TECOM BT3021 Manuale utente

Document No.

CPE-U1-1210S-USR02-011N

Project Name:

Bluetooth AP

Date Issued:

08-30-2002

Revision:

0.1

User Manual of Bluetooth Access Point

Product User’s Guide

Approved by:

Neil Liu

Prepared by:

Jill Cheng

Department :

Mobile Communication S/W Department,

CPE R&D Division

TECOM CO., LTD. TECOM Bluetooth Access Point PROJECT

Prepared by: CPE-U1 Internal Document

[Product Revision Information] Page Revision Date Issued

User's Manual 1(4)0.1 08-30-2002

1. INTRODUCTION

1.1. The Bluetooth Technology

Bluetooth is a worldwide standard for the wireless exchange of data between two

compatible devices. It utilities short-distance radio link technology andreplaces the

traditional cable connections to enable wireless connections between desktop and

laptop computers, cellular phones, scanners, digital cameras, printers and other

devices. You can now transfer files between two computer, dial up to the internet using

the host computer’s modem or a cell phone, or even share a network connection

without literally attaching your cables to a device. To put it simply, Bluetooth unplugs all

our cables and lets you forget about cable clutter for a change.

1.2. What is Access Point

The Bluetooth Access Point is part of a family ofnetwork access solutions that create

Local Mobile Networks (LMN) of high-speed wireless connectivity. It is provides a

communications link to local networks and the Internet for mobile devices equipped

with Bluetoothwireless technology.

1.3. What’s in the box

Check if the following items are included in the package. If there are any items missing,

please contact your dealer.

lQuick Installation Guide

lBluetooth Access Point

lCD-ROM (include Quick Installation Guide, Product User’s Guide, Application

Setup Guide, Locator for Windows and Acrobat Reader)

2. PRODUCT OVERVIEW

After you connected the Bluetooth Access Point with Etherneton your network

environment. The Bluetooth Access Point can be searched and used by other

Bluetooth devices.

2.1. Basic Features

Bluetooth Access Point offers advanced features such as:

Up to seven simultaneous users utilizing the LAN Access Profile

128-bit link level authentication

128-bit link level encryption

Wireless Interface:

Bluetooth Core Specification 1.1

LAN Interface:

LAN Protocol:

IEEE 802.3x, ISO8802.3

IP over IEEE 802 (RFC 1042)

2.2. Bluetooth SIG Profiles

LAN Access Profile (LAP)

Dial-up Networking Profile (DUN)

TECOM CO., LTD. TECOM Bluetooth Access Point PROJECT

Prepared by: CPE-U1 Internal Document

[Product Revision Information] Page Revision Date Issued

User's Manual 2(4)0.1 08-30-2002

2.3. Bluetooth Clients supported

Point-to-multipoint with 1.1 clients supporting:

LAN Access Profile (LAP)

WEBSITE UPDATES FOR COMPATIBILITY MATRIX???

2.4. Configuration and Management

Local connection, over Bluetooth or Ethernet LAN

HTTP-based interface (RFC 2616/2617)

DHCP (RFC 2131) Client and Server

Static IP addressing

2.5. Bluetooth Radio

PARTNERSHIP DEALS

2.6. Bluetooth Security

Security Mode 1 (non-secure)

Security Mode 2 (service level enforced security)

Security Mode 3 (link level enforced security)

128-bit link level authentication

128-bit link level encryption

Non-discoverable mode

2.7. Physical

LED Status Indicators: Power/Status, Bluetooth and Ethernet Link and Activity

Hardware connectors: LAN port: RJ-45

Input Power Requirement: 6 to 9 VDC, 1.0 amp

3. Advanced Management and Configuration

Bluetooth Access Point reference design has two of the most usable management and

configuration interfaces in the market.

The basic Web Interface let user can monitor andconfigure Access Point and all of

Bluetooth devices information in anywhere.

Locator™ is a multi-purpose cross-platform PC utility that can manage all bluetooth

devices in a network through its simple interface. It is an ideal tool for auto-IP

assignment, IP settings, firmware upgrades, and Web Interface discovery.

3.1. Web Management and Configuration

If you have successful gone through the Quick Installation procedure in a

DHCP-enabled network, you may want to monitor the Bluetooth activityon your

Access Point through the Web Interface.

Information page will display System Information such as the Bluetooth name of the

Access Point, as well as, its firmware version and MAC address. It will also display

network setup information such UBAP’s Internet Settings (IP Address, Subnet Mask,

Gateway and DNS entries).

Devices page will display the IP and MAC addresses of all the currently connected

Bluetooth clients.

TECOM CO., LTD. TECOM Bluetooth Access Point PROJECT

Prepared by: CPE-U1 Internal Document

[Product Revision Information] Page Revision Date Issued

User's Manual 3(4)0.1 08-30-2002

If you do not have a DHCP-enabled network, or you would like to manually set up your

Access Point’s network configurations eg.its static IP address, then you can use the

Web Interface’s various advanced configuration pages such as Network, Bluetooth

and Maintenance.

3.1.1. Accessing the Web Interface

If you have access to a DHCP server, it will assign all the parameters needed for your

Access Point to connect to a network. Assignment through DHCP is the default setting.

There are two simple ways to find out the IP address of your Access Point that you will

need to access the Web Interface:

Using your Bluetooth Client:

1.Start the Bluetooth application in your client.

2.Search for devices

3.Choose Bluetooth Access Point from a list of found Bluetooth devices and

conduct service inquiry

Your client will also display its IP Address next to the Access Point’s Bluetooth name.

Figure 13Com’s Bluetooth Client displaying UBAP’s IP Address

You can simply enter this IP address in the address section of your Browser (eg.

Internet Explorer) to access the Web Interface.

Using the Locator:

TECOM CO., LTD. TECOM Bluetooth Access Point PROJECT

Prepared by: CPE-U1 Internal Document

[Product Revision Information] Page Revision Date Issued

User's Manual 4(4)0.1 08-30-2002

If your PC is in the same network with the Access Point, running the setup-free Locator

utility will automatically scan the network and identify your Access Point. It will display

the IP address.

Figure 2Locator displaying Bluetooth Access Point

To access the Web Interface, you can simply highlight Bluetooth Access Point and hit

the web icon on Locator (please refer to the Locator section for more information).

The default username and password for the Web Interface is admin and admin

respectively. You are encouraged to change these security settings as soon as

possible to prevent unauthorized access to the Interface.

3.1.2. Information

There are include Information and Devices pages.

Information page has display System Information and network setup information

about Bluetooth Access Point. Hit the Refresh button to get the current information

about your Access Point.

System Information: The Bluetooth name of the Access Point, firmware version

and MAC address.

TECOM CO., LTD. TECOM Bluetooth Access Point PROJECT

Prepared by: CPE-U1 Internal Document

[Product Revision Information] Page Revision Date Issued

User's Manual 5(4)0.1 08-30-2002

Network Settings: Access Point Internet Settings (IP Address, Subnet Mask,

Gateway and DNS entries).

Figure 3Information page on the Web Interface

Devices page displays information about the Bluetooth clients currently connected to

the Access Point. Hit theRefresh button to get the current status of connected

Bluetooth clients.

Note: The Bluetooth Link/Activity LED will light solid green if there is a connection

between Bluetooth Access Point and a Bluetooth client. It will blink rapidly if there is

Bluetooth network activity.

TECOM CO., LTD. TECOM Bluetooth Access Point PROJECT

Prepared by: CPE-U1 Internal Document

[Product Revision Information] Page Revision Date Issued

User's Manual 6(4)0.1 08-30-2002

Figure 4Devices page on the Web Interface

3.1.3. Network

This is an advanced setup page for the Network settings of Bluetooth Access Point.

Here you can set the Bluetooth namefor your Access Point. The factory default name

is Bluetooth AP. By default, the IP Address of Bluetooth Access Point is appended to

the Bluetooth name that will appear on Bluetooth clients. This is especially a useful

feature to identify the IP address assigned automatically by the DHCP server.

Also under Network you can decide which method to use for Bluetooth Access Point’s

IP address setting: Automatic through the DHCP server or Manual. If your IP Address

Mode is Automatic, then you don’t need to set up the Default IP Address, Default

Subnet Mask, and Default Gateway boxes.

If, however, you would like to set up aManualIP address for Bluetooth Access Point

(or if your network does not have a DHCP server). You will need to consult your

network administrator for a unique IP address on the network to enter into theDefault

IP Address box replacing the factory default 192.168.1.120. Your network

administrator will also give you the correct values for Default Subnet Mask (factory

default 255.255.255.0) and Default Gateway (factory default 192.168.1.1) to enter into

the appropriate boxes.

Finally you may decide to disallow Bluetooth clients to be able to access to the Web

Interface. This security feature will prevent unauthorized configuration from the

wireless side thereby restricting Web Interface access to the Ethernet side.

TECOM CO., LTD. TECOM Bluetooth Access Point PROJECT

Prepared by: CPE-U1 Internal Document

[Product Revision Information] Page Revision Date Issued

User's Manual 7(4)0.1 08-30-2002

Figure 5Network page on the Web Interface

3.1.4. Advanced Setup without DHCP

When Bluetooth Access Point is powered up, it automatically looks for a DHCP server

in the network to get an IP address for itself so that the Access Point is ready to use

without user intervention. However, if there is no DHCP server in the environment,

Bluetooth Access Point will reset to its factory default static IP address 192.168.1.120,

and will require manual setup for your network.

Note: If your network already uses the non-routable 192.168.1.X with the 192.168.1.1

Gateway Address, and if 192.168.1.120 is not taken by other elements in the network,

you do not necessarily need to change any settings. Your Access Point will work

immediately.

The quickest way to change the IP Address of the Access Point is through the Locator

utility. Simply connect the Access Point to your PC through across-over CAT5

Ethernet cable (or connect both Bluetooth Access Point and your PC to a hub through

normal Ethernet cables). Running Locator will enable you to discover the Access Point

immediately without a need to adjust the PCs subnet to that of the Access Point’s.

Thenyou can highlight the discovered Access Point and hit theConfigure button to

manually set the network parameters for the Access Point through theUse the

Following IP Address section. Please refer to the Locator™ Management and

Configuration section for more information.

TECOM CO., LTD. TECOM Bluetooth Access Point PROJECT

Prepared by: CPE-U1 Internal Document

[Product Revision Information] Page Revision Date Issued

User's Manual 8(4)0.1 08-30-2002

Figure 6Configuring the IP Address through Locator

Alternatively, you can use the Web Interface to manually set the IP address of the

Access Point:

1.Connect your PC to Bluetooth Access Point through a cross-over CAT5

Ethernet cable (or through a hub using normal Ethernet cables)

2.Change the network settings of your PC

Go to Start>Control Panel>Network Connections>

Click on LAN Connection (your system tray may have a little icon for the LAN

connection)

3.Click on Properties

4.Click on Internet Protocol (TCP/IP)

5.Choose Use the Following IP Address

6.Temporarily set IP address to 192.168.1.X (where X can be any 3 digit number

other than 120)

7.Temporarily set Subnet Mask to 255.255.255.0 (where X can be any 3 digit

number other than 120)

8.Temporarily set Default Gateway to 192.168.1.1

Now you will be able to connect to the Web Interface of the Access Point by typing

192.168.1.120 on your browser. Please refer to the previous Network section for the

manual setting of the IP Address.

Warning: Do not forget to change the network settings of your PC back to what they

were originally in your network.

3.1.5. Bluetooth

This is an advanced setup page for the Network settings for the Bluetooth clients

connecting to Bluetooth Access Point along with the Access Point’s Bluetooth security

settings.

Warning: If you have chosen automatic DHCP-assigned network settings for the

Access Point, you are strongly encouraged to leave the Bluetooth client IP and DNS

addresses Automatic as well. If you decide (strongly discouraged) to set the Bluetooth

Client IP Addresses to static, you must choose the same subnet of your Access Point

IP Address.

TECOM CO., LTD. TECOM Bluetooth Access Point PROJECT

Prepared by: CPE-U1 Internal Document

[Product Revision Information] Page Revision Date Issued

User's Manual 9(4)0.1 08-30-2002

You can leave the IP Addresses for Bluetooth clients Automatic even if the IP Address

of Bluetooth Access Point is set manually. You may, however, decide to set them

manually specifying a starting static IP Address in the same subnet of your Access

Point’s IP Address.

Warning: If the IPAddress of the Access Point is Static (eg. 192.168.1.120), and IP

Addresses of the Bluetooth clients are Automatic, then you have to make sure that

the 7 (or number of maximum allowable) IP Addresses after the IP Address of

Bluetooth Access Point (eg. 192.168.1.121 to 128) are unique.

Warning: If the IP Address of the Access Point is Static (eg. 192.168.1.120), and IP

Addresses of the Bluetooth clients areStatic, then you have to make sure that the 7

(or number of maximum allowable) IP Addresses starting with your specified range are

unique.

You can choose to allow up to 7 simultaneous Bluetooth client connections to the

Access Point.

By default, Bluetooth Access Point is in non-secure mode. Any Bluetooth client may

connect to it without encrypted authentication. However you are strongly encouraged

to use the Bluetooth passkey. By default theBluetooth passkey is set to “0000.” For

more security, please change this passkey.

In order to connect to the Access Point, the Bluetooth client will prompt the user to

enter the Bluetooth passkey thereby preventing unauthorized access to the Network.

Indice

Altri manuali TECOM Punto di accesso wireless

TECOM

TECOM WL5030 Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente