TellSystem Communication ProCon GSM Manuale utente

ProCon GSM

PROFESSIONAL GSM/GPRS TRANSMITTER

INSTALLATIONAL AND USER’S GUIDE

Version: 2.1

ProCon GSM

Table of contents

Device description and function..........................................................................................................................................3

Figure 1: Device operation.............................................................................................................................3

Module buildup......................................................................................................................................................................4

Figure 2: the buildup of the module...............................................................................................................4

Figure 3: wiring diagram series terminal........................................................................................................4

Figure 4: Inserting the SIM card.....................................................................................................................4

Installation guide...................................................................................................................................................................5

Technical parameters.....................................................................................................................................5

Installation steps.............................................................................................................................................5

LED signals....................................................................................................................................................6

Connecting the module (PC)................................................................................................................................................6

Establishing connection using a USB adapter...............................................................................................6

Establishing connection using a Bluetooth adapter.......................................................................................7

Programming using the PC software...................................................................................................................................7

Connecting process.......................................................................................................................................8

Program buildup.............................................................................................................................................8

Checking module status.................................................................................................................................9

Switching off PIN code request on SIM card.................................................................................................9

Event Log Readout......................................................................................................................................10

Readout of GSM signal strength..................................................................................................................10

Fill out basic data.........................................................................................................................................10

Saving phone numbers for notification.........................................................................................................11

Saving controlling phone numbers...............................................................................................................11

Time zone settings.......................................................................................................................................12

Input configurations......................................................................................................................................12

Figure 5. Normally Open (NO) and Normally Close (NC) wiring.................................................................12

Voice message settings...............................................................................................................................13

Adjusting outputs..........................................................................................................................................14

Figure 6: EXP Relay and EXP Relay3.........................................................................................................14

Tamper settings............................................................................................................................................15

Power supply monitoring setup....................................................................................................................15

Life signal sending setup..............................................................................................................................15

Anti Jammer System (AJS) settings............................................................................................................16

SMS notification of arming/disarming..........................................................................................................16

GSM alarm center expansion panel.............................................................................................................16

Figure 7. Alarm center expansion card wiring diagram................................................................................16

Remote surveillance settings (voice call).....................................................................................................17

Using your own signal (Contact ID) codes...................................................................................................17

GPRS settings..............................................................................................................................................17

Other settings options..................................................................................................................................18

Starting the program....................................................................................................................................19

Connecting to the module............................................................................................................................19

The menu tree..............................................................................................................................................19

Programming with SMS commands..................................................................................................................................20

Command List:.............................................................................................................................................20

SMS command examples:...........................................................................................................................21

GSM gate control compact view........................................................................................................................................22

Page 2

ProCon GSM

Device description and function

The GSM/GPRS device can be used for remote controlling (ex.: gate opener), as an accessory to alarm centers and also

as a standalone alarm center. The module has 4 contact driven inputs and one implemented relay output (relay type:

NO/NC). The module can be expanded with further outputs and functions.

It can send notification to 8 phone numbers in SMS and/or voice message. The notification sending can be triggered by a

signal arriving to any of the 4 inputs, by power failure, by sabotage or by arming/disarming of the GSM module. The

notifications can be accompanied by an additional voice message that will be played when calling is answered. These

recordings can be 8 seconds utmost. The voice message can be also a shared identifying message with a maximum

length of 15 seconds.

Output control can be made from unlimited phone numbers with a free call. When controlling with caller identification

numbers can be stored in the memory of the module (1,000 in this case), or on the SIM card inserted. With caller

identification unauthorized controlling of the device connected to the output is not possible.

Output can be controlled also with SMS command that might even contain differing order from stored settings (ex. output

set to bistable can be controlled for 10 seconds). You can find more information on this command on page 20.

DTMF controlling was implemented thus GSM module outputs can be controlled separately with mobile phone buttons.

This mode has the condition to accept the call arriving to the module that involves call charges depending on the carrier.

The module can store up to 16,000 events in which appear states of the inputs and outputs, power supply resets, GSM

network and module state related information, incoming and outgoing calls and SMSs.

The tamper input on the module can be used as a sabotage indicator with setting possibilities alike to inputs. Shortening it

before powering on then cut short in 3 seconds functions as a ’’reset’’ that can revert the module back to its original

factory state.

