Thitronik WiPro III Manuale utente
Revision 1. 6
Thitronik GmbH
g
–
Ec
fö
Installation manual for WiPro III Page 1
GB
Chapter Page Contents
1 Installing the system
1.1 1 Functional description
1.2 2 Installation instructions
1.3 2 Specialfeaturesspecictothevehicle
1.4 3 Accessories
1.5 3 Special functions (volume, anti-jamming)
1.6 4 Preparing for installation
1.7 4 Adjusting WiPro to the vehicle type
1.8 5 Storing wireless components
1.9 5 Deleting wireless components
1.9.1 6 Diagrams
1.9.2 7 Installing the wireless magnetic contacts
1.9.3 7 Rangetest/Diagnosticsmode
1.9.4 7 Installing the wireless gas alarm (accessory)
1.9.5 8 Diagrams
1.9.6 9 Installing the radio cable loop (accessory)
1.9.7 9 Installing and connecting external sirens (accessories)
1.9.8 9 Installing the central unit
1.9.9 10 CAN bus diagnostics
1.9.10 10 Performing an alarm test
2 10 – 15 Connecting the central unit to the vehicle systems
3 Miscellaneous
3.1 16 Technicalspecications
3.2 16 Approvals
3.3 16 Scope of delivery
3.4 17 Troubleshooting/Support
3.5 18 Disposal instructions
1.1 Functional description
The WiPro III alarm system has been developed especially for recreational vehicles.
This system does not use motion sensors, which have to be deactivated when the
vehicle is staying somewhere and are often the cause of false alarms. The result is
a thoroughly user-friendly alarm system which is operated at the touch of a button
and is practically immune to false alarms.
The interior is secured via wireless magnetic contacts on the doors, windows and
hatches. All doors, sliding doors, rear doors and, if necessary, the front lid monitored
by the CAN bus are secured by the CAN bus connection.
The cab doors on vehicles without a CAN bus are secured by the interior lighting.
The system is operated via the original remote key fob or the Thitronik wireless
remote control, depending on the vehicle concerned. If a secured opening is opened
while the alarm system is armed, WiPro (if properly connected) will indicate this by
switching on the integrated siren, sounding the horn (not with all vehicle types) and
activating the hazard indicators. The alarm is active for the legally permissible period
of 30 seconds for the horn and siren and 120 seconds for the hazard indicators. After
expiration of the legally stipulated maximum duration, WiPro III is automatically
armed again.
GB
Installation manual for WiPro III Page 2
1.3 Special features specic to the vehicle
General:Allvehicledoorswhicharemonitoredbythevehiclecomputerrequireno
wireless magnetic contact, since these doors are automatically secured via the CAN
bus when the WiPro unit is properly connected to the vehicle system. This is also the
case with fully integrated vehicles in which the body manufacturer has connected the
door contacts of the basic vehicle.
This is the case if an opened door is displayed on the multi-purpose display.
For some vehicle types (e.g., Sprinter, T5, T6), the horn will only operate when the
ignition is on. The vehicle horn is not triggered by WiPro III in this case. It is
recommended to mount a siren in the engine compartment or to use a back-up siren.
Further information:
http://www.thitronik-automotive.de/en/support/faqs/faq-wipro-iii.html
1.2 Installation instructions
When working on the vehicle electrical system and there is a risk of a short
circuit, the minus pole of the battery must be disconnected. The minus pole
of additional supply batteries must also be disconnected.
Note! When the vehicle battery is disconnected, some of the data from the
vehicle electronic system will be lost. Make sure that you have the radio code
because this will have to be re-entered. Data such as the time are volatile and
must also be re-entered.
Parts which are mounted on the vehicle must be fastened down so they do not
come adrift due to vibrations, sudden braking or other conditions and block vehicle
functions such as the steering system and pedals etc.
Cables must be protected from wearing through or other mechanical stress by
using appropriate fasteners to secure them.
Whenever working on the vehicle, always follow the safety and working
instructions stipulated by the vehicle manufacturer and vehicle trade.
Please read this installation manual carefully to avoid problems during installation.
Incorrect installation can damage both the alarm system and the vehicle. If problems
occur during installation, we will be glad to assist you.
However, assistance is possible only if you have read and understood this manual
completelyandifyouaresucientlyqualiedtoinstallthesystem.
Specialist dealers can obtain vehicle-specic installation documents with precise
specications for connecting the CAN bus, smart indicators, horn and central locking
system evaluation and much more on request. These contain the pin assignments on
the vehicle connectors and the position of the components.
Installation manual for WiPro III Page 3
GB
1.4 Accessories
Also available as accessories are additional wireless magnetic contacts, wireless
remote controls, radio cable loops, wireless gas alarms and a GSM telemetry module
(Pro-nder)forvehicletracking.
By using other wireless magnetic contacts (Item no: 100757 black, 100758
white),itispossibletosecurebaeplates,windows,doors,roofhatchesandeven
roof boxes.
Wireless remote controls (Item: 100756) enable other family members etc.
to control the system and gain access to the vehicle.
By using the radio cable loop (Item no: 100761), you can secure mobile goods
(such as bicycles, motor scooters, surfboards and camping furniture etc.) against
theft outside the vehicle.
By using one or more wireless gas alarms (Item no: 100759), you can protect
your gas supply from the threat of gas leaks and attacks with narcotic gases. The gas
alarm immediately signals the presence of dangerous gases in the room air to the
WiPro, which, in turn, gives out an alarm.
Pro-nder (Item no: 100699) sends an SMS to up to 10 programmable telephone
numbers in the event of an alarm. Another safety function is that when the supply
battery reaches a critical state, an SMS is dispatched with the latest battery voltage.
Theair-conditioningsystemorheateretc.canalsobeswitchedonoroviaan
SMS.ThealarmsystemcanalsobeswitchedonoroviaanSMS.Statusenquiries
requestinginformationonthestatusoftheWiProandthebatterystateetc.canbe
sent at any time by calling the Pro-nder.
The integrated GPS receiver makes it possible to locate a stolen vehicle.
If the vehicle is stolen, an alarm SMS with information on the vehicle location
and speed is dispatched automatically.
BycallingthePro-nder,thestatusenquirywhichlikewisecontainstheposition,
speed and battery state etc. can also be activated at any time.
1.5 Special functions
Reducing the volume of the internal siren:
To reduce the volume, set switch 8 of the DIP switch (A) to the ON position as shown
in Diagram 2 on Page 6.
Disabling the anti-jamming alarm:
IfyoufrequentlyuseyourvehicleinareaswheretheWiProIIIisexposedtoillegal
traconitstransmissionfrequency,thismayresultinundesiredalarms.
To disable the anti-jamming alarm function, set switch 7 of the DIP switch (A) to the
ON position as shown in Diagram 2 on Page 6.
Protection against “replay attacks”
(possiblefromserialno:0823-014orrmwareversion5.8)
To prevent the control of the WiPro III via the car key, set switch 5 of the DIP switch
(A) in sketch 2 on page 6 to position ON.
The evaluation of the vehicle doors nevertheless takes place.
Installation manual for WiPro III Page 4
GB
1.6 Preparing for installation
Make sure you have the tools and materials listed below:
- Cross-head screwdriver - Crimping pliers
- Voltmeter - Cordless screwdriver
- 8mm drill bit - Socket set
- Insulating tape - Butt connectors
- Ring terminals - Cable ties
- Shrink sleeve if necessary - Cleaning cloth for degreasing
- Cleaning agent or degreaser
Choose a suitable place for installing the central unit, the wireless magnetic contact(s)
and other accessories.
Accessories such as the wireless magnetic contacts, wireless gas alarm and
radio cable loop should be assigned prior to installation. (see 1.8)
1.7 Adjusting WiPro to the vehicle type
Open the casing of the central unit (A) by gently levering up the casing cover as shown
in Diagram 1 on Page 6.
Set the DIP switch (A) in Diagram 2, Page 6 according to Table 1. If your vehicle is
not on the list or older, connect it in the usual way (see universal connection diagram,
Page 11) and make sure that switches 1–4 are in the o position.
The settings must be made with the circuit de-energised. Make sure that neither
the20-pinplugnortheplugforthePro-nderarepluggedin.
Table 1
Other types of vehicles can be found at www.thitronik-automotive.de/en/support/faqs/faq-wipro-iii.html
Vehicles from 2006
and later Years of
manu-
facture
Switch 1 Switch 2 Switch 3 Switch 4
Fiat Ducato
Citroen Jumper
Peugeot Boxer
Iveco Daily
2006
and later o on o o
Ford Transit 2006
and later on on o o
Mercedes Sprinter
VW Crafter 2006
and later on o o o
Renault Master
Opel Movano
Nissan Interstar
2006
to 2011 on on on o
New Renault Master 2011
and later o on on o
VW T5 2006
to 2009 on o on o
VW T5 Facelift 2010
and later on o o on
Installation manual for WiPro III Page 5
GB
1.8 Storing wireless magnetic contacts, wireless remote controls, etc.
!! As supplied, no wireless magnetic contacts, etc. are stored !!
If the instructions in this chapter are not carried out, the alarm system can-
not interpret the signals transmitted by the wireless components, and the
wireless components cannot trigger an alarm.
Plug in the 20-pin plug “A” (Diagram 1, Page 6).
Now, hold down the button “B” on the front of the casing (Diagram 1, Page 6)
until the central unit gives a long beep and the status LED comes on.
Another option is to activate Assign mode as described in the operating instructions.
Now activate each wireless magnetic contact to be stored as shown in Diagram 4
(keepingbothpartsawayfromeachotheruntiltheLED(“C”)lightsupbriey).
Or press one of the buttons on the wireless remote control as shown in Diagram 5.
The wireless gas alarms must be switched on to store them and radio cable loops
must be removed from the holder.
After each storing procedure has been successfully carried out, a short beep will
sound,andthestatusLEDwillgooutbriey.
ToterminateAssignmode,brieypressthebutton“B”onthefrontofthecasing
again. The central unit will sound a double beep, and the status LED will go out.
1.9 Deleting wireless components
Transmitters can only be deleted by erasing the memory.
Hold down the button “B” on the front of the casing (Diagram 1 on Page 6) while
unplugging the 20-pin plug until the central unit gives a long beep. All the transmit-
ters are now erased.
Important!
The procedure for subsequently adding wireless components, without access
to the main unit, is described in Chapter 2 of the Operating Instructions.
Installation manual for WiPro III Page 6
GB
Diagram 1 Diagram 2
A
Diagram 3 Diagram 4
Diagram 5
B
A
1.9.1 Diagrams
max. 22 mm
ABAB
C
<<<>>>
GSM module
connection
Common pin 2
Common pin 3
indicator input
NO (COM)
Antenna
Horn
Ignition
Hazard indicators
external LED
(gnd
)
external LED +
NO
–12V (gnd)
Right indicator
Left indicator
Siren + 12 V
Siren gnd
CAN high
CAN low
+12V DC
Common pin 1
Diagram 6
C
Installation manual for WiPro III Page 7
GB
1.9.2 Installing the wireless magnetic contacts
Choose the places where you want to install the wireless magnetic contacts.
The transmitters can be installed both on the window and the frame (see diagrams
on Page 8). The distance between the transmitter (Diagram 3, Part A, Page 6)
and magnet (Diagram 3, Part B, Page 6) can be around 22 mm. A larger distance
activatesthetransmissionprocess(LEDlightsupbriey.Diagram4,C)andtriggers
the alarm when the system is activated.
Before installing the wireless magnetic contacts, carry out a range test using the
adhesive pads.
Inordertodoso,xthetransmitterwhichisalreadyassignedandthemagnets
to the places you have chosen using adhesive tape and follow the instructions
under 1.9.3.
The contact surface must be clean, dry and free of grease. Treat with suitable
cleaning agent beforehand.
Donotuseonsurfacesattemperaturebelow15°C.
Theadhesivepadsreachtheirnalstrengthafterapprox.24hours.
If installed on the rear storage locker, use the mounting adapter
(Item no. 100428 black or 100729 white) to optimize the transmission
and bridge larger gaps.
1.9.3 Range test / Diagnostics mode
Brieypressthebutton“B”onthecentralunit(Diagram1Page6).ThestatusLED
onthecableassemblystartstoash.WiProIIIisnowinDiagnosticmode.
The central unit acknowledges every transmission process received from
an assigned transmitter with an acoustic signal.
If there is no acoustic acknowledgement tone, the transmitter is not assigned
(repeat 1.8) or shielded by metal parts. In this case, choose another place to mount
the transmitter or use the mounting adapter (Item no. 100428 or 100729).
ToterminateDiagnosticsmode,brieypressthebutton“A”again.
The LED goes out.
1.9.4 Installing the wireless gas alarm (accessory)
Choose a suitable place to mount the wireless gas alarm.
The place where it is mounted should not be in the direct vicinity of the heater
outlets or where there are lead-acid batteries. Mounting it in the direct vicinity
of strong cleaning agents, petrol and other fuels should also be avoided.
The ideal height of installation is at the lowest point of the vehicle just above the
oor(approx.10–20cm).
Now carry out a range test with the wireless gas alarm, as described under 1.9.3.
Mount the wireless gas alarm using the template in the wireless gas alarm manual
andconnectthesupplyvoltage.(brown=+12V/white=earth)
Installation manual for WiPro III Page 8
GB
1.9.5 Diagrams
Option lying
on the right
It is possible to mount the transmitter
casing in a lying position (on the left or,
rotated180°,ontheright)orstanding
on the side – depending on the frame
andtheavailablespace/thedistances
to the pane. When the transmitter
casing is rotated, the circuit board with
the transmit LED, the reed sensor and
the transmitter cover will keep their
orientation to the magnet.
Option
standing
Option lying
on the left
Window frame
Window pane
Window pane
For instance, Dometic AGP7 or Seitz AGS5
and similar products
Window frame
Window pane
Option
window pane
If the available space does not allow for the transmitter
to be installed on the window frame, the transmitter
can also be mounted on the window pane as shown
on the right.
If installation is not possible using the included adhesive
pads,youcanalsousescrewstoxthetransmitter
housinginplace.Youwillndscrewpositionmarks
underneath the circuit board.
Please scan the QR code for additional
information and video instructions.
www.thitronik-automotive.de/support.html
Transmit LED
Reed sensor
Transmitter casing Magnet
Transmitter
cover
Window frame
Window pane
Window frame
Installation manual for WiPro III Page 9
GB
1.9.6 Installing the radio cable loop (accessory)
Choose a suitable place for installation at the back of the vehicle or on one of the
sides. You can also obtain further holders as accessories (Item no: 100649) to use
the cable loop for other areas of the vehicle.
Now carry out a range test with the radio cable loop, as described under 1.9.3.
Removing the cable loop from the holder triggers a transmission process.
Using the screws provided, fasten the holder of the cable loop to where you want
to place it. If you drill through the outer skin of the vehicle, seal the drilled holes
withSikaextopreventthepenetrationofmoisture.
1.9.7 Installing and connecting external sirens (accessories)
Choose a suitable place for mounting in the vehicle interior or in the engine
compartment. When laying the cable, make sure that it does not lie within the range
ofmovementofanymovingpartsofthevehicle,thatitleavessucientdistancefrom
hot engine components and cannot be exposed to wear damage due to sharp edges.
The siren must not be detached through vibration, braking suddenly or other condi-
tions and thereby impede the roadworthiness of the vehicle. As with the cables, the
sirenmustbesucientlyfarawayfromhotenginecomponents.
Siren without rechargeable battery
Connecttheredandtheblackcableofthesirentothewhite(Pin15/siren+12V)and
thewhite/blackcableofthecableassembly,respectively.
Back-up siren with rechargeable battery
The back-up siren has an integrated rechargeable battery which is constantly charged
via the red (+12 V) and black (earth) conductors. These conductors must be connect-
ed to the on-board power supply. The back-up siren sounds if there is a power failure
(only when it is activated via the key switch).
The white wire of the back-up siren must be connected to the white wire of the central
unit(Pin15/siren+12V).Thebluewire(negativetrigger)oftheback-upsirenisnot
used (please insulate it). The back-up siren sounds when there is a positive voltage
on the white wire (only when it is activated via the key switch).
1.9.8 Installing the central unit
Choose a suitable place in the vehicle interior to mount the central unit where the
unitisprotectedagainstquickaccess.Ideally,chooseaplaceforinstallingitnearto
the central electronic unit of the vehicle in order to keep the cable lengths as short
as possible. You can use both the provided adhesive pads or the plastic parts, which
are also included, to mount the unit. You need to apply some adhesive to the plastic
angesbeforeyoucanxthemtothecasing.Whenlayingthecables,makesurethat
they are not within the range of movement of moving parts of the vehicle or pedals
etc.
Altri manuali per WiPro III
3
Indice
Altri manuali Thitronik Sistema di sicurezza
Thitronik
Thitronik C.A.S. III Istruzioni operative
Thitronik
Thitronik G.A.S.-pro III Manuale utente
Thitronik
Thitronik Power Alarm System Manuale utente
Thitronik
Thitronik G.A.S.-pro Manuale utente
Thitronik
Thitronik WiPro III Manuale utente
Thitronik
Thitronik GBA-I Manuale utente
Thitronik
Thitronik THA-2-00015 Manuale utente
Manuali Sistema di sicurezza popolari di altre marche
EDM
EDM Solution 6+6 Wireless-AE Manuale utente
Highway Safety Group
Highway Safety Group EA401 Manuale utente
Siren
Siren LED GSM Manuale utente
Detection Systems
Detection Systems 7090i Istruzioni per il montaggio
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuale utente
Siemens
Siemens FDM273 Manuale utente