTS

VCC

Description Device

Port#1 Data Carrier Detect (input)

Port#1 Receive data (input)

Port#1 Transmit data (output)

Port#1 Data Terminal Ready (output)

Ground

Port#1 Data Set Ready (input)

Port#1 Request-to-send (output)

Port#1 Clear-to-send (input)

5V supply output

COM1

The unit is by default preloaded with soware that can download and install a selecon of Linux OS images over hardwired network. Simply connect a display to the

unit though the miniDP connector and a network through the Ethernet LAN RJ45 connector and power it up, then follow the steps on the screen to load the

soware.Local proxies will interfere with this process. For more informaon, go to our Knowledge Base at: hps://www.technexion.com/support/knowledge-base/

To download drivers for the Windows operang systems, go to our Download Center at:

hps://www.technexion.com/support/download-center/

For more informaon about installing and conﬁguring the Windows operang systems, see: hps://msdn.microso.com/en-us/

7 Soware and Driver Installaon

3 4

6 10

6 9

RS-XXX2:

Port Pin #

Signal

SERIAL2_DCD

SERIAL2_RXD