Thermal Arc 400GTS CC/TIG Manuale utente

INVERTER

ARC

WELDER

MODEL 400GTS CC/TIG

• STICK

• TIG - HIGH FREQUENCY

- LIFT START

OPERATING MANUAL

July 1, 1997 Manual No. 0-2512

TABLE OF CONTENTS

1.0 GENERAL INFORMATION ........................................................2

1.01 Notes, Cautions and Warnings .................................................2

1.02 Important Safety Precautions....................................................3

1.03 Publications .................................................................................6

1.04 Note, Attention et Avertissement .............................................7

1.05 Precautions De Securite Importantes.......................................8

1.06 Documents De Reference......................................................... 11

1.07 Declaration of Conformity ......................................................12

1.08 Statement of Warranty .............................................................13

2.0 INTRODUCTION AND DESCRIPTION................................15

2.01 Description ................................................................................15

2.02 Functional Block Diagram.......................................................16

2.03 Transporting Methods..............................................................17

2.04 Electrical Input Connections ...................................................17

2.05 Specifications.............................................................................20

2.06 Duty Cycle .................................................................................21

3.0 OPERATOR CONTROLS ...........................................................22

3.01 Front and Rear operator controls ...........................................22

3.02 Setup for Operation ..................................................................24

Shielded Metal Arc Welding (SMAW) .........................................25

Gas Tungsten Arc Welding (GTAW)

High Frequency/Lift Start.............................................................26

Gas Tungsten Arc Welding-Pulsed (GTAW-P)

-Sloped (GTAW-S) -TIG Spot .........................................................28

4.0 BASIC TROUBLESHOOTING..................................................31

4.01 Common Welding Operation Faults......................................31

4.02 Specific Problems......................................................................31

4.03 Remote 8-Pin Connections ......................................................35

APPENDIX A – ACCESORIES.........................................................36

APPENDIX B – INTERCONNECTION DIAGRAMS.................39

1GENERALMANUAL 0-2512

WARNING Read and understand this entire Operating Manual and your

employer’s safety practices before installing, operating, or servicing

the equipment.

WARNING While the information contained in this Operating Manual represents

our best judgement, Thermal Dynamics Corporation assumes no

liability for its use.

Thermal Arc Models 400GTS CC/TIG Welder

Operating Manual Number 0-2512

Published by:

Thermal Dynamics Corporation

Industrial Park No. 2

West Lebanon, New Hampshire, USA 03784

(603) 298-5711

Thermal Dynamics Corporation

Reproduction of this work, in whole or in part, without written

permission of the publisher is prohibited.

The publisher does not assume and hereby disclaims any liability to any

party for any loss or damage caused by any error or omission in this

Operating Manual, whether such error results from negligence,

accident, or any other cause.

Printed in the United States of America

July 1, 1997

GENERAL MANUAL 0-2512

1.0 GENERAL INFORMATION

1.01 NOTES, CAUTIONS AND WARNINGS

Throughout this manual, notes, cautions, and warnings are used to

highlight important information. These highlights are categorized as

follows:

NOTE An operation, procedure, or background information which requires

additional emphasis or is helpful in efficient operation of the system.

CAUTION A procedure which, if not properly followed, may cause damage to the

equipment.

WARNING A procedure which, if not properly followed, may cause injury to the

operator or others in the operating area.

3GENERALMANUAL 0-2512

WARNING

1.02 IMPORTANT SAFETY PRECAUTIONS

OPERATION AND MAINTENANCE OF PLASMA ARC EQUIPMENT

CAN BE DANGEROUS AND HAZARDOUS TO YOUR HEALTH.

To prevent possible injury, read, understand and follow all warnings, safety precautions and

instructions before using the equipment. Call 1-603-298-5711 or your local distributor if you have any

questions.

GASES AND FUMES Gases and fumes produced during the plasma cutting process can be

dangerous and hazardous to your health.

• Keep all fumes and gases from the breathing area. Keep your head out

of the welding fume plume.

• Use an air-supplied respirator if ventilation is not adequate to remove

all fumes and gases.

• The kinds of fumes and gases from the plasma arc depend on the kind

of metal being used, coatings on the metal, and the different

processes. You must be very careful when cutting or welding any

metals which may contain one or more of the following:

Antimony Chromium Mercury

Arsenic Cobalt Nickel

Barium Copper Selenium

Beryllium Lead Silver

Cadmium Manganese Vanadium

• Always read the Material Safety Data Sheets (MSDS) that should be

supplied with the material you are using. These MSDSs will give you

the information regarding the kind and amount of fumes and gases

that may be dangerous to your health.

• For information on how to test for fumes and gases in your

workplace, refer to item 1 in the Publications Section in this manual.

• Use special equipment, such as water or down draft cutting tables, to

capture fumes and gases.

• Do not use the plasma torch in an area where combustible or

explosive gases or materials are located.

• Phosgene, a toxic gas, is generated from the vapors of chlorinated

solvents and cleansers. Remove all sources of these vapors.

GENERAL MANUAL 0-2512

IMPORTANT SAFETY PRECAUTIONS (CONTINUED)

ELECTRIC SHOCK Electric Shock can injure or kill. The plasma arc process uses and

produces high voltage electrical energy. This electric energy can cause

severe or fatal shock to the operator or others in the workplace.

• Never touch any parts that are electrically “live” or “hot.”

• Wear dry gloves and clothing. Insulate yourself from the work piece

or other parts of the welding circuit.

• Repair or replace all worn or damaged parts.

• Extra care must be taken when the workplace is moist or damp.

• Install and maintain equipment according to NEC code, refer to item 4

in the Publications section of this manual.

• Disconnect power source before performing any service or repairs.

• Read and follow all the instructions in the Operating Manual.

FIRE AND EXPLOSION Fire and explosion can be caused by hot slag, sparks, or the plasma arc.

• Be sure there is no combustible or flammable material in the

workplace. Any material that cannot be removed must be protected.

• Ventilate all flammable or explosive vapors from the workplace.

• Do not cut or weld on containers that may have held combustibles.

• Provide a fire watch when working in an area where fire hazards may

exist.

• Hydrogen gas may be formed and trapped under aluminum

workpieces when they are cut underwater or while using a water

table. DO NOT cut aluminum alloys underwater or on a water table

unless the hydrogen gas can be eliminated or dissipated. Trapped

hydrogen gas that is ignited will cause an explosion.

NOISE Noise can cause permanent hearing loss. Plasma arc processes can cause

noise levels to exceed safe limits. You must protect your ears from loud

noise to prevent permanent loss of hearing.

• To protect your hearing from loud noise, wear protective ear plugs

and/or ear muffs. Protect others in the workplace.

• Noise levels should be measured to be sure the decibels (sound) do

not exceed safe levels.

• For information on how to test for noise, see item 1 in the Publications

section of this manual.

5GENERALMANUAL 0-2512

IMPORTANT SAFETY PRECAUTIONS (CONTINUED)

PLASMAARC RAYS Plasma Arc Rays can injure your eyes and burn your skin. The plasma

arc process produces very bright ultra violet and infra red light. These

arc rays will damage your eyes and burn your skin if you are not

properly protected.

• To protect your eyes, always wear a welding helmet or shield. Also

always wear safety glasses with side shields, goggles or other

protective eye wear.

• Wear welding gloves and suitable clothing to protect your skin from

the arc rays and sparks.

• Keep helmet and safety glasses in good condition. Replace lenses

when cracked, chipped or dirty.

• Protect others in the work area from the arc rays. Use protective

booths, screens or shields.

• Use the shade of lens as recommended in the Operating Manual.

6GENERAL MANUAL 0-2512

1.03 PUBLICATIONS

Refer to the following standards or their latest revisions for more information:

1. OSHA, SAFETY AND HEALTH STANDARDS, 29CFR 1910, obtainable from the Superintendent

of Documents, U.S. Government Printing Office, Washington, D.C. 20402

2. ANSI Standard Z49.1, SAFETY IN WELDINGAND CUTTING, obtainable from the American

Welding Society, 550 N.W. LeJeune Rd, Miami, FL 33126

3. NIOSH, SAFETY AND HEALTH IN ARC WELDING AND GAS WELDINGAND CUTTING,

obtainable from the Superintendent of Documents, U.S. Government Printing Office,

Washington, D.C. 20402

4. ANSI Standard Z87.1, SAFE PRACTICES FOR OCCUPATION AND EDUCATIONAL EYE AND

FACE PROTECTION, obtainable from American National Standards Institute, 1430 Broadway,

New York, NY 10018

5. ANSI Standard Z41.1, STANDARD FOR MEN’S SAFETY-TOE FOOTWEAR, obtainable from the

American National Standards Institute, 1430 Broadway, New York, NY 10018

6. ANSI Standard Z49.2, FIRE PREVENTION IN THE USE OF CUTTING AND WELDING

PROCESSES, obtainable from American National Standards Institute, 1430 Broadway, New York,

NY 10018

7. AWS StandardA6.0, WELDING AND CUTTING CONTAINERS WHICH HAVE HELD

COMBUSTIBLES, obtainable from American Welding Society, 550 N.W. LeJeune Rd, Miami, FL

33126

8. NFPAStandard 51, OXYGEN-FUEL GAS SYSTEMS FOR WELDING, CUTTING AND ALLIED

PROCESSES, obtainable from the National Fire Protection Association, Batterymarch Park,

Quincy, MA 02269

9. NFPAStandard 70, NATIONAL ELECTRICAL CODE, obtainable from the National Fire

Protection Association, Batterymarch Park, Quincy, MA 02269

10. NFPAStandard 51B, CUTTING AND WELDING PROCESSES, obtainable from the National Fire

Protection Association, Batterymarch Park, Quincy, MA 02269

11. CGA Pamphlet P-1, SAFE HANDLING OF COMPRESSED GASES IN CYLINDERS, obtainable

from the Compressed Gas Association, 1235 Jefferson Davis Highway, Suite 501, Arlington, VA

22202

12. CSA Standard W117.2, CODE FOR SAFETY IN WELDING AND CUTTING, obtainable from the

Canadian Standards Association, Standards Sales, 178 Rexdale Boulevard, Rexdale, Ontario,

Canada M9W 1R3

13. NWSA booklet, WELDING SAFETY BIBLIOGRAPHY obtainable from the National Welding

Supply Association, 1900 Arch Street, Philadelphia, PA 19103

14. American Welding Society StandardAWSF4.1, RECOMMENDED SAFE PRACTICES FOR THE

PREPARATION FOR WELDING AND CUTTING OF CONTAINERS AND PIPING THAT HAVE

HELD HAZARDOUS SUBSTANCES, obtainable from the American Welding Society, 550 N.W.

LeJeune Rd, Miami, FL 33126

15. ANSI Standard Z88.2, PRACTICE FOR RESPIRATORY PROTECTION, obtainable from

American National Standards Institute, 1430 Broadway, New York, NY 10018

7GENERALMANUAL 0-2512

1.04 NOTE, ATTENTION ET AVERTISSEMENT

Dans ce manuel, les mots “note,” “attention,” et “avertissement” sont

utilisés pour mettre en relief des informations à caractère important. Ces

mises en relief sont classifiées comme suit :

NOTET oute opération, procédure ou renseignement général sur lequel il

importe d’insister davantage ou qui contribue à l’efficacité de

fonctionnement du système.

ATTENTION Toute procédure pouvant résulter l’endommagement du matériel en cas

de non-respect de la procédure en question.

AVERTISSEMENT Toute procédure pouvant provoquer des blessures de l’opérateur

ou des autres personnes se trouvant dans la zone de travail en cas de

non-respect de la procédure en question.

GENERAL MANUAL 0-2512

AVERTISSEMENT

1.05 PRECAUTIONS DE SECURITE IMPORTANTES

L’OPÉRATION ET LA MAINTENANCE DU MATÉRIEL DE SOUDAGE

À L’ARC AU JET DE PLASMA PEUVENT PRÉSENTER

DES RISQUES ET DES DANGERS DE SANTÉ.

Il faut communiquer aux opérateurs et au personnel TOUS les dangers possibles. Afin d’éviter les

blessures possibles, lisez, comprenez et suivez tous les avertissements, toutes les précautions de

sécurité et toutes les consignes avant d’utiliser le matériel. Composez le + 603-298-5711 ou votre

distributeur local si vous avez des questions.

FUMÉE et GAZ La fumée et les gaz produits par le procédé de jet de plasma peuvent

présenter des risques et des dangers de santé.

• Eloignez toute fumée et gaz de votre zone de respiration. Gardez votre

tête hors de la plume de fumée provenant du chalumeau.

• Utilisez un appareil respiratoire à alimentation en air si l’aération

fournie ne permet pas d’éliminer la fumée et les gaz.

• Les sortes de gaz et de fumée provenant de l’arc de plasma dépendent

du genre de métal utilisé, des revêtements se trouvant sur le métal et

des différents procédés. Vous devez prendre soin lorsque vous coupez

ou soudez tout métal pouvant contenir un ou plusieurs des éléments

suivants:

antimoine cadmium mercure

argent chrome nickel

arsenic cobalt plomb

baryum cuivre sélénium

béryllium manganèse vanadium

• Lisez toujours les fiches de données sur la sécurité des matières (sigle

américain “MSDS”); celles-ci devraient être fournies avec le matériel

que vous utilisez. Les MSDS contiennent des renseignements quant à

la quantité et la nature de la fumée et des gaz pouvant poser des

dangers de santé.

• Pour des informations sur la manière de tester la fumée et les gaz de

votre lieu de travail, consultez l’article 1 et les documents cités à la

page 11.

• Utilisez un équipement spécial tel que des tables de coupe à débit

d’eau ou à courant descendant pour capter la fumée et les gaz.

• N’utilisez pas le chalumeau au jet de plasma dans une zone où se

trouvent des matières ou des gaz combustibles ou explosifs.

• Le phosgène, un gaz toxique, est généré par la fumée provenant des

solvants et des produits de nettoyage chlorés. Eliminez toute source

de telle fumée.

Indice

Altri manuali Thermal Arc Sistema di saldatura

Thermal Arc

Thermal Arc 250S DC CC Manuale utente

Thermal Arc

Thermal Arc FABRICATOR 210 Manuale utente

Thermal Arc

Thermal Arc 211i Manuale utente

Thermal Arc

Thermal Arc 251 FABRICATOR Manuale utente

Thermal Arc

Thermal Arc 161 S Manuale utente

Thermal Arc

Thermal Arc 300GTSW Pro-Wave Manuale utente

Thermal Arc

Thermal Arc 202 AC/DC Manuale utente

Thermal Arc

Thermal Arc 400S Manuale utente

Thermal Arc

Thermal Arc POWERMASTER 350P Manuale utente

Thermal Arc

Thermal Arc 161 S Manuale utente

Thermal Arc

Thermal Arc POWERMASTER 320SP Manuale utente

Thermal Arc

Thermal Arc 400S Manuale utente

Thermal Arc

Thermal Arc 400MSTW CC Manuale utente

Thermal Arc

Thermal Arc 281 FABRICATOR Manuale utente

Thermal Arc

Thermal Arc Viking 210GM Manuale utente

Thermal Arc

Thermal Arc 251 FABRICATOR Manuale utente

Thermal Arc

Thermal Arc 161 S Manuale utente

Thermal Arc

Thermal Arc PAK 20A Manuale utente

Thermal Arc

Thermal Arc PS-3000 Manuale utente

Thermal Arc

Thermal Arc A-07360 Manuale utente

Thermal Arc

Thermal Arc EXCEL-ARC 750 CC Manuale utente

Thermal Arc

Thermal Arc POWERMASTER 400SP Manuale utente

Thermal Arc

Thermal Arc 250GTSWSE Manuale utente

Thermal Arc

Thermal Arc ARCMASTER 300S Manuale utente

Manuali Sistema di saldatura popolari di altre marche

Berner

Berner PLASMACUT 54 Manuale utente

Pro Spot

Pro Spot PR-155 Manuale utente

Forney

Forney 210 Manuale utente

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuale utente

GYS

GYS PROTIG 201 AC/DC Manuale utente

TAFA

TAFA 30*8B35 Manuale utente

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuale utente

ESAB

ESAB Buddy Arc 145 Manuale utente

CIGWELD

CIGWELD 636804 Guida rapida

Red-D-Arc

Red-D-Arc DC-400 Manuale utente

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuale utente

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuale utente

WIA

WIA Weldmatic 270 CP132-2 Manuale utente

Sonics

Sonics H520T Manuale utente

Miller

Miller Big Blue 400D Manuale utente

NewArc

NewArc RT2000 Guida rapida

Hypertherm

Hypertherm powermax1000 Manuale utente

Lincoln Electric

Lincoln Electric POWER WAVE I400 Manuale utente