Technologic Systems TS-ENC550 Manuale utente
Enclosure TS-ENC550 User Manual
16525 East Laser Drive
Fountain Hills, AZ 85268
TEL 480.837.5200
FAX 480.837.5400
http://www.embeddedx86.com/
Technologic Systems, Inc.
TS-ENC550 - 2
© COPYRIGHT 1998 - 2009
Technologic Systems Inc.
Enclosure 550 User Manual
Rev. 1.2
July 2009
Note
All modifications from previous versions are listed in Appendix B.
TS Enclosure 550 User Manual
Rev. 1.2 TS-ENC550 - 3
Table of Contents
Product Overview ......................................................................................4
Introduction ............................................................................................................... 4
Features and Benefits............................................................................................... 4
Related Products....................................................................................................... 4
Software and Support............................................................................................... 4
Installing the Enclosure ............................................................................5
Electrostatic Discharge (ESD) precautions............................................................ 5
Setup and Installation Instructions ......................................................................... 5
Setup Procedure .............................................................................................................5
Disconnecting AC Power.................................................................................................5
Components...............................................................................................6
Standard Headers and Connectors......................................................................... 6
Front Panel......................................................................................................................6
Rear Panel ......................................................................................................................6
COM1 9-Pin SubD Outs Table ........................................................................................8
COM2 9-Pin SubD Outs Table ........................................................................................9
COM3 9-Pin SubD Outs Table ......................................................................................10
DIO/ADC/COM4 25-Pin SubD Outs Table ....................................................................11
Product Specifications............................................................................13
Dimensions .............................................................................................................. 13
Cabling ..................................................................................................................... 13
Environmental ......................................................................................................... 13
Options and Other Features ...................................................................14
Limited Warranty .....................................................................................15
Repairs ..................................................................................................................... 15
Not Covered ............................................................................................................. 15
Out-of-Warranty Repairs ........................................................................................ 15
Regulatory Notices..................................................................................16
FCC Advisory Statement ........................................................................................ 16
Appendix A: Enclosure Views and Diagrams .......................................17
Appendix B: User Manual Revisions .....................................................19
Contact Information.................................................................................20
Technologic Systems, Inc.
TS-ENC550 - 4
Product Overview
Introduction
The TS-ENC550 metal enclosure is made to house the TS-5500 Single Board Computer and
two PC/104 peripheral boards. The switching power regulator efficiently converts 12-38 VDC
to regulated +5 VDC required by the SBC.
Features and Benefits
12-38 VDC input provides +5VDC to the SBC
COM ports adapted to standard 9-pin Sub-D
PCMCIA slot in front panel
2 USB ports available at back panel
DB25 connector allows 4th COM port or 8 A/D channels or 12 DIO signals to be available
at back panel
Status LED's for Ethernet ports are visible
Power Good LED visible at back panel
Reset button recessed into back panel
Surge suppression on DC power input
Sturdy metallic design reduces noise
Dimensions 2-3/8" x 5-3/8" x 7"
Related Products
The TS-ENC550 enclosure is designed for the TS-5500 Single Board Computer and two
PC/104 peripheral boards.
Software and Support
Free system software and documentation updates available on our web site
Free technical support by phone, fax, or email
30-day, money back guarantee on evaluation units
One-year, full warranty
TS Enclosure 550 User Manual
Rev. 1.2 TS-ENC550 - 5
Installing the Enclosure
Electrostatic Discharge (ESD) precautions
Before performing any set up or placement procedures, take the precautions outlined in this
section.
i Important
Be sure to take appropriate Electrostatic Discharge (ESD) precautions.
Disconnect the power cable at the rear panel of the enclosure before moving,
cabling, or performing any set up procedures.
Setup and Installation Instructions
Follow these guidelines for safety and maximum product performance:
Observe local health and safety requirements and guidelines for manual material handling.
Set the enclosure on a level surface with adequate ventilation.
Ensure the rubber feet are used for protection and stability on level surfaces.
Wall-mount the unit if placement on a level surface is not available, or desired.
