Tektronix Phaser 200E Guida alla configurazione

Cleaning Instructions

Phaser

200 Series

Color Printers

First Printing February 1995

063-1450-02

1995 by Tektronix, Inc., Wilsonville, Oregon. Printed in the United States of America.

Tektronix, Inc.

This instrument, in whole or in part, may be protected by one or more U.S. or foreign patents or patent

applications. Information provided upon request from Tektronix, Inc., P.O. Box 1000, Wilsonville, Oregon

97070-1000.

If acquired subject to FAR or DFARS, the following shall apply:

■

Unpublished Ñ rights reserved under the copyright laws of the United States.

■

Restricted Rights Legend Ñ Use, duplication, or disclosures by the U.S. government is subject to restrictions as

set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause at DFARS

252.227-7013, or in subparagraph (c) (2) of the Commercial Computer Software Ð Restricted Rights clause at

FAR 52.227-19, as applicable. Tektronix, Inc., P.O. Box 1000, Wilsonville, Oregon 97070-1000.

Tektronix

is a registered trademark of Tektronix, Inc. Phaserª is a trademark of Tektronix, Inc. for color printers

and related products.

Other marks are trademarks or registered trademarks of the companies with which they are associated.

Users safety summary

Terms in manual:

CAUTION Conditions that can result in damage to the product.

WARNING Conditions that can result in personal injury or loss of life.

Power source:

Do not apply more than 250 volts RMS between the supply conductors or between either supply

conductor and ground. Use only the speciÞed power cord and connector. Refer to a qualiÞed service technician

for changes to the cord or connector.

Operation of product:

Avoid electric shock by contacting a qualiÞed service technician to replace fuses inside the

product. Do not operate without the covers and panels properly installed. Do not operate in an atmosphere of

explosive gases.

WARNING Turning the power off using the On/Off switch does not de-energize the

printer. You must remove the power cord to disconnect the printer from the

mains. Keep the power cord accessible for removal in case of an emergency.

Safety instructions:

Read all installation instructions carefully before you plug the product into a power source.

Terms on product:

CAUTION A personal injury hazard exists that may not be apparent. For example, a

panel may cover the hazardous area. Also applies to a hazard to property

including the product itself.

DANGER A personal injury hazard exists in the area where you see the sign.

Care of product:

Disconnect the power plug by pulling the plug, not the cord. Disconnect the power plug if the

power cord or plug is frayed or otherwise damaged, if you spill anything into the case, if product is exposed to

any excess moisture, if product is dropped or damaged, if you suspect that the product needs servicing or repair,

and whenever you clean the product.

Ground the product:

Plug the three-wire power cord (with grounding prong) into grounded AC outlets only. If

necessary, contact a licensed electrician to install a properly grounded outlet.

Symbols as marked on product:

DANGER high voltage:

Protective ground (earth) terminal:

Use caution. Refer to the manual(s) for information:

WARNING:

If the product loses the ground connection, usage of knobs and controls (and other conductive parts)

can cause an electrical shock. Electrical product may be hazardous if misused.

Cleaning Instructions

iii

Contents

Introduction

..................1

Thermal Head

..................3

Paper-feed Rollers

................5

Paper-pick Rollers

................6

Transfer Roll Sensor Pad

............10

Drum

....................11

Exit Rollers

..................12

Cleaning Instructions

Keeping your printer a top performer

Introduction

By performing regular cleaning, you ensure that your printer produces the highest quality prints.

Regular cleaning also helps prevent paper jams, smudged or streaked prints and misregistration.

Cleaning the printer is easy; just follow the procedures given in the next few pages.

When to clean

Every time you replace the transfer roll, and whenever printing appears streaked, or media feeds

improperly, clean these parts:

Thermal head

Paper-feed rollers

Paper-pick rollers

Clean these printer parts every 5,000 prints:

Transfer roll sensor pad

Drum

Exit rollers

Troubleshooting

Problem Possible Solution

Vertical streaks on prints. Clean the thermal head.

Missing areas of primary colors (cyan,

magenta, yellow, black).

Clean the thermal head.

Smudges on one end of prints. Clean the paper-pick rollers.

Smudges throughout prints. Clean the paper-feed rollers and exit

rollers.

Phaser 200 Series

Important notes about cleaning

❑

Use isopropyl alcohol to clean your printer. It can be purchased at your local pharmacy. You

can also use cleaning wipes that are pre-saturated with isopropyl alcohol (Tektronix order

number 006-7824-00).