Implemented Anti Jammer System (AJS) protects from GSM jammers. The significant dropping of the GSM strength or a

network connection failure initiates a prompt alarm. In these situations module tries to send notifications using network

possibilities still available. It can be set that by controlling the output even a siren can be managed. This possibility is

especially useful if we would like to fob the person who committed the sabotage.

As a standalone alarm center 4 zones can be distinguished and they can have Contact IDs or zone codes. The types of

the inputs can be altered based on that (ex. 24/7, delayed etc.). By using expansion panel (EXP Alarm) an LED status

feedback is available of the armed/disarmed module status and also the control of a peripheral buzzer in case of arming

disarming and alarm event.

Besides continuous voltage monitoring the module observes also the GSM strength. These data can be readout and

these can be charted even by hourly divisions by the programming and surveillance software.

By using expansion panels further outputs (EXP Relay, EXP Relay3), or expansion panel for standalone GSM alarm

center (EXPAlarm) can be connected

The module can be programmed by SMS command, voice menu, PC or by Android mobile phone.

Figure 1: Device operation

Page 3

ProCon GSM

Module buildup

Figure 2: the buildup of the module

Figure 3: wiring diagram series terminal

Figure 4: Inserting the SIM card

Page 4

ProCon GSM

Installation guide

Technical parameters

•Power voltage: 9-20 VDC

•Standby power drain: 30 mA

•Maximum power drain: 700 mA

•Relay output load: max. 20V / 500 mA

•GSM module type: SIMCOM 900

•GSM frequencies: GSM 850 / EGSM 900 / DCS 1800 / PCS 1900 (Multi- Band)

•SIM card usage: brand free GSM module

•GSM antenna type: SMA connector (comes with package)

•Size: 78 x 51 x 20 mm, packed: 132 x 128 x 32 mm

•Operation temperature: -20°C - +50°C

Installation steps

1. Carry out a signal strength check with your mobile phone. Sometimes occurs there is no sufficient signal strength

at the commissioning site. In this case it is recommended to change the module position prior to installation.

Do not install the device to places where strong electromagnetic waves might occur, ex. next to electric motors or

alarm transformers.

2. Do not install in watery places or to places with great humidity.

3. Connect the antenna that can be secured with an SMA connector. If you are reading low signal strength use

antenna with higher gain. Signal strength grow can also be achieved by repositioning the antenna. Do not

position the antenna under various metal covers as those might significantly ruin the signal strength.

4. You should opt out the PIN number request, voicemail and call notification of the SIM card. Sometimes

new SIM cards must be activated (usually one outgoing call has to be made). Check the validity of the card. If you

have a prepaid card check its balance and its usage possibilities (ex. can be used only for calls).

5. Number identification of caller and at call initiations has to be checked. This function at certain service providers.

Must be enabled formerly.

6. Insert the SIM card in the SIM card slot of the module.

7. Connectors have to be connected according to the wiring diagram. If you are dealing with OC output (output of

EXP Alarm expansion panel) mind the correct wiring of the relay protecting diode.

8. If you are working with OC relay be cautious especially of avoiding electric shock. A proper contact protection

must be established. If you lack the appropriate experience ask for professional help.

9. Check if the power supply performance will be sufficient for the module. Mind the polarity.

If wiring is reversed the module will not operate or might get damaged.

10. Now the device can be connected to the power supply.

11. If you have purchased also a battery connect it to the device. Use only the appropriate battery for reserve

powering the device!

12. After connecting the voltage supply the red LED is lighted indicating the device establishing connection with the

GSM system (this can be 1 minute utmost).

13. If red LED goes off and green LED flashes module is online and connected to network. The flash number(s)

indicates GSM signal strength.

For programming the power supply must be connected! Power needed for programming can be supplied to the

module also from USB adapter.

Page 5

ProCon GSM

LED signals

Signals give essential information of the module, of GSM signal strength and the actual error codes. By blinking we mean

flashes between two longer pauses.

•A STATUS LED (green) gives feedback of signal strength value based on the chart below:

Flashes Signal quality

1Bad

3 Decent

4 Good

5 Excellent

LED lighted GSM connection rejected

•

An ACT LED (red) lit means the initiation process at startup. At this phase module performs the initial checks.

During operation this reflects an event (SMS or voice call).

