Technische Alternative RAS PLUS DL Manuale utente

www.ta.co.at

English

RAS+DL

Room sensor with remote display

Version 2.03

Operation

Programming

Installation Instructions

Table of Contents

Version 2.03

Function description...........................................................................................4

Programming manual.........................................................................................5

Menu –general overviews ..................................................................................................6

Menu overview UVR16x2, RSM610, CAN-I/O45 and UVR1611.........................................6

Menu overview for ESR21 (from version 5.0) and ESR31, UVR61-3 (from version 8.3),

UVR63 (from version 1.5) ................................................................................................7

Menu overview for all other controllers ...........................................................................8

Menu CONFIG......................................................................................................................9

Language selection SPR DE/LAN EN...............................................................................9

Time interval for continuing display TIME N ....................................................................9

Time before jumping back to the 1st display TIME B.....................................................10

Address in the DL-bus network DL ADR.........................................................................10

Index specification ........................................................................................................11

Entry of an offset value for sensor correction OFFSET..................................................12

Display of operating mode symbols SYMB....................................................................13

Menu VALUES ...................................................................................................................14

Menu sensor values SENSOR ........................................................................................14

Menu speed stages SPEED (only UVR1611)..................................................................16

Menu heat quantity counter POWER..............................................................................17

Menu external sensors NETW (only ESR21 (from version 5.0), ESR31, UVR61-3 (from

version 8.3), UVR63 (from version 1.5)).........................................................................18

Menu analogue CAN network inputs ANALNW (only UVR1611)....................................19

Menu digital CAN network inputs DIGINW (only UVR1611) ...........................................20

Menu symbol allocation SYMB......................................................................................21

Deleting or changing a symbol allocation:.....................................................................23

Reset to factory setting.....................................................................................................24

Operation ..........................................................................................................25

Room sensor with UVR16x2, RSM610, CAN-I/O45, UVR1611(from vers. A3.00 and serial

number 13286) or with UVR63-H (from vers. 7.2) ............................................................25

Use as a remote control ....................................................................................................26

Room sensors with other controllers ................................................................................26

Installation........................................................................................................26

Electrical connections.......................................................................................................27

Technical data ..................................................................................................27

Function description

The room sensor RAS+DL was specially developed for Technical Alternative control units and

is intended for mounting in the living area (reference space). The room sensor should not be

installed near a source of heat or near a window. It is only suitable for operation in dry rooms.

The RAS+DL transmits the room temperature, relative room humidity, ambient air pressure,

absolute humidity and the dew point as well as the operating mode and the correction factor

for the set value (+/- 4 K) to the controller via the bidirectional data link (DL-bus). Using the

DL-bus it is also possible to display controller sensor values, output states, heat quantity

counter outputs and network inputs at the RAS+DL (remote display). Programming of the

sensor permits the setting of which values and symbols are to be output to the display.

Moreover, there is a choice between automatic or manual scrolling between the displays.

The sensor RAS+DL can be used with the following controllers as a room sensor with remote

display:

UVR 16x2

RSM 610

CAN-I/O 45

UVR 1611 from version A3.00 and serial number 13286

UVR 63-H from version 7.2

UVR 63 from version 1.0

UVR 61-3 from version 5.0

ESR 31 from version 1.0

ESR 21 from version 5.0

Moreover, the RAS+DL can also be used with the following controllers as a remote display

device (without sensor functions):

UVR 31

UVR 42

UVR 64

HZR 65

UVR 1611 < version A3.00

UVR 63-H < version 5.0

UVR 61-3 < version 5.0

ESR 21 < version 5.0

These controllers do not have a bidirectional data link.

Programming manual

Only the basic values are displayed in the factory settings of the room sensor:

Room temperature

Relative Room humidity

Ambient air pressure

Dewpoint

Nominal value adjustment (+/- 4K)

With the aid of programming, other values can be displayed.

Access to the programming level is only possible from the "Standby" position (leftmost) of

the slider switch.

