Technologic Systems TS-ENC530 Manuale utente
Enclosure TS-530 User Manual
16525 East Laser Drive
Fountain Hills, AZ 85268
TEL 480.837.5200
FAX 480.837.5300
http://www.embeddedx86.com/
Technologic Systems, Inc.
TS-ENC530 - 2
© COPYRIGHT 1998 - 200
TS Enclosure 530 User Manual
Rev. 1.2 TS-ENC530 - 3
Table of Contents
Product Overview ......................................................................................4
Introduction ............................................................................................................... 4
Features and Benefits............................................................................................... 4
Related Products....................................................................................................... 4
Software and Support............................................................................................... 4
Installing the Enclosure ............................................................................5
Electrostatic Discharge (ESD) precautions............................................................ 5
Setup and Installation Instructions ......................................................................... 5
Setup Procedure .............................................................................................................5
Disconnecting AC Power.................................................................................................5
Components...............................................................................................6
Standard Headers and Connectors ......................................................................... 6
Front Panel......................................................................................................................6
Rear Panel ......................................................................................................................6
COM1 9-Pin SubD Outs Table ........................................................................................7
COM2 9-Pin SubD Outs Table ........................................................................................8
Product Specifications............................................................................10
Dimensions .............................................................................................................. 10
Cabling ..................................................................................................................... 10
Environmental ......................................................................................................... 10
Options and Other Features ...................................................................11
Limited Warranty .....................................................................................12
Repairs ..................................................................................................................... 12
Not Covered............................................................................................................. 12
Out-of-Warranty Repairs ........................................................................................ 12
Regulatory Notices..................................................................................13
FCC Advisory Statement ........................................................................................ 13
Appendix A: Enclosure Views ................................................................14
Appendix B: User Manual Revisions .....................................................15
Contact Information.................................................................................16
Technologic Systems, Inc.
TS-ENC530 - 4
Product Overview
Introduction
The Technologic Systems TS-ENC530 is a metal enclosure designed to house the TS-3300 or
TS-5300 single-board computers and two PC/104 peripheral boards. This manual is intended
to provide the user with an overview of the enclosure’s features, benefits, specifications, and
set up procedures. It also contains important safety information.
Features and Benefits
The switching power regulator efficiently converts 12-38 VDC to regulated +5 VDC
required by the SBC
COM ports adapted to standard 9-pin Sub-D
Status LED's for Ethernet port are visible
Power Good LED visible on the rear panel
Surge suppression on DC power input
Sturdy metallic design reduces noise
Dimensions of the enclosure are 2-3/8" x 5" x 6"
Related Products
The TS-ENC530 enclosure is designed for the following single-board computers:
TS-3300
TS-5300
Software and Support
Free system software and documentation updates available on our web site
Free technical support by phone, fax, or email
30-day, money back guarantee on evaluation units
One-year, full warranty
TS Enclosure 530 User Manual
Rev. 1.2 TS-ENC530 - 5
Installing the Enclosure
Electrostatic Discharge (ESD) precautions
Before performing any set up or placement procedures, take the precautions outlined in this
section.
i Important
Be sure to take appropriate Electrostatic Discharge (ESD) precautions.
Disconnect the power cable at the rear panel of the enclosure before moving,
cabling, or performing any set up procedures.
Setup and Installation Instructions
Follow these guidelines for safety and maximum product performance:
Observe local health and safety requirements and guidelines for manual material handling.
Set the enclosure on a level surface with adequate ventilation.
Ensure the rubber feet are used for protection and stability on level surfaces.
Wall-mount the unit if placement on a level surface is not available, or desired.
Setup Tools
Depending on the placement and cabling of the enclosure, you may need the following tools:
Small flat-blade screwdriver
Small Phillips screwdriver
Setup Procedure
After locating, setting up, grounding, and cabling the enclosure:
1. Apply power to the unit.
The amber-colored LED on the rear panel should be lit.
2. Monitor COM2 using a terminal emulator to verify that the enclosure is operating
properly.
Disconnecting AC Power
1. Unplug the power cord from the power source.
2. Disconnect the power cord from the rear panel of the enclosure.
Technologic Systems, Inc.
TS-ENC530 - 6
Components
Standard Headers and Connectors
Front Panel
See Appendix A for a view of the enclosure’s front panel.
Rear Panel
2
2
3
3
4
4
5
5
6
6
1
1
TS Enclosure 530 Rear Panel Connectors
The rear panel of the metal enclosure has four connectors and two additional elements, as
indicated in the above view. Identifiers, and a description for each, are listed in the tables
below.
Identifier Connector Description
1
1
Ethernet
2
2
COM1
3
3
COM2
4
4
12-38VDC
Additional Elements
Identifier Description
5
5
Power Indicator LED
6
6
Chassis Grounding Lug
TS Enclosure 530 User Manual
Rev. 1.2 TS-ENC530 - 7
Enclosure TS-530 Ethernet Port
Ethernet: The Ethernet connector is a standard RJ-45 socket. It can be used to connect a
standard 10baseT Ethernet cable into the enclosed EPC.
Enclosure TS-530 COM1 Port
COM1: COM1 is brought in from the enclosed SBC. This 9-pin SubD connector is
industry standard for a PC. The TxD, RxD, RTS, CTS, and ground pins are supported for
RS-232 communications.
See the table below for RS-485 operation.
COM1 9-Pin SubD Outs Table
Half Duplex RS-485 RS-232 Full Duplex RS-485
9-Pin
SubD Signal 9-Pin
SubD Signal 9-Pin
SubD Signal
1
1
RX/TX + 1
1
1
1
TX +
2
2
2
2
Receive data 2
2
3
3
3
3
Transmit data 3
3
4
4
4
4
4
4
RX +
5
5
Ground 5
5
Ground 5
5
Ground
6
6
RX/TX - 6
6
6
6
TX -
7
7
7
7
Request to Send 7
7
8
8
8
8
Clear to Send 8
8
9
9
9
9
9
9
RX -
Technologic Systems, Inc.
TS-ENC530 - 8
Enclosure TS-530 COM2 Port, Pin 1
COM 2: COM2 is brought in from the base SBC. This 9-pin SubD connector is industry
standard for a PC. The TxD, RxD, RTS, CTS, and ground pins are supported for RS-232
communications.
COM2 9-Pin SubD Outs Table
RS-232
9-Pin
SubD Signal
1
1
2
2
Receive data
3
3
Transmit data
4
4
5
5
Ground
6
6
7
7
Request to Send
8
8
Clear to Send
9
9
Enclosure TS-530 12-38 VDC Connector
12-38VDC: The three-pin connector accepts 12-38 VDC of external power to supply
power to the board.
Power Indicator Light
Power Indicator Light: The amber-colored LED indicator on the rear panel, shown
highlighted above in red, is the power LED. It is lit whenever power is applied to the unit.
Chassis Grounding Lug
TS Enclosure 530 User Manual
Rev. 1.2 TS-ENC530 - 9
Chassis Grounding Lug: The lug labeled with the chassis ground symbol is used to
ground the chassis (optional).
Note
Connec
t this to earth ground during installation.
Technologic Systems, Inc.
TS-ENC530 - 10
Product Specifications
Dimensions
The TS Enclosure 530 measures 2-3/8" x 5" x 6"
Cabling
A mating power connector is supplied with the enclosure
A null modem cable is available as CB7-05
Environmental
To ensure optimum product operation you must maintain the operational environmental
specifications listed in the table below.
Environmental
Specifications
Standard Temp
Products
Extended Temp Products
Ambient Temperature 0 - 60° C
The internal temperature
must not exceed +70° C.
Allow for a much greater range.
Note: Refer to your product manual,
or contact Customer Service at
Technologic Systems if the
environmental temperature of the
location is in doubt.
Relative Humidity Not to exceed 90%
noncondensing
Not to exceed 90% noncondensing.
Indice
Altri manuali Technologic Systems Allegato
