TechniSat DigiCorder S1 Manuale utente
Beokompatible functions
OneRemote Interface type 2965
Technisat DigiCorder S1, S2, HD S2 Plus
Beo4 and Beolink 1000 are remote control terminals from Bang & Olufsen. OneRemote supplies interface
modules that allow third party equipment to be operated via a Bang & Olufsen remote control system.
Made in Denmark by www.oneremote.dk
Congratulations
With the EXT interface module from www. oneremote.dk connected to your receiver and
a Bang & Olufsen TV you can operate your receiver with your Bang & Olufsen remote
control terminal. This user guide tells you how.
Plug & Play
The TV-scart output on the receiver can be connected directly to a vacant link equipped
AV socket on the Bang & Olufsen TV with the special EXT scart connection cable.
Connected in this way, the receiver can be used with any Bang & Olufsen TV, serving the
TV with RGB signals and audio through the same cable.
Following the correct programming of the AV connection the receiver is ready to operate.
For programming of the AV connection, check the Bang & Olufsen TV User Manual.
If both the receiver and the TV are equipped with a HDMI socket, use this connection for
improved picture and sound quality.
Bang & Olufsen remote controls
With your beocompatible* receiver connected to a Bang & Olufsen TV you may operate
it with a Bang & Olufsen Beo4 or Beo5 remote control.
Operation in a Beolink Videosystem
In a Bang & Olufsen Beolink Videosystem full operability is ensured in all link rooms, via
this solution.
Operating with Beo4 or Beo5
Beo4 does not have as many keys as the receiver’s original remote control. Thus certain
Beo4 keys have got alternative functionality. To get to this Ohas to be pressed first, i.e.
Ofollowed by 9on a Beo4 corresponds to power on the original remote control.
The table on page 4 shows how special Beo4 key operations translate to operations of the
original remote control.
To be able to operate the receiver correctly with the Beo4 the user has to be familiar with
operations with the original remote control as described in the receiver’s user manual.
The receiver is automatically turned on when selecting its source on the TV.
*Beocompatible means that the equipment can be operated with a Bang & Olufsen remote control when
connected to a Bang & Olufsen TV.
Installation – options.
The EXT controller can be programmed with different options, for use in different setups.
Programming of an option is usually done when installing the controller, not during daily
use. To programme an option, 5 keys must be pressed within 2 seconds.
Available options:
Menu button option.
Some B&O TV catches the Menu button, before the command is echoed out via the scart
connector to the EXT controller. This gives a conflict as the TV’s menu is then being
displayed instead of the receivers menu. In these cases the direct menu button should be
deactivated.
eOr80 Deactivate Menu
eOr81 Activate Menu
Power off option.
The receiver can power off when the TV is powered off. If the receiver is used in a setup
with link rooms or recorders, this might not be practical.
This option can deactivate automatic power off.
eOr70 Deactivate Poff
eOr71 Activate Poff
Programme Zapping option
The yellow and blue buttons are being used as programme zapping buttons. In this waythe
up, down, left and right buttons are available in all menus as well as the pro-gramme
zapping buttons.
This is the OneRemote layout and compa-tible with other OneRemote controllers.
Some people might prefer to have the programme zapping buttons on the up and down
buttons.
This option exchanges the functions of the blue/ yellow and the up/ down buttons.
eOr91 Coloured
eOr90 Up/ down
Daily use.
OO OK
Q*2 SFI/ EPG
E*2 Exit
W*1,*2 P+
R*1,*2 P-
o1 TV/ Radio
*1 The yellow and blue buttons are being used as
programme zapping buttons. In this way the up, down,
left and right buttons are directly available in all
menus as well as the programme zapping buttons.
This is the OneRemote layout and compatible with
other OneRemote controllers.
Some people might prefer to have the programme
zapping buttons on the up and down buttons. To
exchange the functions of the blue/ yellow and the up/
down buttons, see option programming on page 3.
*2 As the coloured buttons has been assigned other
direct functions, a Ohas to be pressed first, to get
the coloured operation.
OQcorresponds to the green function on the
receivers remote control.
Recording and playback.
o Play/ pause press 1 sec
qStop
rr Record
o8 Record optional
Special operations
o0 Text
o2 Genre
o3 info
o4 OPT
o5 Menu
o6 PIP
o7 Sound
o9 Power
oe HDMI
2965u5uk
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali TechniSat Ricevitore
TechniSat
TechniSat DigitMod S1 Manuale utente
TechniSat
TechniSat HDFV Manuale utente
TechniSat
TechniSat SkyStar USB HD Manuale utente
TechniSat
TechniSat EUROKLASSIK 1 Manuale utente
TechniSat
TechniSat DIGIT ISIO STC Manuale di istruzioni
TechniSat
TechniSat HDFS Manuale utente
TechniSat
TechniSat DigiPal1 Manuale utente
TechniSat
TechniSat DigiPlus STR 1 Manuale utente
TechniSat
TechniSat VC 2002 S Istruzioni operative
TechniSat
TechniSat HD-S 261 Manuale utente
TechniSat
TechniSat DigiPal 2 Manuale utente
TechniSat
TechniSat DIGITY 1 Manuale utente
TechniSat
TechniSat HDFS Manuale utente
TechniSat
TechniSat DigiCorder Manuale
TechniSat
TechniSat TechniBox VIACAM Manuale utente
TechniSat
TechniSat DigiPal 1 Manuale utente
TechniSat
TechniSat DigiCorder S2 Manuale utente
TechniSat
TechniSat DIGITRADIO 1980 Manuale utente
TechniSat
TechniSat VIACCESS DigiBox VIACCESS Manuale utente
TechniSat
TechniSat 0010/4770 Manuale utente
