TES TES-1313 Manuale utente

K/J/T/E/N/R/S

THERMOMETER

TES-1313

INSTRUCTION MANUAL

ALM LoHi

AVG-MX MN

KJTERSN

min:sec

hour:min

TYPE

INTERVAL

TES ELECTRICAL ELECTRONIC CORP.

1. INTRODUCTION

This instrument is a digital thermometer for working

with any J, K, T, E, N, R and S-type thermocouple as

temperature sensor.

Temperature indication follows the international

temperature scale of 1990. (ITS-90)

Read the following safety information carefully before

attempting to operate or service the meter.

Use the meter only as specified in this manual;

otherwise, the protection provided by the meter may

be impaired

Environment conditions

Altitude up to 2000 meters

Relatively humidity 80% max.

Operation Ambient 0～50℃(32℉~122℉)

U.S. Pat. No. Des. 446,135

Safety symbols

When servicing, use only specified replacement

parts.

Comply with EMC

2. SPECIFICATIONS

2-1 Electronical Specifications

Measurement Range :

J - type : -150.0℃to +1090.0℃(-200.0℉to +1994.0℉)

K - type : -150.0℃to +1370.0℃(-200.0℉to +1999.9℉)

T - type : -150.0℃to +400.0℃(-200.0℉to +752.0℉)

E - type : -150.0℃to +870.0℃(-200.0℉to +1598.0℉)

N - type : -150.0℃to +1300.0℃(-200.0℉to +1999.9℉)

R - type : 2.0℃to +1767.0℃(+35℉to +1999.9℉)

S - type : 2.0℃to +1767.0℃(+35℉to +1999.9℉)

Display Effect Resolution :

J-, K-, T-, E-, and N-type : 0.1℃/℉/K

R- and S-type : 1.0℃/℉/K (0.1℃/℉/K only for

reference)

Measurement Accuracy :

J-, K-, T-, E-, and N-type :

[0.05% of reading +0.5℃(0.9℉)]

[ Below -100℃(-148℉) : add 0.15% of reading for J,

K, E, and N ; and 0.45% of reading for T ]

R-and S-type : [0.05% of reading +2℃(4℉)]

NOTE

This basic accuracy specification does not include

the error of the temperature probe. Please refer

to the temperature probe accuracy specification

for additional details.

Temperature Coefficient :

0.01% of reading +0.03℃per ℃(0.06℉per ℉)

outside the specified +18℃to 28℃(+64℉to 82℉)

range.

[ Below -100℃(-148℉) : add 0.04% of reading for J-,

K-, E- and N-type ; and 0.08% of reading for T-type ]

Input Protection : 20V maximum input voltage on input

connector.

Manual Data Memory capacity : 44 sets.

2-2 General Specifications

Power Supply : 6 pcs size AAA battery.

Batterylife:approx.200hours(carbonzincbattery).

Auto Power off :30minutes.(Ifnokeyispressed).

Low Battery Indication : The ( ) is displayed when

the battery voltage drops

below the operating voltage.

Measurement Rate : One time per 1.5 seconds.

Weight : 235 gm (8.29 oz)

Dimension : 5.91”Lx 2.83”Wx 1.38”H (150x72x35mm)

Operating Temperature : 0 to 50℃(32 to 122℉)

and Humidity below 80% RH

Storage Temperature : -10 to 60℃, 14 to 140℉

and Humidity below 70% RH

Accessories: 6 pcs Battery, Instruction Manual.

3. FRONT PANEL DESCRIPTION

KJTERSN

min:sec

hour:min

TYPE

INTERVAL T1

ALM LoHi

AVG-MX MN

min:sec

hour:min

TYPE

KJTERSN

ALM

AVG

(1). LCD Display :

A. Main display : Temperature reading.

B. Secondary display :MAX, MIN, AVG reading.

C. Time display :Time display (100-hour clock),

shows elapsed time when MAX,

MIN or AVG is on.

D. Auto power off mark (:).

(2). HHOLD key : Press HHOLD key to freeze or

unfreeze the display reading.

(3). Power key : Press key to turn the meter on

or off.

(4). MX/MN key :

Press "MX/MN" key to step through the maximum,

minimum, and average readings.

Press "MX/MN" key for 2 seconds to exit MX/MN

mode.

(5). MEM key : Press "MEM" key each time, stores a

single set of logged reading in memory.

(6). SET key :

Press "SET" key to enter alarm setting mode.

Press "SET" key for 2 seconds to enter or exit

alarm mode.

(7).



Key :

Press





key to increase or decrease the

value for high/lower alarm settings.

Press or key to increase or decrease the

READ mode memory location.

(8).



key :

Press "" key to store alarm limit value setting.

Press "



" key to toggle showing the "hour : min"

and " min : sec" elapsed time in the MX/MN

mode.

(9). TYPE key: Press "TYPE" key to select the

thermocouple type (K, J, E, T, R, S,

N).

(10). READ key : Press "READ" key to show manual

memory logged reading, press

again to exit this mode.

(11). C/F/K key : Press C/F/K key to select Celsius

(℃), Fahrenheit (℉) or Kelvin (K)

temperature scale.

(12). key : Press backlight key to turn the

backlight on and off. The backlight

turns off after 13 seconds.

(13). Input : Thermocouple input.

4. OPERATION INSTRUCTIONS

WARNING

To avoid electrical shock or personal injury, do

not apply more than 20Vrms, between the

thermocouples, or between any thermocouple

and earth ground.

4-1 Temperature Measurement

Press " " key to turn on the thermometer.

Plug the thermocouple into the thermocouple input.

If no thermocouple is plugged into the selected

input or the thermocouple is "open", the display will

show "- - - -.-".

Press "C/F/K" key to the desired temperature

scale.

