• All Rights Reserved. No part of this document may be photocopied, reproduced, stored in a retrieval system, or transmied, in any form or by any means whether, electronic, mechanical, or otherwise
without the prior wrien permission of TechNexion Ltd.
• No warranty of accuracy is given concerning the contents of the informaon contained in this publicaon. To the extent permied by law no liability (including liability to any person by reason of
negligence) will be accepted by TechNexion Ltd., its subsidiaries or employees for any direct or indirect loss or damage caused by omissions from or inaccuracies in this document.
• TechNexion Ltd. reserves the right to change details in this publicaon without noce. Please download the most updated version at: hps://www.technexion.com/support/download-center/
Phone: +886-2-82273585 Web: www.technexion.com
16F-5, No. 736, Zhongzheng Road, ZhongHe District, 23511, New Taipei City, Taiwan
© 2001-2019 TechNexion Ltd.
2019-12-03
5.1.1 Digital I/O Connector (GPIO)
5.1.2 Serial Ports (RS-XXX1/RS-XXX2/RS-XXX3/RS-XXX4)
5.2.1 Digital I/O Connector (GPIO)
5.1 Galvanic Isolated Connectors Pin Definion (TEK5-Exxxx-Rxx-x-I-xxx-xxxx-xxxxx-x-xxxx-TI-xxxx) (oponal)
5.2 Non-Galvanic Isolated Connectors Pin Definion (TEK5-Exxxx-Rxx-x-N-xxx-xxxx-xxxxx-x-xxxx-TI-xxxx) (oponal)
5 Pin Definion 6LED Light Indicators
7 Power Input Connector
8 Remote Power Buon Connector
This product is available with one GPIO connector. The galvanic isolated GPIO connector has the following pinout:
This product is available with five connectors: GPIO, RS-XXX1, RS-XXX2, RS-XXX3, and RS-XXX4 that can be ordered in either a
galvanic isolated or non-galvanic isolated version.
This product is available with four full funcon galvanic isolated serial ports.
RS-XXX1/RS-XXX2 are set as RS-232 during manufacturing. For seng details of RS-XXX1/RS-XXX2 serial ports in other modes,
please refer to the TEK5-APL HARDWARE MANUAL. RS-XXX3/RS-XXX4 serial ports can be used as a standard RS-232 only. The
ports have the following pinout:
The TEP5-APL can be powered over the DC INPUT connector. This device can be ordered with (TEK5-Exxxx-Rxx-P-x-xxx
-xxxx-xxxxx-x-xxxx-TI-xxxx) or without (TEK5-Exxxx-Rxx-L-x-xxx-xxxx-xxxxx-x-xxxx-TI-xxxx) a power ignion feature.
Header on TEP5-APL: DINKLE 2EHDRM-03P (3-pin 5.08mm pitch terminal block with threaded flange).
Cable receptacle: DINKLE 2ESDVM-03P (3-pin 5.08mm pitch terminal block connector plug).
Header on TEP5-APL: DINKLE 0225-1602 (2-pin 3.50mm pitch terminal block with threaded flange).
Cable receptacle: DINKLE 0225-0602 (2-pin 3.50mm pitch terminal block connector plug).
TEK5-Exxxx-Rxx-P-x-xxx-xxxx-xxxxx-x-xxxx-TI-xxxx:
TEK5-Exxxx-Rxx-L-x-xxx-xxxx-xxxxx-x-xxxx-TI-xxxx:
This product is available with one GPIO connector. The non-galvanic isolated GPIO connector has the following pinout:
The TEK5-APL has six LED light indicators including four programmable LED Light indicators.
The TEP5-APL features a remote power buon connector.
Header on TEP5-APL: DINKLE 0156-1810L (10-pin 2.54mm pitch terminal block) connector socket.
Cable receptacle: DINKLE 0156-1A10-BK (10-pin 2.54mm pitch terminal block) connector plug.
LED# Color
PCB Location
Registered Address
1 LED-A1
LED-A2
LED-A3
LED-A4
Green
Green
Green
Green
0xF9_BIT4 (SIO)
0xF9_BIT3 (SIO)
0xED_BIT2 (SIO)
0xED_BIT1 (SIO)
2
3
4
LED# Color
ON
OFF
5 Power on
SATA SSD is active (blinking)
Green
Red
Power off
SATA SSD is not active
6
GPIO:
RS-XXX1/RS-XXX2/
RS-XXX3/RS-XXX4:
GPIO:
Port Pin #
Signal
1
2
3
4
5
6
7
8
9
10
GPIO1A
GPIO1B
GPIO1C
GPIO1D
GPIO1E
GPIO1F
GPIO1G
GPIO1H
GND
VCC
Description Voltage
Voltage
DIG_IN1
DIG_OUT1
DIG_IN2
DIG_OUT2
DIG_IN3
DIG_OUT3
DIG_IN4
DIG_OUT4
Common Ground
Supply output
5V
12V
5V
12V
5V
12V
5V
12V
5V
Current Max.
