Terasic Apollo-S10 Manuale utente

Apoolo-S10

User Manual

www.terasic.com

March 31, 2020

1.1. Q

Apoolo-S10

User Manual

www.terasic.com

March 31, 2020

Contents

Chapter 1 Overview ...................................................................................4

1.1 General Description ..............................................................................4

1.2 Board Layout.........................................................................................4

1.3 Key Features.........................................................................................6

1.3. Block Diagram.......................................................................................8

1.4. Mechanical Specifications.....................................................................8

1.5. Power Requirement ............................................................................10

1.6. Connectivity.........................................................................................11

Chapter 2 Board Component..................................................................14

2.1 Configuration Interface........................................................................14

2.2 Setup and Status Components ...........................................................18

2.3 General User I/O.................................................................................22

2.4 Micro SD Card Socket.........................................................................24

2.5 FMC Connector...................................................................................25

2.6 FMC+ Connector.................................................................................37

2.7 Clock Circuit........................................................................................53

2.8 USB to UART for HPS.........................................................................56

Apoolo-S10

User Manual

www.terasic.com

March 31, 2020

2.9 DDR4 SDRAM ....................................................................................57

2.10 USB 2.0 OTG PHY..............................................................................68

2.11 Gigabit Ethernet..................................................................................69

2.12 1x6 GPIO Header................................................................................70

2.13 System Status Interface......................................................................71

Chapter 3 System Builder .......................................................................73

3.1 Introduction .........................................................................................73

3.2 General Design Flow...........................................................................74

3.3 Using System Builder..........................................................................75

Chapter 4 Dashboard GUI .......................................................................84

4.1 Driver Installed on Host.......................................................................84

4.2 Run Dashboard GUI............................................................................87

Chapter 5 Additional Information...........................................................96

5.1 Getting Help........................................................................................96

Apoolo-S10

User Manual

www.terasic.com

March 31, 2020

Chapter 1

Overview

his chapter provides an overview of the Apollo S10 Development Board and

installation guide.

1.1 General Description

Designed for modular and scalable high-performance FPGA Prototyping and HPC

solutions, Apollo S10 packs unbeatable performance and energy efficiency in a tiny

form factor and provides up to 90X performance increase over CPUs for critical

workloads such as simulation acceleration, molecular dynamics, machine learning.

Apollo S10 takes advantage of the latest Intel® Stratix® 10 SoC with 2800K logic

elements to obtain speed and power breakthrough (with up to 70% lower power).

Combining a number of high-end hardware interfaces such as high-capacity and

high-bandwidth DDR4 SDRAM (up to 32GB), on-board USB-Blaster II, and FMC

connectors for I/O expansion, the board delivers more than 2X the performance of

previous generation development kits.

Apollo S10 is also extensible. Apollo Carrier board is designed to assist our clients’

development of Apollo S10 SoM. The carrier board features two ultra low-latency,

straight connections 40Gbps QSFP+ module and TBT3 for our clients’ to evaluate the

I/O planned for their systems, and build their custom systems around it.

1.2 Board Layout

The figures below depict the layout of the board and indicate the location of the

connectors and key components.

Apoolo-S10

User Manual

www.terasic.com

March 31, 2020

Figure 1-1 Apollo S10 board top

Apoolo-S10

User Manual

www.terasic.com

March 31, 2020

Figure 1-2 Apollo S10 board botton

1.3 Key Features

The following hardware is implemented on the Apollo S10 board:

FPGA Device

Intel Stratix ® 10 SoC FPGA : 1SX280HU2F50

2,800K logic elements (LEs)

229 Mbits embedded memory(M20K)

96 transceivers (up to 28.3Gbps)

11,520 18-bit x 19-bit multipliers

5,760 Variable-precision DSP blocks

Apoolo-S10

User Manual

www.terasic.com

March 31, 2020

FPGA Configuration

On-Board USB Blaster II for FPGA programming and Debug

AS Mode configuration from QSPI Flash

FPGA Fabric

1024Mbit QSPI Flash (EPCQL1024 Compliant)

