Technische Alternative RAS-PLUS Manuale utente
RAS-PLUS (/F)
Version 1.10 EN
Room sensor
with remote display
RAS-PLUS = Room sensor with
temperature measurement and remote
display
RAS-PLUS/F = Room sensor with
temperature and humidity measure-
ment and remote display
Operation
Programming
Installation instructions
en
Table of Contents
Function description ........................................................................................4
Programming manual.......................................................................................5
Menu – general overviews................................................................................................6
Menu overview UVR16x2, RSM610, CAN-I/O45 and UVR1611.....................................6
Menu overview for ESR21 (from version 5.0) and ESR31, UVR61-3 (from version 8.3),
UVR63 (from version 1.5)................................................................................................7
Menu overview for all other controllers............................................................................8
Menu CONFIG....................................................................................................................9
Language selection SPR DE/LAN EN.............................................................................9
Time interval for continuing display TIME N....................................................................9
Time before jumping back to the 1st display TIME B ....................................................10
Address in the DL-bus network DL ADR .......................................................................11
Index specification.........................................................................................................12
Entry of an offset value for sensor correction OFFSET.................................................13
Display of operating mode symbols SYMB ...................................................................14
Menu VALUES..................................................................................................................15
Menu sensor values SENSOR......................................................................................15
Menu output statuses OUTPUT ....................................................................................16
Menu speed stages SPEED (only UVR1611) ...............................................................17
Menu heat quantity counter POWER ............................................................................18
Menu external sensors NETW (only ESR21 (from version 5.0), ESR31, UVR61-3 (from
version 8.3), UVR63 (from version 1.5))........................................................................19
Menu analog CAN network inputs ANALNW (only UVR1611) ......................................20
Menu digital CAN network inputs DIGINW (only UVR1611)..........................................21
Menu symbol allocation SYMB......................................................................................22
Deleting or changing a symbol allocation:.....................................................................24
Reset to factory setting...................................................................................................25
Operation.........................................................................................................26
Room sensor with UVR16x2, RSM610, CAN-I/O45, UVR1611(from vers. A3.00 and
serial number 13286) or with UVR63-H(from vers. 7.2) ................................................26
Use as a remote control..................................................................................................27
Room sensors with other controllers............................................................................27
Installation.......................................................................................................27
Electrical connections ....................................................................................................27
Technical data.................................................................................................27
4
Function description
The room sensor RAS-PLUS was specially developed for Technical Alternative control
units and is intended for mounting in the living area (reference space). The room sensor
should not be installed near a source of heat or near a window. It is only suitable for opera-
tion in dry rooms.
The RAS-PLUS transmits the room temperature, relative room humidity (only RAS-PLUS/F)
and the dew point (only RAS-PLUS/F), the operating mode and the correction value for the
nominal value (+/- 5K) to the controller via the bidirectional data link (DL-bus). Using the DL-
bus it is also possible to display controller sensor values, output states, heat quantity counter
outputs and network inputs at the RAS-PLUS (remote display). Programming of the sensor
permits the setting of which values and symbols are to be output to the display. Moreover
there is a choice between automatic or manual scrolling between the displays.
The sensor RAS-PLUS can be used with the following controllers as a room sensor with
remote display:
UVR 16x2
RSM 610
CAN-I/O 45
UVR 1611 from version A3.00 and serial number13286
UVR 63-H from version 7.2
UVR 63 from version 1.0
UVR 61-3 from version 5.0
ESR 31 from version 1.0
ESR 21 from version 5.0
Moreover the RAS-PLUS can also be used with the following controllers as a remote dis-
play device (without sensor functions):
UVR 31
UVR 42
UVR 64
HZR 65
UVR 1611 < version A3.00
UVR 63-H < version 5.0
UVR 61-3 < version 5.0
ESR 21 < version 5.0
These controllers do not have a bidirectional data link.
5
Programming manual
Only the basic values are displayed in the factory setting of the room sensor:
Room temperature
Relative Room humidity (only RAS-PLUS/F)
Nominal value adjustment (+/- 5K)
With the aid of programming other values can be displayed.
Access to the programming level is only possible from the "Standby" position
(extreme left) of the slider switch.
RAS-PLUS can be configured using the key and set up to display further values.
The following symbols are used in the menu descriptions to differentiate between long and
short key presses:
Long key press (at least 2 seconds)
Short key press
Multiple short key presses
Further information about the menu views:
Red printed numbers or symbols mean that they flash in the display.
Exiting from a menu level is always only possible from the "EXIT" display
indication by a long key press.
6
Menu – general overviews
The displayed menu options are matched to the respective controller types:
Menu overview UVR16x2, RSM610, CAN-I/O45 and UVR1611
In the menu section "CONFIG" gen-
eral sensor settings are adjusted.
The selection of the values and sym-
bols to be displayed takes place in
the menu section "VALUES".
V 1 10 = Sensor version number
7
Menu overview for ESR21 (from version 5.0) and ESR31, UVR61-
3 (from version 8.3), UVR63 (from version 1.5)
In the menu section "CONFIG" gen-
eral sensor settings are adjusted.
The selection of the values and sym-
bols to be displayed takes place in
the menu section "VALUES".
V 1 10 = Sensor version number
8
Menu overview for all other controllers
In the menu section "CONFIG" gen-
eral sensor settings are adjusted.
The selection of the values and sym-
bols to be displayed takes place in
the menu section "VALUES".
The menu option "POWER" (heat
quantity counter) is only displayed
with those controllers that have this
function.
V 1 10 = Sensor version number
9
Menu CONFIG
The following settings are made here:
Language selection SPR DE / LAN EN
Time interval for continuing display TIME N
Time before jumping back to the 1st display TIME B
Address in the DL-bus network DL ADR
Entry of an offset value for sensor correction OFFSET
Language selection SPR DE/LAN EN
Switchover between German (DE) and
English (EN)
Factory setting: DE
To activate the language selection the RAS-PLUS must be initialised by scrolling forward in
the display level.
Time interval for continuing display TIME N
Entry 0 = no automatic forwarding between
the displays
Factory setting: 0
After a long key press "0" flashes
Selection of the desired time by a short key
press.
Confirmation of the desired time by a long
key press.
Entry 15 = The value display scrolls for-
wards every 15 seconds to the next display.
Adjustment range: 0 – 99 sec in second
steps
10
Time before jumping back to the 1st display TIME B
Entry = 0 There is no jump back of the dis-
play to the 1st value.
Factory setting: 0
After a long key press "0" flashes
Selection of the desired time by a short key
press.
Confirmation of the desired time by a long
key press.
Entry 60 = After 60 seconds without activa-
tion of the key button jumping back from
one of the additional programmed values to
the first display value (room temperature)
occurs. Adjustment range: 0 – 100 sec in
10 second steps
The jump back occurs only from the additionally programmed display values, not from one of
the base values.
Note: Only one of the two time options TIME N or TIME B should be selected.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Technische Alternative Accessori