Setup Tools
Depending on the placement and cabling of the enclosure, you may need the following tools:
Small flat-blade screwdriver
Small Phillips screwdriver
Setup Procedure
After locating, setting up, grounding, and cabling the enclosure:
1. Apply power to the unit.
The amber-colored LED on the rear panel should be lit.
2. Monitor COM2 using a terminal emulator to verify that the enclosure is operating
properly.
Disconnecting AC Power
1. Unplug the power cord from the power source.
2. Disconnect the power cord from the rear panel of the enclosure.
Technologic Systems, Inc.
TS-ENC550 - 6
Components
Standard Headers and Connectors
Front Panel
See Appendix A for a view of the enclosure’s front panel.
Rear Panel
8
8
3
3
4
4
7
7
5
5
6
6
1
1
2
2
TS Enclosure 550 Rear Panel Connectors
The rear panel of the metal enclosure has six connectors and two additional elements, as
indicated in the above view. Identifiers, and a description for each, are listed in the tables
below.
Identifier Connector Description
1
1
Ethernet 0
2
2
USB
3
3
DIO/ADC/COM4
4
4
COM1
5
5
COM2
6
6
COM3
TS Enclosure 550 User Manual
Rev. 1.2 TS-ENC550 - 7
Additional Elements
Identifier Description
7
7
12-38VDC and
Power Indicator LED
8
8
Chassis Grounding Lug
Technologic Systems, Inc.
TS-ENC550 - 8
Enclosure TS-ENC550 Ethernet Port 0
Left and Right LEDs highlighted
Ethernet: The Ethernet connector is a standard RJ-45 socket. It can be used to connect a
standard 10/100 Ethernet cable into the enclosed EPC.
Note
The right side LED above the Ethernet port indicates a 100-Mbit link, while
the left side LED indicates network activity. Both LEDs are highlighted red in
the above graphic.
Enclosure TS-ENC550 COM1 Port
Pin 1 highlighted
COM 1: COM1 is brought in from the base SBC. This 9-pin SubD connector is industry
standard for a PC. The TxD, RxD, RTS, CTS, and ground pins are supported for RS-232
communications.
COM1 9-Pin SubD Outs Table
RS-232
9-Pin
SubD Signal
1
1
2
2
Receive data
3
3
Transmit data
4
4
5
5
Ground
6
6
7
7
Request to Send
8
8
Clear to Send
9
9
TS Enclosure 550 User Manual
Rev. 1.2 TS-ENC550 - 9
Enclosure TS-ENC550 COM2 Port
Pin 1 highlighted
COM 2: COM2 is brought in from the base SBC. This 9-pin SubD connector is industry
standard for a PC. The TxD, RxD, RTS, CTS, and ground pins are supported for RS-232
communications.
COM2 9-Pin SubD Outs Table
RS-232
9-Pin
SubD Signal
1
1
2
2
Receive data
3
3
Transmit data
4
4
5
5
Ground
6
6
7
7
Request to Send
8
8
Clear to Send
9
9
Technologic Systems, Inc.
TS-ENC550 - 10
Pin 1 highlighted
COM3: COM3 is brought in from the enclosed SBC. This 9-pin SubD connector is
industry standard for a PC. The TxD, RxD, RTS, CTS, and ground pins are supported for
RS-232 communications.
See the table below for RS-485 operation.
COM3 9-Pin SubD Outs Table
Half Duplex RS-485 RS-232 Full Duplex RS-485
9-Pin
SubD Signal 9-Pin
SubD Signal 9-Pin
SubD Signal
1
1
RX/TX + 1
1
1
1
TX +
2
2
2
2
Receive data 2
2
3
3
3
3
Transmit data 3
3
4
4
4
4
4
4
RX +
5
5
Ground 5
5
Ground 5
5
Ground
6
6
RX/TX - 6
6
6
6
TX -
7
7
7
7
Request to Send 7
7
8
8
8
8
Clear to Send 8
8
9
9
9
9
9
9
RX -
Indice
Altri manuali Technologic Systems Allegato
