Texas Instruments Chipcon Products CC1110DK Manuale di programmazione

SWRU078A

CC1110DK Quick Start Instructions Revision 2.0, 2007-08-23

RF/Packet Error Rate Test

1. Kit Contents

•2 SmartRF04EB

•2 CC1110EM

•2 antennas

•2 USB cables

2. EB overview 3. Plug EM into EB

Insert a CC1110EM into both SmartRF04EBs.

The connectors will only fit in one position, so

that the EM cannot be inserted the wrong way.

Do not force the EM.

4a. Battery power

There are three different ways of applying

power to the EB:

The first method involves using a battery, either

a 9V or a 4xAA battery pack connected to the

battery connector on the bottom side of the

board

4b. DC power

The second method applies DC power using the DC

input jack (right in picture, centre is +, sleeve is

ground), or by connecting a 4-10V voltage source

between the 4-10V and 0V terminals of the power

connector (left in picture). It is also possible to

connect a 3.3V voltage source between the 3.3V and

0V terminals. The on-board voltage regulators will be

bypassed in this case.

4c. USB power

The EB can also be powered from the USB bus.

Make sure that the SmartRF

Studio software is

installed before connecting the EB to the PC,

otherwise you may experience problems in

installing it later due to driver issues.

Note that if multiple power sources are

connected, the source with the highest voltage

will power the EB. This means that you should

disconnect any attached battery when using a

lab supply or USB power, otherwise the battery

will be drained.

5. Set power switch

If a 3.3V source is used as described in 4b

above, the switch should be set to the leftmost

position. For all other cases, the switch should

be set to the rightmost position. This switch can

be used to turn off the EB by switching it to the

opposite position of that used to turn it on.

6. Packet error rate test

When power is applied to the board, the test

program will start. You should see the Chipcon logo

shown above on the LCD display on both EBs.

Pushing button S1 in the lower right corner of the

board will show the first menu item.

7. Select Frequency

Select frequency according to the type of EM

module in use (315 MHz, 433 MHz, 868 or 915

MHz). Move the joystick up or down to display

the choices and push button S1 in the lower

right corner of the board to select the displayed

frequency.

connectors

LCD screen

Joystick Button S1

Web sites: http://www.ti.com/lpw

TI Worldwide Support: http://www-k.ext.ti.com/sc/technical-

support/product-information-centers.htm

Technical Support Email: [email protected]

Make sure to subscribe to the Low-Power

RF Newsletter to receive information about

updates to documentation, new product

releases and more. Sign up on our web site!

Address information

SWRU078A

8. EB 1: Select Receiver

Select Receiver on the first EB by moving the

joystick. Confirm by pressing button S1. The

Receiving node will display “Ready to receive”.

9. EB 2: Select Transmitter

Select Transmitter on the other EB by moving the

joystick. Confirm by pressing button S1.

10. EB 2: Number of packets

On the transmitter EB, select the number of

packets to send. More packets takes longer but

gives a better statistical result. Confirm by

pressing button S1.

11. PER Test (Transmitter)

The transmitter will show “Transmitting!” and a

running counter that shows the number of

packets.

12. PER Test (Receiver)

The receiver will show the total accumulated

packet error rate together with the average signal

strength (RSSI) of the previous 50 received

packets.

13. Per Test results

When the PER test is completed, the result will be

displayed on the receiver until a new test is

started. A new test can be started from the

transmitter.

14. Documentation

Please visit www.ti.com to download the

CC1110DK User Manual, the SmartRF

Studio

software, examples, as well as relevant

datasheets and application notes.

If you for some reason cannot access the TI

web site and download the files, please contact

your local TI representative for assistance.

15. Troubleshooting/Notice

It you are experiencing problems with this test,

please check the following:

•Please visit

www.ti.com and enter

CC1110DK in the part number search box.

Check for updated SW and documentation.

Updated SW can be downloaded to the

device using IAR or the Flash Programmer

application.

•If results are strange at short distances, try

to move the transmitter and receiver further

apart. The CC1110 may experience

saturation when transmitting at full output

power if the units are to close.

•See “DN300 -- SmartRF04EB

Troubleshooting” for general

troubleshooting of your EB board.

SmartRF

Studio

1. Download

Before connecting the EB to your PC, download

SmartRF

Studio from www.ti.com. To find it,

type “SmartRF Studio” in the keyword search

field and click Go. Install the program.

2. Plug in EB

After the install program finishes, connect the EB

to the PC using the USB cable. Run SmartRF

Studio. Select the SmartRF

04 tab. Select the

CC1110 board, and click the Run button.

3. Configure

You can now configure the radio chip, run tests

or communicate with another EB.

Web sites: http://www.ti.com/lpw

TI Worldwide Support: http://www-k.ext.ti.com/sc/technical-

support/product-information-centers.htm

Technical Support Email: [email protected]

Make sure to subscribe to the Low-Power

RF Newsletter to receive information about

updates to documentation, new product

releases and more. Sign up on our web site!