Press "TYPE" key to select the thermocouple you

want.

Perform measurements by contacting the object

being measured with the probe sensor.

Read the temperature on the display. The display

shows "OL" (overload) when the temperature being

measured is outside the meter valid range.

4-2 MAX, MIN and AVG Function Operations

Press "MX/MN" key to enter to MX/MN mode, to

step through the maximum (MAX), minimum (MIN)

or the true average (AVG-true 9.7 hours recording

average) readings, and disable auto power off

function.

Press "" key for 2 seconds to toggle showing the

elapsed time "hour : min" and "min : sec" on LCD.

The elapsed time since entering reading mode, or

the time at which the MAX, MIN or AVG occurred,

appears on the time display.

Press "MX/MN" key, the MAX, MIN and AVG reading

will appear on the secondary display.

TYPE

min:sec

AVG

Press "MX/MN" keyfor 2 seconds to exit MX/MN mode.

In MX/MN mode, the "C/F/K" and "TYPE" key are

not active.

4-3 To Erase the Memory of Datalogger

Press and hold down "MEN" key until the beeper

sounds twice, all memory will be cleared.

4-4 To Trigger "One by One Datalogging"

Press "MEM" key each time, stores one set logged

reading in memory, LCD shows " MEM " and

memory location numbers (01 to 44).

Press "READ" key to enter the manual memory

data mode. LCD will show " READ " and memory

location numbers.

Press ""or "" key to scroll through the logged

readings.

Press "READ" key again to exit READ mode.

TYPE

4-5 Alarm Function Operations

The ALARM function only perform on the main display

temperature value, the resolution of setting value is one

degree and regardless the temperature units.

Press "SET" key one time, enter to Alarm High limit

value setting mode, LCD will show "ALM Hi" mark.

ALM

Press ""or ""key until the display shows the

alarm High limit values you want, and then press ""

key to store the high limit value and enter to Alarm

Low limit value setting, LCD will show "ALM Lo" mark.

ALM

Press "" or "" keyuntil the displayshows the alarm

Low limit values you want, then press "" key to store

the Low limit value and finish the setting mode.

Press "SET" key for 2 seconds then release it,

enter to ALARM function LCD will show "ALM"

mark, when main display measured temperature

value exceeds the setting high temperature value

or below the setting Low temperature value, the

beeper will continuously sound.

ALM

Press "SET" key for 2 seconds then release it to

exit the ALARM function.

4-6 How to Disable Auto Power off Function

The meter will enter to the sleep mode if no key

pressed occurs for 30 minutes.

Press " " key to turn off the meter.

Press and hold down "" key then press " "

key to turn on the meter, the auto power off

function will be disabled.

The auto power off mark " : " on the time display

will disappeared.

Auto power off mode is enabled each time you

turn on the meter and is automatically.

5. MAINTENANCE

5-1 Cleaning :

Periodically wipe the case with a damp cloth and

mild detergent.

Do not use abrasives or solvents. Clean and dry

as required.

5-2 Battery Replacement :

When LCD display shows “ ”, the battery has

had insufficient power to support an accurate test.

At this moment, replace it with new battery from the

battery compartment.

6. OPTIONAL ACCESSORY

K ( CA ) type thermocouple.

Model

Range

Tolerances

Description

TP-K01

Bead

probe

-50℃to 200℃

-58℉to 392℉

2.2℃or 0.75％

(3.6℉or 0.75％)

with Teflon tape

insulation. Maximum

insulating

temperature: 260℃

TP-K02

immersion

probe

-50℃to 1000℃

-58℉to 1832℉

2.2℃or 0.75％

(3.6℉or 0.75％)

3.2φ×150 ㎜metal

sheath 100 ㎝

Compensating wire

TP-K03

Surface

probe

-50℃to 750℃

-58℉to 1382℉

2.2℃or 0.75％

(3.6℉or 0.75％)

100 ㎝Compensating

wire 12.5φx 94 ㎜

handle

TP-K01:Available for general condition, especially for

complex and any place hard to reach.

TP-K02: Available for temperature measurement of liquid,

gels or air.

TP-K03:Available for flat or curved surface measurement.

TES ELECTRICAL ELECTRONIC CORP.

7F, No. 31, Lane 513, Rui Guang Road, Neihu Dist.

Taipei.

Taiwan, R. O. C.

Tel : (02) 2799-3660 Fax : 886-2-2799-5099

E-Mail : tes@ms9.hinet.net http://www.tes.com.tw

Sep-2004-1

Indice

Altri manuali TES Termometro

TES

TES TES-1322 Manuale utente

TES

TES TES-1306 Manuale utente

TES

TES TES-1307 Manuale utente

Manuali Termometro popolari di altre marche

Delton

Delton 981A Manuale utente

Baker

Baker MM2P Manuale utente

Tarmo

Tarmo 320281 Manuale utente

Citizen

Citizen CTD 504 Manuale utente

TFA

TFA 14.1500 Manuale utente

Vive

Vive DMD1010 Manuale utente

Gotemp

Gotemp THB4002 Manuale utente

GREISINGER

GREISINGER G 1202 Manuale utente

Amprobe

Amprobe TMD-53W Manuale utente

Trotec

Trotec BP10 Manuale utente

Radiance instruments

Radiance instruments RT616 Series Manuale utente

Eurolec

Eurolec IR151 Manuale utente

Scaneo

Scaneo TS42B Manuale utente

Sper scientific

Sper scientific 800043 Manuale utente

Microlife

Microlife NC 200 Manuale di istruzioni

Motorola

Motorola MBP69SN Guida alla configurazione

The MeatStick

The MeatStick The MeatStick Manuale utente

Hama

Hama TH35-A Manuale utente