THOMSON 512269 Manuale utente
www.mythomson.com
V1
EN Smart video intercom
Smart Connect
512269
105°
Visitors memory
(video or pictures)
105°
Visitors memory
(video or pictures)
2
VIDEOPHONE SMART CONNECT
EN 2
www.mythomson.com
15V +
1
3
2
4
100m max
25m
max
25m
max
Figure 1
Connection from the intercom panel to the monitor
Connecting of the dry contact (gate automation) or electric strike plate to the intercom panel
Cable length
Cable length
0 to 25m
5 to 50 m
50 to 100m
Section to use
Section to use
0.75mm2
0.75mm2
1.5mm2
3EN
EN
www.mythomson.com
VIDEOPHONE SMART CONNECT
Figure 2
15V +
1
3
2
4
15V +
1
3
2
4
100m max
Moniteur supplémentaire (512264)
25m
max
25m
max
VIDEOPHONE SMART CONNECT
EN 4
www.mythomson.com
TABLE OF CONTENTS
A - SAFETY INSTRUCTIONS 07
1 - INTRODUCTION 07
2 - MAINTENANCE AND CLEANING 07
3 - RECYCLING 07
B- PRODUCT DESCRIPTION 08
1 - KIT CONTENTS 08
2 - GENERAL INFO 08
3 - MONITOR 08
4 - INTERCOM PANEL 09
5 - WALL BRACKET 09
6 - MAINS ADAPTOR 09
C - INSTALLATION 10
1 - WIRING 10
1.1 - Connecting the videophone (monitor, intercom panel and camera) 10
1.2 - Connecting a gate motor 10
1.3 - Connecting an electric strike plate or lock 10
2 - CONFIGURATION OF THE INTERCOM PANEL 10
2.1 - Setting the volume of the intercom panel 10
2.2-CongurationoftheRFIDfunction 10
2.2.1. Programming (or resetting) the administrator badges 10
2.2.2. Add one or more user badges 11
2.2.3. Remove one or more user badges 11
2.2.4. Remove all user badges 11
2.2.5. Use of badges 11
2.2.6. Replacing a badge 11
3 - INSTALLING THE SMART BRACKET 11
4 - DIAGNOSTICS AND INSTALLATION 12
5 - INSTALLATION OF THE MAIN OR ADDITIONAL INTERCOM PANEL 13
6 - SMARTPHONE APPLICATION 13
6.1 - Connecting a monitor to the WiFi network 13
F - TECHNICAL AND LEGAL INFORMATION 16
1 - GENERAL CHARACTERISTICS 16
2 - WARRANTY 17
3 - HELP AND ADVICE 17
4 - PRODUCT RETURNS/AFTER-SALES SERVICE 17
5 - EC DECLARATION OF CONFORMITY 17
7EN
EN
www.mythomson.com
VIDEOPHONE SMART CONNECT
A - SAFETY INSTRUCTIONS
1 - INTRODUCTION
This video intercom system pairs two modules:
a receiver-monitor and an easy-to-install and
use intercom panel.
Key features:
• Colour video reception: when a visitor
touches the intercom panel call button, the
panel immediately transmits the image to
the screen and a chime indicates the visitor’s
presence.
• Short-circuit protection
• Reverse polarity protection
• Automatic exposure correction: the video
camera automatically adjusts its exposure to
match the ambient light conditions.
• The LEDs integrated in the intercom panel
allow visitors to be identied without the
need for additional lighting.
• Opening the door and a control system: by
pressing buttons on the monitor, you can
control an electric lock and a dry contact for
an automatic control system (not included).
• Opening of the gate or the electric strike plate
depends on the time it takes to read the RFID
badge.
IMPORTANT: This notice should be read
carefully prior to installation. In the case of any
problems, our Hotline technicians are at your
service to provide you with any information you
may need.
WARNING: any connection error may cause
damage to the device and void the warranty.
2 - MAINTENANCE AND CLEANING
Before installing your intercom, it is important
to check the following points:
• Do not install in cases of extreme humidity,
temperatures, corrosion risk or dust.