Address information

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements,improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.Customers should obtain the latest relevant information before placing orders and should verify that such information is current andcomplete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’sstandard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support thiswarranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarilyperformed.

TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products andapplications using TI components. To minimize the risks associated with customer products and applications, customers shouldprovide adequate design and operating safeguards.TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, maskwork right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or servicesare used. Information published by TI regarding third-party products or services does not constitute a license from TI to use suchproducts or services or a warranty or endorsement thereof. Use of such information may require a license from a third party underthe patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI.Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and isaccompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is anunfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third partiesmay be subject to additional restrictions.Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or servicevoids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive businesspractice. TI is not responsible or liable for any such statements.TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product wouldreasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreementspecifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramificationsof their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-relatedrequirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding anyapplications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and itsrepresentatives against any damages arising out of the use of TI products in such safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products arespecifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet militaryspecifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade issolely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements inconnection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI productsare designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use anynon-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements.Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products Applications

Amplifiers amplifier.ti.com Audio www.ti.com/audioData Converters dataconverter.ti.com Automotive www.ti.com/automotiveDSP dsp.ti.com Broadband www.ti.com/broadbandInterface interface.ti.com Digital Control www.ti.com/digitalcontrolLogic logic.ti.com Military www.ti.com/militaryPower Mgmt power.ti.com Optical Networking www.ti.com/opticalnetworkMicrocontrollers microcontroller.ti.com Security www.ti.com/securityRFID www.ti-rfid.com Telephony www.ti.com/telephonyLow Power www.ti.com/lpw Video & Imaging www.ti.com/videoWireless

Wireless www.ti.com/wireless

Altri manuali per Chipcon Products CC1110DK

Altri manuali Texas Instruments Microcontrollore

Texas Instruments

Texas Instruments TMDSEVM6678L Manuale del prodotto

Texas Instruments

Texas Instruments LM26EVM Manuale utente

Texas Instruments

Texas Instruments LaunchPad MSP430FR2476 Manuale utente

Texas Instruments

Texas Instruments CC2540 Manuale di istruzioni

Texas Instruments

Texas Instruments TRF7970A BoosterPack Manuale utente

Texas Instruments

Texas Instruments TMUXRTJ-RRQEVM Manuale utente

Texas Instruments

Texas Instruments MSP430F67451 Manuale utente

Texas Instruments

Texas Instruments LP-EM-CC1354P10-1 Manuale

Texas Instruments

Texas Instruments Arrow IoT Manuale utente

Texas Instruments

Texas Instruments MSP430x4xx Family Manuale utente

Texas Instruments

Texas Instruments Errata MSP430F6779 Manuale utente

Texas Instruments

Texas Instruments MSP430F6745 Manuale utente

Texas Instruments

Texas Instruments MSP430F6778 Manuale utente

Texas Instruments

Texas Instruments CC3220 Manuale utente

Texas Instruments

Texas Instruments LP-MSPM0L1306 Manuale utente

Texas Instruments

Texas Instruments Serial Programming Adapter MSP430 Manuale utente

Texas Instruments

Texas Instruments TMS370 Series Guida utente

Texas Instruments

Texas Instruments C2620 Manuale del prodotto

Texas Instruments

Texas Instruments SimpleLink MSP432E4 Manuale del prodotto

Texas Instruments

Texas Instruments MSP430F6748 Manuale utente

Texas Instruments

Texas Instruments MSP430F6720A Manuale utente

Texas Instruments

Texas Instruments BoosterPack BOOSTXL-RS232 Manuale utente

Texas Instruments

Texas Instruments TM4C1294NCPDT Manuale utente

Texas Instruments

Texas Instruments MSP430G2955 Manuale utente

Manuali Microcontrollore popolari di altre marche

AMS

AMS AS7261 Demo Kit Manuale utente

Novatek

Novatek NT6861 Manuale utente

Espressif Systems

Espressif Systems ESP8266 SDK Guida all'installazione

Nuvoton

Nuvoton ISD61S00 ChipCorder Guida

STMicrolectronics

STMicrolectronics ST7 Assembler Linker Manuale utente

Lantronix

Lantronix Intrinsyc Open-Q 865XR SOM Manuale utente

NEC

NEC 78GK0S/K 1+ Series Istruzioni per l'installazione e il funzionamento

Mikroe

Mikroe SEMITECH N-PLC Click Istruzioni per l'installazione e il funzionamento

Intel

Intel Agilex Manuale utente

Cypress

Cypress CY4607 HX2VL Manuale utente

DIGITAL-LOGIC

DIGITAL-LOGIC MICROSPACE Manuale utente

CYPRES

CYPRES CY14NVSRAMKIT-001 Manuale utente

Espressif Systems

Espressif Systems ESP8266EX Istruzioni operative

Abov

Abov AC33M8128L Manuale utente

Laird

Laird BL654PA Manuale utente

Silicon Laboratories

Silicon Laboratories C8051F800 Manuale utente

Energy micro

Energy micro EFM32 Giant Gecko Starter Kit Manuale utente

Mikroe

Mikroe click Proximity 2 Manuale utente