1A
125 mA
1A
125 mA
1A
125 mA
1A
125 mA
300 mA
Header on TEK5-APL: DB9 (9-pin) standard D-Sub male connector.
Cable receptacle: DB9 (9-pin) standard D-Sub female connector.
Header on TEP5-APL: DINKLE 0156-1810L (10-pin 2.54mm pitch terminal block) connector socket.
Cable receptacle: DINKLE 0156-1A10-BK (10-pin 2.54mm pitch terminal block) connector plug.
Port Pin #
Signal
1
2
3
4
5
7
6
8
9
SERIAL1/2/3/4_DCD
SERIAL1/2/3/4_RXD
SERIAL1/2/3/4_TXD
SERIAL1/2/3/4_DTR
GND
SERIAL1/2/3/4_DSR
SERIAL1/2/3/4_RTS
SERIAL1/2/3/4_CTS
VCC*
Description Device
Data Carrier Detect (input)
Receive data (input)
Transmit data (output)
Data Terminal Ready (output)
Ground
Data Set Ready (input)
Request-to-send (output)
Clear-to-send (input)
5V supply output (current max. 500mA)
COM1/2/3/4
COM1/2/3/4
COM1/2/3/4
COM1/2/3/4
COM1/2/3/4
COM1/2/3/4
COM1/2/3/4
The unit is by default preloaded with soware that can download and install a selecon of Linux OS images over hardwired network. Simply connect a display to the
unit though the DP or DVI-D or VGA connector and a network through the Ethernet LAN RJ45 connector and power it up, then follow the steps on the screen to load
the soware. Local proxies will interfere with this process. For more informaon, go to our Knowledge Base at: hps://www.technexion.com/support/knowledge-base/
To download drivers for the Windows operang systems, go to our Download Center at:
hps://www.technexion.com/support/download-center/
For more informaon about installing and configuring the Windows operang systems, see: hps://msdn.microso.com/en-us/
9 Soware and Driver Installaon
3 4
1
6 9
5
Besides, the TEP5-APL features Power LED and SATA LED indicators. The Power LED Light indicator is lit,
when the system is powered on. The SATA LED Light indicator is blinking, when the SATA SSD is acve.
5.2.2 Serial Ports (RS-XXX1/RS-XXX2/RS-XXX3/RS-XXX4)
RS-XXX1/RS-XXX2 are set as RS-232 during manufacturing. For seng details of RS-XXX1/RS-XXX2 serial ports in other modes,
please refer to the TEK5-APL HARDWARE MANUAL. RS-XXX3/RS-XXX4 serial ports can be used as a standard RS-232 only. The
ports have the following pinout:
This product is available with four full funcon non-galvanic isolated serial ports.
RS-XXX1/RS-XXX2/
RS-XXX3/RS-XXX4:
Header on TEK5-APL: DB9 (9-pin) standard D-Sub male connector.
Cable receptacle: DB9 (9-pin) standard D-Sub female connector.
Port Pin #
Signal
1
2
3
4
5
7
6
8
9
SERIAL1/2/3/4_DCD
SERIAL1/2/3/4_RXD
SERIAL1/2/3/4_TXD
SERIAL1/2/3/4_DTR
GND
SERIAL1/2/3/4_DSR
SERIAL1/2/3/4_RTS
SERIAL1/2/3/4_CTS
VCC*
Description Device
Data Carrier Detect (input)
Receive data (input)
Transmit data (output)
Data Terminal Ready (output)
Ground
Data Set Ready (input)
Request-to-send (output)
Clear-to-send (input)
5V supply output (current max. 500mA)
COM1/2/3/4
COM1/2/3/4
COM1/2/3/4
COM1/2/3/4
COM1/2/3/4
COM1/2/3/4
COM1/2/3/4
1
6 9
5
Port Pin #
Signal
1
2
3
4
5
7
6
8
9
10
GPIO1A
GPIO1B
GPIO1C
GPIO1D
GPIO1E
GPIO1F
GPIO1G
GPIO1H
GND
VCC
Description Current Max.
DIG_IN1
DIG_OUT2
DIG_IN3
DIG_OUT4
DIG_IN5
DIG_OUT6
DIG_IN7
DIG_OUT8
Common Ground
Supply output
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
3.3V
5V
12 mA
12 mA
12 mA
12 mA
12 mA
12 mA
12 mA
12 mA
300 mA
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
Connector Pin #
Signal
1
2
3
VCC
GND
IGN
Description
DC Voltage input (8~36VDC)
Ground
Signal from MCU
1 32
Connector Pin #
Signal
1
2
3
VCC
GND
NC
Description
DC Voltage input (8~36VDC)
Ground
1 32
Connector Pin #
Signal
1
2
PWRON
GND
Description
Switch power source
Ground
1 2