2 on-board independent DDR4 banks

Each 16GB x72bit DDR4-2133MT/s

One bank is shared with FPGA and HPS

FMC (Vita57.1) connector with 10 transceivers

FMC VADJ 1.8V/1.5V/1.2V Selection

FMC+(Vita57.4) connector with 24 transceivers

FMC+ VADJ 1.8V/1.5V/1.2V Selection

Two 50Mhz Single-ended Clock Source

Clock Generator Si5341

LED x2, Button x2, Dip Switch x2, CPU Reset

HPS(Hard Processor System) Fabric

Quad-core 64 bit ARM Cortex-A53 MPCore* processor

MicroSD Socket

Gigabit Ethernet with RJ45

USB OTG with Micro USB Connector

UART to USB with Mini USB Connector

LED x1, Button x1, Cold Reset Button

1x6 GPIO Header

RTC

Dashboard System

Input Power Monitor

FPGA and Board Temperature Monitorl

Fan Control and Monitor

Auto Fan Speed

Auto Shutdown

Apoolo-S10

User Manual

www.terasic.com

March 31, 2020

Power Source

12V from 2x4 PCIe connector

12V from Samtec connector (reserved for carrier board)

1.3. Block Diagram

Figure 1-3 shows the block diagram of the Apollo S10 board. To provide maximum

flexibility for the users, all key components are connected to the Stratix ® 10 SX FPGA

device. Thus, users can configure the FPGAto implement any system design.

Figure 1-3 Block diagram of the Apollo S10 board

1.4. Mechanical Specifications

Figure 1-4 and Figure 1-5 are the top and bottom Mechanical Layout of Apollo S10

board. The unit of the Mechanical Layout is millimeter (mm).

Apoolo-S10

User Manual

www.terasic.com

March 31, 2020

Figure 1-4 Top side mechanical layout

Figure 1-5 Bottom side mechanical layout

Apoolo-S10

User Manual

www.terasic.com

March 31, 2020

1.5. Power Requirement

Stand-alone mode

When the Apollo S10 board is used in stand-alone mode, users can use the 12V

ATX power provided in the kit to connect to the 8-pin 12V ATX power connector

(See Figure 1-6) of the Apollo S10.

Figure 1-6 8-Pin 12V ATX Power Connector

Connect to the based board

If user wants use the Apollo S10 board as the module board and connect it to the

carrier board. The carrier board needs to provide at least 12V 15A power to the J10

power connector (See Figure 1-7) of the Apollo S10 board. Please note that the 12V

and 3.3V of the FMC and FMC + connector are provided by the Apollo S10 board, the

carrier board does not need to provide these powers. For part number of the

connector connected to J10, please refer to Table 1-1 in the section 1.6.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Terasic Microcontrollore

Manuali Microcontrollore popolari di altre marche

AMS

AMS AS7261 Demo Kit Manuale utente

Novatek

Novatek NT6861 Manuale utente

Espressif Systems

Espressif Systems ESP8266 SDK Guida all'installazione

Nuvoton

Nuvoton ISD61S00 ChipCorder Guida

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuale utente

Texas Instruments

Texas Instruments Chipcon CC2420DK Manuale utente

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuale utente

NEC

NEC 78GK0S/K 1+ Series Istruzioni per l'installazione e il funzionamento

Mikroe

Mikroe SEMITECH N-PLC Click Istruzioni per l'installazione e il funzionamento

Intel

Intel Agilex Manuale utente

Cypress

Cypress CY4607 HX2VL Manuale utente

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuale utente

Texas Instruments

Texas Instruments TMS320F2837 D Series Manuale utente

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuale utente

Texas Instruments

Texas Instruments INA-DUAL-2AMP-EVM Manuale utente

Espressif Systems

Espressif Systems ESP8266EX Istruzioni operative

Abov

Abov AC33M8128L Manuale utente

Laird

Laird BL654PA Manuale utente