•

If the red and green LED are lighted simultaneously it tries to communicate an error that can be identified with

the chart below: Flashes Error code

1 Initializing

2Bad GSM module

3SIM card not inserted

4SIM card locked with PIN

code

10 Modem mode

•Alternating flashes of red and green LEDs means the ’’reset” function of the tamper input. This way the GSM

module can be reverted back to its original factory settings.

Connecting the module (PC)

Establishing connection using a USB adapter

1. Connect the USB adapter to the Program labeled slot of the module.

2. USB adapters can provide the sufficient voltage for programming the GSM module.

3. Attach the USB connector of the adapter to a USB extension cable and plug into any USB port of a PC.

4. WARNING! If you are using Windows Xp operating system the system offers an automatic driver installation.

IMPORTANT, do not use the offered driver but carry on the installation with the USB driver.

Installing the USB driver manually in 10 steps

✔get the required driver from our web site or from the ‘’USB driver’’ directory on the CD if you have

the USB Kit

✔use the appropriate 32 or 64 bit version for your operating system in the installation process

✔to check this use the Control Panel →System menu path (when using Windows XP ‘’x64 Edition”

will only appear if the system is running on 64 bit)

✔connect the USB programmer to your PC

✔do not chose the automatic installation offered by the system

✔Open the path Control Panel →System→Hardware Device Manager window.

✔In this window search for Unknown device (which will be the programmer now, later the USB

Serial port). If you cannot find it start the “Scan for hardware changes” process from the upper

window menu.

✔Device properties can be achieved by double clicking on the unknown device.

✔Start the Update driver process

✔In the installation window choose the manual selection of the driver location then choose the

Page 6

ProCon GSM

appropriate folder containing the 32 or 64 bit driver

✔Click on the Next button to start the installation.

5. Open the Device Manager (click on System→Properties→Hardware tab →Device manager)

6. Search for a device named USB Serial port (COM…) under Ports

1. If a driver reinstall is needed click on the device then choose driver removal then follow instructions above.

7. Start the programming software.

8. You have to set the value in brackets [USB Serial port (COM…)] in the programming software

9. Establish a connection to the GSM module.

Establishing connection using a Bluetooth adapter

1. Connect the Bluetooth adapter to the GSM module and provide power to it.

2. Switch on the Bluetooth connection possibility on your device (PC or Android mobile phone).

3. Search for programmer with the help of your Bluetooth enabled device.

4. After finding the adapter you can pair your PC/smart phone with the adapter using the code “1234’’.

Search for the COM port number of the connection (usually under Properties →Hardware tab)

5. Search for the COM port number of the connection (usually under Properties →Hardware tab)

6. Set the port number also in your programming software (PC) or choose the automatic port finding option.

7. Establish a connection to the GSM module.

If you use Windows 8 operating system the programming software should be started in “Windows XP SP2/SP3”

compatibility mode (Right click on the starting icon of the program →Properties →Compatibility)

In every case you can check the connection if you see the connected module name next to the Start button in the

programming software and the green LED on the programmer starts to flash.

If you have a connection established between the adapter and your PC or mobile phone you can start the module

configuration.

•By clicking the Start button after the connection was established modules settings will be

acquired.

•By clicking the Start/Default config button (after a confirmation) it will revert back the module to

factory settings.

•Using the Android application settings are always acquired after establishing a connection.

Programming using the PC software

•If you have chosen configuration by PC you can use our software that is freely downloadable from our

website or you can find it on the installation CD in the USB KIT.

•The program runs automatically, no installation needed

•Compatible with operating systems Windows XP, 7 and 8

•Make sure you always use the latest software!

•If newer software is out the module should be updated prior to the first configuration.

Page 7

ProCon GSM

Connecting process

•To program the module choose between USB or Bluetooth connection.

•Below the language selection in the scroll down list (COM 4 in the picture) you can select the port through

which you would like to communicate with the module programmer. You can find this value (in Windows

operating system) under Device manager →Com port at the connected programmer. If you cannot decide

you might let the program to search for it by pressing the automatic COM port finding. The automatic COM

port search might take several minutes.

•If the connection was successful you will see under the Product connection tab the name of the module.

•Clicking the start button the software connects to the module and reads out its settings.

•By clicking the Start/Default config button the module will be set back to default factory settings after the

connection was established. (Before the operation the software asks for confirmation if this feature has not

been switched off before).

•If you do not want to attach a module just to inspect the settings options you can select the Products-tryout

window where you can freely make a specific module properties selection and also module preprogramming.