RAS+DL can be configured using the key and set up to display further values.

The following symbols are used in the menu descriptions to differentiate between long and

short key presses:

Long key press (at least 2 seconds)

Short key press

Multiple short key presses

Further information about the menu views:

Red printed numbers or symbols mean that they flash in the display.

Exiting from a menu level is always only possible from the "EXIT" display

indication via a long key press.

Menu –general overviews

The displayed menu options are matched to the respective controller types:

Menu overview UVR16x2, RSM610, CAN-I/O45 and UVR1611

In the menu section "CONFIG" gen-

eral sensor settings are adjusted.

The selection of the values and sym-

bols to be displayed takes place in

the menu section "VALUES".

V 1 10 = Sensor version number

Menu overview for ESR21 (from version 5.0) and ESR31, UVR61-3

(from version 8.3), UVR63 (from version 1.5)

In the menu section "CONFIG" gen-

eral sensor settings are adjusted.

The selection of the values and sym-

bols to be displayed takes place in

the menu section "VALUES".

V 1 10 = Sensor version number

Menu overview for all other controllers

In the menu section "CONFIG" gen-

eral sensor settings are adjusted.

The selection of the values and sym-

bols to be displayed takes place in

the menu section "VALUES".

The menu option "POWER" (heat

quantity counter) is only displayed

with those controllers that have this

function.

V 1 10 = Sensor version number

Menu CONFIG

The following settings are made here:

Language selection SPR DE / LAN EN

Time interval for continuing display TIME N

Time before jumping back to the 1st display TIME R

Address in the DL-bus network DL ADR

Entry of an offset value for sensor correction OFFSET

Language selection SPR DE/LAN EN

Switching between German (DE) and Eng-

lish (EN)

Factory setting: DE

To activate the language selection the RAS+DL must be initialised by scrolling forward into

the display level.

Time interval for continuing display TIME N

Entry 0 = no automatic forwarding between

the displays

Factory setting: 0

After a long key press "0" flashes

Selection of the desired time via a short key

press.

Confirmation of the desired time via a long

key press.

Entry 15 = The value display scrolls for-

wards every 15 seconds to the next display.

Adjustment range: 0 –99 sec in second

steps

Time before jumping back to the 1st display TIME R

Entry 0 = There is no jumping back to the display

of the 1st value.

Factory setting: 0

After a long key press "0" flashes

Selection of the desired time via a short key press.

Confirmation of the desired time via a long key

press.

Entry 60 = After 60 seconds without pushing of

the button jumping back from one of the addition-

al programmed values to the first display value

(room temperature) occurs. Adjustment range: 0

–200 sec in 1 second steps

The jump back occurs only from the additionally programmed display values, not from one of

the base values.

Note: If the continuing display TIME N is activated (≠0), then TIME R has no effect.

Address in the DL-bus network DL ADR

Upon querying by the controller ESR31, UVR63 (from version 1.0), ESR21, UVR61-3 and

UVR63-H (from version 5.0), UVR1611 (from version A3.00), plus UVR16x2, RSM610 and

CAN-I/O45 the sensor returns the corresponding measured value. The request consists of

the address of the sensor and the index number of a measured value.

Each member of the DL-bus network must have

its own address so that it can send values to a

controller.

Factory setting: DL 1

After a long key press "1" flashes

Selection of the desired address via a short key

press.

Adjustment range: DL 1 to DL 8

Confirmation of the desired address via a long

key press.

Among those controllers that have no bidirectional data link (e.g. HZR65), i.e. those for which

the RAS+DL can only be used as a remote display, this menu option is still displayed but has

no effective function and must therefore not be observed.

Indice

Altri manuali Technische Alternative Accessori

Technische Alternative

Technische Alternative RAS-F Manuale utente

Technische Alternative

Technische Alternative RAS-PLUS Manuale utente

Technische Alternative

Technische Alternative RAS+DL Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente