Tempest Breeze 58.025 Manuale utente
Breeze User Manual 1
User Manual
Breeze
Revision 01.1
September 2017
© Tempest Lighting, Inc.
Breeze User Manual 2
Table of Contents
Introduction ................................................................................................................................................................................................ 3
IMPORTANT: Safety Advisories.............................................................................................................................................................. 3
Installation................................................................................................................................................................................................... 4
Dimensions, Rigging Points, and Maximum Projector Dimensions/Power ......................................................................................... 4
Air Clearance....................................................................................................................................................................................... 5
Snow Clearance .................................................................................................................................................................................. 5
Operating Temperature Range.......................................................................................................................................................... 5
Mounting Bolts ................................................................................................................................................................................... 6
Hanging a Breeze Enclosure............................................................................................................................................................... 6
Wiring the Enclosure .................................................................................................................................................................................. 7
Power Wiring .......................................................................................................................................................................................... 7
SAFETY NOTICE: .................................................................................................................................................................................. 7
Electrical Standards ............................................................................................................................................................................ 7
Wiring Access...................................................................................................................................................................................... 8
One or Two Power Circuits? .............................................................................................................................................................. 9
3.4 Connect AC Wiring to MiniDEC Controller............................................................................................................................... 10
Mounting the Projector............................................................................................................................................................................ 11
Ceiling or Tabletop................................................................................................................................................................................ 11
Mounting and Aligning ......................................................................................................................................................................... 11
Connecting Equipment......................................................................................................................................................................... 11
Routine Maintenance ............................................................................................................................................................................... 12
Clean Port Glass................................................................................................................................................................................ 12
Check Filter ....................................................................................................................................................................................... 12
Clean Filter........................................................................................................................................................................................ 12
Replacement Filters.......................................................................................................................................................................... 12
To Remove Filter............................................................................................................................................................................... 12
After Sales Support............................................................................................................................................................................... 12
Troubleshooting........................................................................................................................................................................................ 13
Warranty ................................................................................................................................................................................................... 14
Breeze User Manual 3
Introduction
Thank you for purchasing a Tempest enclosure! We have worked hard to provide you with the very best
product available for its purpose, and we shall continue to do everything possible to ensure that it works
well for you for many years to come.
Please read this manual before starting work!
In the event of difficulty, please contact your Tempest reseller or Tempest direct:
+1 818 787 8984
We will do everything we can to help you get the very best results from your Tempest enclosure.
IMPORTANT: Safety Advisories
All installation and rigging work done must where applicable be designed and built in accordance
with norms and standards of the local authority having jurisdiction of the installation site. It is the
responsibility of the installer to obtain such approvals as may be required to achieve full
compliance.
All electrical work must be carried out by a suitably licensed electrical contractor in full
compliance with local electrical standards.
Lifting: some enclosures and the equipment inside them may be heavy. Use properly rated lifting
equipment where appropriate and never attempt to carry out work with fewer than the number
of workers needed to lift safely.
It is the responsibility of the installer to ensure that all local building, safety and electrical codes
are strictly adhered to in the installation of this enclosure. Tempest Lighting, Inc., its employees
and agents are in no way responsible for damage arising from failure to follow either the
instructions in this manual or building, safety and electrical codes prevailing at the installation
location.
Do not attempt to install or operate the enclosure before fully reading and understanding this
manual
Never allow anyone who has not read this manual to open the enclosure or perform maintenance
on the projector within.
Never leave the enclosure unattended when open.
Always make sure all bolts and latches are tight and safety locks are in place after performing any
form of maintenance on the unit.
Do not open any electrical boxes until power has been shut off to all supply lines to the enclosure
(including the one powering the projector).
Do not open the enclosure in wet weather.
Breeze User Manual 4
Installation
Dimensions, Rigging Points, and Maximum Projector Dimensions/Power
Model
Format
Length
Width
Height
M1
M2
Weight
Projector Max:
Size (LWH) *
Projector
Max Power
58.025
Landscape
559
22in
478
18.8in
241
9.5in
445
17.5in
368
14.5in
16kg
35lb
410x410x150
16x16x6in
500W
52.050
Landscape
762
30in
595
23.5in
318
12.5in
648
25.5in
483
19in
21kg
45lb
610x521x229
24x20.5x9in
800W
52.100
Landscape
864
34in
702
27.6in
346
13.6in
749
29.5in
588
2.16in
30kg
66lb
695x595x275
28x24.5x10in
1,000W
52.150
Landscape
1041
41in
702
27.6in
397
15.6
927
36.5in
588
2.16in
41kg
90lb
890x622x254
35x24.5x12in
1,600W
Note: Be sure to allow for the length of the lens and for connectors, cables and
cable bend radii when calculating dimensions
Breeze User Manual 5
Air Clearance
Observe the minimum clearances shown around your
enclosure
Snow Clearance
In areas where snow is likely, make sure the base of the
enclosure is at least 24” [60cm] above highest potential
snow drift level.
Operating Temperature Range
Breeze may be used safely in locations where minimum
temperatures do not fall below 0°C [32°F].
Maximum ambient temperatures when the projector is
running (usually after dark) should not be higher than 2-
3°C below the projector’s stated maximum
environmental limit. So, for a projector with a 45°C limit,
ambients up to around 42° are ok. During daytime the
enclosure fan will run automatically if the internal
temperature exceeds 35°C.
If these conditions are not met, Breeze may not be the
right enclosure for your project –consider upgrading to a
Tempest Blizzard enclosure.
Allow 1m/3ft for access on
at least one side
75mm/3in
60cm/24in
Breeze User Manual 6
Mounting Bolts
Each Enclosure must be mounted with FOUR points.
All mountings must be made using the four M8
threaded holes on the bottom of the enclosure.
Use a 5mm hex key to secure the M8 socket cap
screws provided.
If the screws provided are not long enough to reach
through your structure, use any stainless steel M8-
1.25mm screw of sufficient length.
Tempest Lighting recommends the use of stainless
steel mounting hardware.
Make sure the inlet filter has at least 75mm/3in
clearance below.
IMPORTANT SAFETY NOTICES
Installer must ensure that all mounting points are secure
and conform to local safety regulations. Tempest Lighting
Inc. accepts no responsibility for damage or injury arising
from inappropriate or unsafe installation.
Hanging a Breeze Enclosure
If you need to hang your Breeze enclosure –for example
below a ceiling or soffit, use the four hanging adapter
plates supplied, along with M12 or ½” threaded drop
rods, as shown here:
5mm
Hanging adapter Plates
(included)
Drop rods (not included)
Breeze User Manual 7
Wiring the Enclosure
Power Wiring
SAFETY NOTICE:
All electrical wiring and termination MUST be carried out by
a suitably qualified and/or licensed professional, in
accordance with electrical and safety norms applicable in the
jurisdiction of the installation. Tempest, its employees and
representatives will not be liable for any damage arising
from failure to observe this requirement.
Electrical Standards
Important:
Fans and electronics are rated 115V or 230V, dependent on
electrical standard.
Enclosure model numbers ending .US are for use in countries
using US and Japanese style electrical systems:
100-120VAC 50/60Hz
Enclosure model numbers ending .IN are for use in countries
using European style electrical systems:
200-230VAC 50/60Hz
Remove the cover fixing screws, using a 4mm Hex Key.
Lift off the top cover.
4mm
Breeze User Manual 8
Wiring Access
Remove the MiniDEC Controller cover, by releasing the three
M4 thumb nuts.
Ground/Earth Terminal
Fan Terminal
AC Conduit Entry
Projector Outlet*
AC Terminal Block
* Your Breeze enclosure comes with a
rewirable C14 plug to fit this power
outlet.
You MUST connect projector power to
the C13 outlet. If this is not done, the
controller will not sense projector
function and the projector will quickly
overheat.
MiniDEC
Controller Cover
M4 Thumb nuts
Breeze User Manual 9
One or Two Power Circuits?
Tempest enclosures may be wired on single or double circuit
supplies. On a single feed, both enclosure and projector are
permanently on. With a split (double) feed supply, you can
switch off the projector when not in use, while the enclosure
continues to protect it 24/7.
Tip: most people use single feed.
Single Feed
Enclosure and projector are permanently on.
Enclosure and Projector must be rated for the
same voltage.
Supply must be rated for projector current plus
100 watts.
Supply must be permanently ON.
Split feed
Enclosure power must be permanently ON.
Projector power may be switched off.
Enclosure power must be rated for 100 watts.
Projector power must be rated for the projector
(see projector manual).
Projector and enclosure power must be same
voltage.
1
1
2
Single Feed
Split Feed
Breeze User Manual 10
3.4 Connect AC Wiring to MiniDEC Controller
Single Feed Operation
Note: European wire colors shown for illustration only.
Split Feed Operation
Single Feed Wiring
Feed the controller with a single maintained supply. The
enclosure should be powered 24/7. The projector must
be switched off when needed using the projector control
system.
Breeze ships configured for single feed wiring operation.
Split Feed Wiring
You may switch off the supply to the projector without
interfering with the cooling fan operation. Connect feeder
wires as shown, AND CUT THE COPPER LINKS ON THE
MiniDEC BOARD IN TWO PLACES, AS SHOWN. Fan circuit
should be maintained 24/7.
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Tempest Proiettore