Program buildup

•Upper menu items:

◦Maintenance: basic menus needed for module maintenance (for ex. module state check, event log

readout, PIN code request switch off of the SIM card, Firmware upgrade)

◦File commands: Saving and loading settings

◦Descriptions: viewing wiring diagram

◦Settings: setting window size, switch off confirming dialogs

◦Language: language selection (available languages: English, Hungarian, Italian, German, Slovak,

Slovenian, Dutch, bohemian, Finn, Romanian)

◦Contact: our contacts; e-mail addresses and phone numbers

◦GSM: reverting back to factory settings the GSM chip (SIM900 chip) and auxiliary PSTN line monitoring

(in case of a failure), providing GSM information, saving central SMS number of the network operator

•You can reach the various settings of various items by clicking the appropriate tab

•On the main page (Basic data tab) clicking the Clock Synchronization makes the module to adjust its time

to the PC clock.

•After the device established a connection with the mobile network it will automatically adjust the time with the

mobile network (if this feature is available).

Page 8

ProCon GSM

•The Reading and Sending buttons at the bottom are for readout and edit of the module configuration. These

buttons are accessible everywhere except on the Controlling phone numbers tab.

You should send data to the module with the Send button after every significant modification.

Before sending your settings make sure those will not trigger an unexpected alert. You should readout the

actual module state beforehand (Maintenance tab).

WARNING! After connection always readout the settings first if you would like to alter those.

•You can restart the module with the Restart button. After monitoring is complete the module should

be restarted.

•In the lower menu line you can be informed of the followings:

◦Communication port number

◦GSM module name

◦Firmware version number

◦Notification on the actual software process

◦ProRead version number

Checking module status

You can reach the actual status through Maintenance →Show module status button

By the module status query you will be informed of the followings:

•input statuses

•output statuses

•Tamper sabotage notification

•power supply failure notification

•armed/disarmed module status

•displaying occurring error/event codes (ex.: no SIM card inserted, SIM card locked by PIN code)

•checking Contact ID code (to monitoring station) sending process (ex. handshake status)

•GSM connection status (ex. connected to the network, roaming, no connection, connection rejected)

•actual GSM signal strength (refreshing in seconds)

Switching off PIN code request on SIM card

Before inserting SIM card in the module the PIN code request should

be switched off

•If you have not done yet then you can switch off at

Maintenance→Switch off PIN code request.

•You will see the following window, where you can input the code

and its request will be switched off.

Page 9

ProCon GSM

Event Log Readout

The event log can be viewed by clicking Maintenance →Read Event Log button:

•It can store up to 16,000 events in FILO (first in-last out) mode

•The acquired list can be saved in ‘’csv” file for later examination. This can be done also in the event list by clicking

the ‘’Open csv” button.

•In the Token column there are short event information.

•In the Date column notification dates are stored. IMPORTANT! Date will be accurate if the clock of the module is

synchronized with a PC or with GSM system. The latter is automatically done by the module when connected to

the network of the operator.

•The GSM 0-31 indicates the signal strength at the time of creation. 31 is the highest, 0 indicates state with no

connection.

•Network indicates if the module was connected to the network carrier at the time of creation.

•In the Comment/parameter column notification related extra information are stored.

•Initially the chart is empty; the readout can be commenced by pressing the Readout event log button.

•The newest data will appear at the top of the list followed by older entries as you go down the chart.

•If the whole chart readout is not necessary you can stop it with the Readout stop button.

•Read out list can be exported from the software in ’’csv’’ (ex. Excel) chart so later it can easily be sent and stored.

Readout of GSM signal strength

The chart of GSM signal strength is available by the Maintenance →

Show GSM signal strength button

•You can have the values by pressing the Readout button

•Measured readings can be displayed by clicking the

’’Reading’’ button.

•Signal strength fluctuations are divided by hours. Passed time

should be interpreted according to this.

•Vertical scale is calibrated from 0 to 31. 31 mean the best

signal strength.

•Size of the chart can be freely altered by left click.

Fill out basic data

Important data of the installed GSM module can be set. Besides

the client name and commissioning address the phone number

of the SIM card inserted in the module and the type of the

attached alarm center also can be set.

•Data inserted are stored in the module

•Stored data can be useful later during maintenance.

Page 10

Indice

Altri manuali TellSystem Communication Trasmettitore

TellSystem Communication

TellSystem Communication EasyCon GSM Manuale utente

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente