TEKNIX SCGH751B Manuale utente
0
SCGH751B & SCGH751X
1
These instructions have been drawn up for your safety and that of others. You
are therefore requested to read them carefully before installing and using the
appliance. Keep this instruction manual for future reference as necessary. If the
appliance is sold or moved, make sure that the manual is handed over to the new
user.
Installation
·Prior to installation, ensure that the local distribution conditions (nature of the gas
and gas pressure) and the adjustment of the appliance are compatible.
·This appliance is not connected to a combustion products evacuation device. It
shall be installed and connected in accordance with current installation regulations.
Particular attention shall be given to the relevant requirements regarding
ventilation
·Installation of the appliance and its connection to the electrical mains must only
be carried out by QUALIFIED PERSONNEL. Before any procedure, it is important
to check that the appliance is DISCONNECTED from the electrical mails.
·It is risky to modify or attempt to modify the characteristics of this product.
·After removing the appliance from the packaging, make sure that it is
undamaged and that the electrical lead is in perfect condition. Otherwise,
contact your dealer before putting the appliance into operation.
·The Manufacturer declines all responsibility in case of failure to comply with the
accident prevention regulations.
·Make sure that air is able to circulate freely around the appliance. Poor
ventilation produced a shortage of oxygen.
·Make sure that the appliance is supplied with the type of gas indicated on the date
plate on the appliance.
·Use of a gas cooking appliance produces heat and moisture in the room in which it
is installed. Ensure that the room is well ventilated by keeping the air intakes
open and in good working order or by installing an extractor hood with discharge
pipe.
·If the appliance is used intensively for a long time the effectiveness of the
ventilation will have to be increased, for example by opening a window or
increasing the power of any electric extractor fan.
2
During use
·This product is designed to cook food inside ordinary homes and for
non-professional purposes. It should not be used for any other purpose.
·After using the appliance, make sure that all controls are in “CLOSED” or “OFF”
position.
·If you use an electrical socket close to this appliance, take care that the cables of
the appliances you are using are far away from the hot parts of this appliance.
Children’s safety
·This appliance must only be used by adults. Make sure that children do not
touch the controls or play with the appliance.
·The exposed parts of this appliance heat up during cooking and remain hot for
some time even after it is switched off. Keep children well away until the
appliance has cooled down.
Cleaning and maintenance
·Keep the appliance thoroughly cleaned. Food residues may cause fire risks.
Service and parts
·In the instance of malfunctions. Never attempt to repair the appliance
yourself. Repairs by unskilled persons may cause damage and accidents. First
refer to the contents of this manual. If you do not find the necessary information,
contact your nearest Service Centre. Servicing work on this appliance must be
carried out by an authorized Technical Service Centre. Always request the use
of original spare parts.
Environmental protection advice
·All the materials used are environmentally compatible and recyclable. Please
make your contribution to conserving the environment by using the
separate waste collection channels available.
Decommissioned appliances
·Appliances which are no longer used or usable are not worthless waste.
Through environment-friendly disposal, a number of materials used in the
production of your appliance can be recovered.
·Find out about the current disposal options from your specialist dealer, or
your local authority.
·Before scrapping the appliances, cut the power supply lead and make it unusable.
Contents
For the User
For your safety ................................................................................................................ 1
Description of the hob ..................................................................................................... 4
Instructions for use ......................................................................................................... 13
Cleaning and maintenance .............................................................................................. 14
For The Installation Technician
Technical data ................................................................................................................ 4
Instructions for the installation technician ..................................................................... 7
Electrical connection ...................................................................................................... 9
Adapting to the different types of gas .......................................................................... 10
Building into fitted kitchen units ................................................................................. 11
Installation options ....................................................................................................... 12
Guide to reading the
instructions
The following symbols will help you
When reading the instructions:
Safety information
Step by step instructions
Suggestions and advice
Information concerning environmental protection
4
Description of the hob
Technical Data
Dimensions in mm:
Installation opening L x P 840x480
BURNER
TYPE
MAX
OUTPUT
MIN
OUTPUT
G20
20mbar
Kw Kw
Nozzle
Making
mm
Cons
M3/h
Small
Auxiliary
Burner
1.00 0.35 0.72 0.095
Medium
Semi-rapid
Burner
1.75 0.65 0.97 0.167
Large rapid
burner 3.0 1.0 1.15 0.286
Triple flame
burner 3.80 1.9 1.35 0.362
Gas intake connection G1/2ʺ
220- 240V~50/60HzElectricity supply
A_ Hob
B_Burner control knobs
C_Small auxiliary burner
D_Cast iron pan support
E_Medium semi-rapid burner
F_Large rapid burner
G_Triple flame burner
H_Cast iron pan support
7
Instructions for the installation technician
CAUTION: This appliance must only be installed and used in rooms with
permanent ventilation to local standards.
Installation of the appliance and its connection to the electrical mains
must only be carried out by QUALIFIED PERSONEL.
Before any procedure, it is important to check that the appliance is
DISCONNECTED from the electrical mains. The Manufacturer declines all
responsibility for any damage arising from installation in breach of the
regulations in force or from failure to comply with the accident prevention
regulations.
Installation premises
For proper operation of a gas appliance, the air necessary for the combustion of
the gas must be able to flow into the room naturally. The air must flow into the
room directly through openings in the outside walls. These openings must
have an unobstructed cross-section not less than 2m3/hfor each kw of power (see
total power in kw on the appliance nameplate).
This opening must be constructed so that it will not be
obstructed from inside or outside, or constructed close
to the floor. The opening is recommended to be on the
side opposite to that on which the flue gases are
discharged. If it is not feasible to provide these openings in
the room where the appliance is installed, the necessary
air may be taken from an adjacent room, provided that:
·This room is not a bedroom or a hazardous
environment;
·This room has ventilation;
·The ventilation between the room where the appliance
is installed and the adjacent room has openings.
·Minimum height from pan support to kitchen cabinet
board is 850mm.
Discharge of flue gases
Gas cooking appliances must discharge their flue
gases through hoods connected directly to flues or the
outdoors.
If it is not possible to install the hood (fig. B) an electric fan must be installed on
the outside wall or the window of the room, provided it is possible for the
ventilation opening
to be increased in proportion to the delivery rate of the fan (fig. C). For a kitchen,
the delivery rate of this electric fan must guarantee an hourly air exchange of 3-5
times its volume. In both instances, the use of flues already used by other
appliances to discharge the flue gases is forbidden.
Connection to the gas supply
The gas Connection must be made in accordance with
the local standards. When installing, fit a safety tap at
the end of the pipeline. The appliance leaves the factory
tested and set for the type of gas indicated on the
plate inside the bottom guard, close to the gas
connection pipe. Make sure that the type of gas to be
supplied to the appliance is the same as that shown on
the plate. Otherwise, follow the instructions provided in
the “Adapting to different types of gas” section.
For maximum efficiency and minimum consumption,
make sure that the gas supply pressure complies with
the values shown in the gas used is different from that
specified (or variable).a suitable pressure regulator must
be installed on the supply pipeline.
The union must be fitted on the end of the gas train. Complete with G1/2＂
threaded nut, fitting the gasket between the components as shown in the
illustration. The gaskets must comply with the local standards. Screw the parts
together without forcing, fit the union so that it points in the direction required
then tighten all parts.
Connection
Make the connection to the gas system using a rigid metal pipe and regulation
unions, or with a stainless steel hose complying with the local standard. If metal
hoses are used, take care that they do not come into contact with mobile parts
and are not crushed. This must also be checked if the hob is to be combined with an
oven.
The gas intake connection of the appliance has a “ male thread.”
When making the connection, take care not to apply stresses of any kind to
the appliance.
When the installation is complete, always check that all the unions
are absolutely tight using a soapy solution. Never use a flame to make
this check.
9
Electrical connection
The appliance is profited to operate with a
power supply voltage of 230Vsingle-phase. The
connection must be made in accordance with the
regulations and laws in force.
Before making the connection, make sure that:
1) The safety circuit-breaker and the
electrical system are able to withstand the
load of the appliance(see nameplate).
2) The power supply system has an
earth connection in good working order in
accordance with the regulations in force;
3) The socket or omni polar switch use are easily
accessible with the appliance installed.
Fit a plug suitable for the load on the power lead and
connect it to a suitable safety socket.
If you wish to make a direct connection to the mains,
an omni polar switch with a gap between the contacts of at least 3 mm, of
suitable rating for the load and complying with the regulations in force, must
be installed between the appliance and the mains. The switch must not break a
contact in the yellow/green earth wire.
The brown live wire (connected to the “L” terminal of the terminal board)
must always be connected to the live wire of the power supply mains.
In all cases, the power supply lead must be positioned so that it does not reach
a temperature 50oC above the room temperature at any point.
One example of an ideal route is shown in the illustration. The cable is guided
by means of band clamps fixed to the side of the cabinet, in order to avoid any
contact with the appliance underneath the hob.
10
Adapting to the different types of
gas
Changing the nozzles
1) Remove the pan standee.
2) Remove the burner caps and flame caps from the burners.
3) Use a size 7 socket wrench to unscrew and remove the
nozzles, replacing them with those corresponding to the
type of gas to be used (see the table).
4) Reassemble the parts, reversing the operations described
above.
5) Then replace the setting data (close to the mains gas
connection) with the one for the new type of gas If the pressure of the gas
used is different from that specified (or variable), a suitable gas pressure
regulator complying with the standard must be installed on the supply pipeline.
Setting the minimum level
1) Light the burner as already described.
2) Turn the tap to the minimum flame position.
3) Remove the control knobs.
4) PG TO NG:
Use a thin blade screwdriver to turn the by-pass screw
located above left of the gas valve, shaft as shown right.
Turn gently the by-pass screw clockwise to the end
completely then turn it anti-clockwise 1/2 turn for the Triple flame burner, 3/4
turn for the Large rapid burner, 1/2 turn for the Medium Semi-rapid Burner and
3/8 turn for the Auxiliary burner.
NG TO LPG:
Use a thin blade screwdriver to turn the by-pass screw located above left of the
gas valve shaft as shown right. Turn gently the by-pass screw clockwise to the
end.
5) Finally, check that the burner does not go out when the tap is turned quickly
from the maximum to the minimum position.
Questo manuale è adatto per i seguenti modelli
1
Altri manuali TEKNIX Piano cottura