• Do not expose to direct sunlight, rain, or high
humidity.
• Do not plug the device into a multi-socket
plug adaptor or extension cord.
• Be careful not to lose the administrator
badge (red colour) or your product will be
locked and the warranty voided.
Keep it in a safe place.
• Do not install near other electronic devices
such as computers, televisions or video
recorders.
• Do not install near acidic chemicals, ammonia
or sources of toxic gases.
• Do not clean with abrasive or corrosive
products. Use a damp cloth with soapy
water.
• Unplug the device if it is not being used for an
extended period of time.
• Do not plug the device into national
telecommunications installations.
• The cable between the monitor and intercom
panel must not be extended. Avoid junctions
(insulating screw joints, soldered joints, etc.)
3 - RECYCLING
This logo indicates that devices
which are no longer in use
must not be disposed of as
household waste. They are
likely to contain hazardous
substances that are
dangerous to both health and the
environment. Return the equipment to your
local distributor or use the recycling
collection service provided by your local
council.
Pour en savoir plus :
www.quefairedemesdechets.fr
VIDEOPHONE SMART CONNECT
EN 8
www.mythomson.com
GND
B - PRODUCT DESCRIPTION
1 - CONTENTS OF THE KIT
2 - GENERAL INFORMATION
This videophone is composed of an interior response station with touch-sensitive buttons and an exterior
panel with an intercom and camera, allowing the person inside to see and communicate with the visitor
outside who rings the doorbell. It is easy to install as only two wires are needed for all functions: bell, video
image, intercom and strike plate and automatic opener controls. For effective usage, please carefully
read this instruction manual.
3 - MONITOR
4Plug-in power supply
5 5 RFID badges: 2 users (grey), 1 admin
(yellow), 1 badge - (red), 1 badge + (blue)
1 7"monitor
2“Smart” wall bracket
3 Intercom panel and protective shield
1x 1 5x 5
3x 1
2x 1 4x 1
1
6 9
4
8 11
12
5
2
3
GND
GND
GND
7 10
5Connector
6Red: Connecting to power supply
7Green: Connecting to intercom panel
8Blue: Connecting to additional monitor
17" LCD screen
2Touch-sensitive buttons
3Microphone
4Loudspeaker
9EN
EN
www.mythomson.com
VIDEOPHONE SMART CONNECT
B - PRODUCT DESCRIPTION
9Indicator light for connecting an additional
monitor :
Red = Connection error
Blue = Connection OK or monitor not present
10 Power supply indicator light :
Red = Connection error
Blue = Power supply connected correctly
11 Intercom panel connection indicator light :
Red = Reverse polarity
Blue = Wiring OK
12 Intercom panel connection indicator light
: Red = intercom panel
not connected (wire unplugged or cut)*
Blue = connection OK
* This is completely normal if the monitor is
used as an additional monitor on an existing
installation and no intercom panel is directly
connected to it
4 - INTERCOM PANEL
1
3 4
8
5
6
7
GND
GND
9
10
1Twilight sensor
2White LEDs (night vision)
3Camera lens
4Microphone
5Loudspeaker
6Backlit call button and RFID badge scan area
7Tamper-resistant retaining screw
8Connecting of the monitor
9Connecting of the electric strike plate
10 Connecting of the dry contact (gate
automation )
11 Loudspeaker volume setting (located under
the rubber button)
12 RFID reset button (under the rubber plug)
5 - WALL BRACKET
Themonitorisdesignedtobexedtothewall.Awallbracketandthenecessaryfastenersareincluded.
6 - MAINS ADAPTER
A 230 Vac 50 Hz/15 Vdc 1A mains adapter for powering the monitor is included in the kit. Do not use other
power supplies as they could cause irreparable damage to the device and invalidate the warranty. Do not
cut or extend the wire of the mains adapter or the warranty will be void. The 15V wire of the adapter is
indicated by the presence of a red + 15V label. The ground wire of the adapter is indicated by the presence
of a black ENL label.
Notes:
• When the call button is pressed,
the monitor rings inside and the
video switches on.
• To change the name plate label,
remove the plastic protective
cover on the front by sliding a small
at screwdriver into the notch
provided for this purpose.
bob marley operat
11
2
12
VIDEOPHONE SMART CONNECT
EN 10
www.mythomson.com
C - INSTALLATION
Important notes and advice:
• In order to make the most of your intercom
panel,weadviseyoutocongureit(loudspeaker
volume)beforeitisinstalledinitsnallocation.
To do this, you will need to connect it on a table,
toensure that the settings have beencongured
correctly.
• If you test your product before installing it, please
do not do this with the intercom panel
and the monitor in the same room, to avoid the
emission of a high-pitched sound (Larsen effect).
• Do not expose the camera directly to the sun or
facingareectivesurface.
• Tip: it is recommended for the wires to be
covered by a sheath to protect them from bumps
and the weather.
1 - WIRING
To avoid the risks of interference and malfunction,
do not pass the wire for your videophone through
the same sheath as that housing the electrical
wires (230V - 50Hz). Each cable connecting the
monitor and the intercom panel must be a single
part. Avoid joints (insulating screw joints, soldered
joints, etc.)
Note: Do not under any circumstances double
wires to increase the wire size.
1.1. Connecting the videophone (screen,
intercom panel and camera, see g. 1, g. 2)
• Ensure proper connection of the wires,
following one of the wiring diagrams depending
onthedesiredconguration.
• Take careful note of the label afxed to the
front of the smart device and at the back of the
intercom panel.
• Depending on the selected conguration,
congureyourmonitorasa“Master”or“Slave”.
You can adjust this setting through the settings
management menu of your monitor.
1.2. Wiring gate automation
• The intercom panel provides a dry-contact
connection, without an electric current, to
be connected to the control button for your
automated gate.
•Connectitdirectlytotheterminalsidentiedon
the description of the intercom panel (Section 4
- Intercom panel) at the back of the board (no
polarity to follow).
• The opening function can only be used if the
respective intercom panel video is displayed.
1.3. Connecting an electric strike plate or
lock
Important: The electric strike plate or lock that
you install must be equipped with a mechanical
memory. The power supply to the lock must not
exceed 12V/1.1A.
•Connectitdirectlytotheterminalsidentiedon
the description of the intercom panel (Section 4
- Intercom panel) at the back of the board (no
polarity to follow).
• The opening function from the monitor can
only be used if the respective intercom panel
video is displayed.
2 - CONFIGURATION OF THE INTERCOM PANEL (SEE
FIG. 1, FIG. 2)
2.1. Intercom volume setting
Setting the volume of the intercom and
conversation volume can be done from the
settings interface on the video intercom screen.
More details are available in Section D - Use.
2.2. Conguration of the RFID function
The RFID function enables opening to be
managed using badges from the intercom
panel, even when the screen is switched off.
2.2.1. Programming (or resetting) the
administrator badges
Whenswitchingonthedeviceforthersttime,
thebadgesmustbeconguredinthefollowing
order:
1. Press the reset button at the back of the
intercom panel for 5 seconds, the intercom
panel emits 6 short beeps.
2. Swipe the administrator badge (yellow),
a short beep conrms that it has been
programmed.
3. Swipe the + badge (blue), a short beep
conrmsthatithasbeenprogrammed.
Indice
Altri manuali THOMSON Sistema di interfono
THOMSON
THOMSON 513133 Manuale utente
THOMSON
THOMSON 513128 Manuale utente
THOMSON
THOMSON IZZY-768W2 Manuale utente
THOMSON
THOMSON 513127 Manuale utente
THOMSON
THOMSON 513125 Manuale utente
THOMSON
THOMSON SMART 761 Manuale utente
THOMSON
THOMSON Smart Bracket II Manuale utente
THOMSON
THOMSON 512166 Manuale utente
THOMSON
THOMSON 513133 Manuale utente
THOMSON
THOMSON 513127 Manuale utente