❑

90% isopropyl alcohol is recommended. If you use alcohol that is less than 90% pure, allow

extra time for the paper-feed, paper-pick and exit rollers to dry.

❑

Before cleaning any part except the paper-pick rollers: Dampen a lint-free wipe with isopropyl

alcohol.

Cleaning kit

A cleaning kit is shipped with the printer (Tektronix order number 016-1233-00). You will need the

contents of the cleaning kit to perform the cleaning procedures on the next few pages:

Lint-free cleaning wipes

A plastic bottle for isopropyl alcohol

A cleaning tray for cleaning paper-pick rollers

Cleaning Instructions (this book)

Cleaning

Instructions



Isopropyl

Cleaning Instructions

Thermal Head Ð

Clean every transfer roll change.



123



Isoprop

Pre-saturated

isopropyl

alcohol

cleaning

wipe



❑

Turn off the printer using the

switch on the side.

❑

Open the top cover.

❑

Open a pre-saturated

cleaning wipe packet and

remove the wipe

dampen

a lint-free wipe with

isopropyl alcohol.

Phaser 200 Series



Caution

The thermal head may be hot.

To avoid possible injury, let it

cool before cleaning it.

❑

Use the wipe to gently clean

the entire surface of the

thermal head. Cleaning in

one direction only prevents

dirt from being re-introduced

to the thermal head.

❑

Close the top cover. Turn on

the printer using the switch

at the side.

Cleaning Instructions



Paper-feed Rollers Ð Clean every transfer roll change.



1

❑

Remove the front cover by

pulling forward, using the

Þngergrips at each side.

❑

Clean the three paper-feed

rollers; rotate them as you

wipe so that all surfaces are

cleaned.

❑

Replace the front cover,

tilting it slightly toward you

to align the guide-tabs in the

top slot.

Phaser 200 Series



aper-pick Rollers Ð Clean every transfer roll change.



1

For A4-size (metric) trays



❑

Turn off the printer.

❑

Remove the paper tray.

Remove the paper or

transparencies from the tray.

If your printer has two paper

trays, be sure to remove both

trays.

❑

When removing paper or

transparencies, do

not

push

the paper trayÕs metal plate

down. If the metal plate is

down, put the paper tray in

the printer and pull it out

again; this returns the metal

plate to the

position.

❑

Remove the cleaning tray

from your cleaning kit.

Note

If you are using an A-size

(U.S.) paper tray:

not

break the endtabs off the

cleaning tray. Proceed to

tep 4 on the following page.

❑

If you are using an A4-size

(

metric

) paper tray:

break

both endtabs (

and

) off

the cleaning tray.

Altri manuali per Phaser 200E

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Tektronix Stampante

Tektronix

Tektronix Phaser 840 Manuale utente

Tektronix

Tektronix Phaser 540 Plus Manuale utente

Tektronix

Tektronix Phaser 340 Manuale utente

Tektronix

Tektronix Phaser 740 Manuale utente

Tektronix

Tektronix Z740/DX - Phaser 740 Extended Color Laser... Manuale utente

Tektronix

Tektronix Phaser 550 Manuale utente

Tektronix

Tektronix Phaser 600 Manuale utente

Tektronix

Tektronix DocuPrint 850 Manuale utente

Tektronix

Tektronix Phaser 750DX Manuale

Tektronix

Tektronix Phaser 300i Manuale utente

Tektronix

Tektronix Phaser 560 Manuale utente

Tektronix

Tektronix Phaser 360 Manuale

Tektronix

Tektronix Phaser 740 Manuale utente

Tektronix

Tektronix Phaser 440 Manuale utente

Tektronix

Tektronix PHASER 750 Manuale utente

Tektronix

Tektronix Z780GN - Phaser 780 Graphics Color Laser... Manuale del proprietario

Tektronix

Tektronix Phaser 340 Manuale utente

Tektronix

Tektronix PHASER 6200 Guida di riferimento

Tektronix

Tektronix PHASER 380 Manuale utente

Tektronix

Tektronix PHASER 240 Manuale utente

Tektronix

Tektronix Phaser 560 Manuale utente

Tektronix

Tektronix PHASER 240 Manuale utente

Tektronix

Tektronix Phaser 740 Manuale utente

Tektronix

Tektronix Phaser 440 Manuale utente

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente

IRA3D

IRA3D POETRY4 Manuale utente