Tiger PRESSURE TREATED OCTAGONAL Guida alla configurazione

TIGER

PRESSURE

TREATED

OCTAGONAL

GENERAL ASSEMBLY

INSTRUCTIONS

TIG/INS59

BEFORE YOU GET STARTED

PLEASE READ INSTRUCTIONS CAREFULLY

• Check the pack and make sure you have all the parts listed.

• When you are ready to start, make sure you have the right tools at hand (not supplied).

• Ensure there is plenty of space and a clean dry area for assembly.

TIMBER

As with all natural materials, mber can be aected during various weather condions. For the duraon of

heavy or extended periods of rain, swelling of the wooden panels may occur. Warping of the wood may also

occur during excessive dry spells due to an interior moisture loss. Unfortunately, these processes cannot be

avoided but can be migated. It is suggested that the outdoor building is sprayed with water during extended

periods of warm sunshine and sheltered as much as possible during rain or snow.

To validate your guarantee and ensure longevity of the product, it is ESSENTIAL that your building is treated

with an appropriate high-quality oil or solvent based preservave AFTER assembly, both internally and

externally, and annually thereaer. All glazing units must be sealed (internally and externally) with silicone or

other waterght sealant.

BUILDING A BASE

Care must be taken to ensure the product is placed on a suitable base. When thinking about where the building

and base is going to be constructed, ensure that there will be access to all sides for maintenance work and

annual treatment.

Ensure the base is rm and level and is built on rm ground, to prevent distoron.

The constructed base must be at least the size of product as referenced in supplied construct diagram. It is also

recommended that the oor be at least 25mm above the surrounding ground level to avoid ooding.

TYPES OF BASE

• Durable plasc grid*.

• Concrete 75mm laid on top of 75mm hard-core.

• Slabs laid on 50mm of sharp sand.

• Timber Base - Self constructed/Buy pre-made.

*We recommend a Fastt EcoBase for your building. It is durable, lightweight, exible and easy to put in place.

Please see gersheds.com for details.

WOOD WARPING

MAY OCCUR

WINTER

EXPANSION

SUMMER

CONTRACTION

PLASTIC BASE SLAB BASE TIMBER BASE BROKEN SLABS BARE SOIL LOOSE GRAVEL

02 gersheds.com 0113 205 4189 sales@gersheds.com

CONCRETE BASE

Please retain instrucons for future reference

CAUTION:

All buildings should be erected

by two competent adults.

CAUTION:

It is advisable to wear gloves

during building installaon.

Whilst all products manufactured are made to the highest standards of safety, we cannot accept responsibility for your safety whilst erecng or

using this product.

Pressure Treated Buildings & Treatment:

Our Pressure Treated (or tanalised) Range of buildings are impregnated with Tanalith-E - the latest generaon wood

preservave. This has a pale green nt to the mber as the treatment is a copper-based product designed to limit the

chance of rot and insect aack. Once erected, your building should be treated annually, both internally and externally with

an appropriate high-quality oil or solvent based preservave.

MADE IN THE UK SINCE 1913.

We have been making our high quality,

great value garden buildings here in

Britain for decades.

BEFORE YOU GET STARTED - PRE ASSEMBLY

TOOLS REQUIRED:

We recommend using the following tools (not supplied):

FIXING KIT GUIDES:

CN13

FX06 - NAIL KITS HEAVY DUTY

For Heavy Duty Shed Products:

Clout Nails (13mm Galvanised - QTY 450)

PP25

Panel Pins (25mm - QTY 200)

N40

Nail (40mm Galvanised - QTY 85)

N65

Nail (65mm Bright - QTY 20)

N100

Nail (100mm Bright - QTY 100)

CB100

Coach Bolts (100mm - QTY 8)

BUILDING PACK CONTENTS:

For full details of what should be included please see the itemised packing list that is supplied with the delivery.

They are also available on request in pdf form from our helpful Customer Support team – please call:

0113 205 4189 or use the “Items Delivered Query” form at gersheds.com/contact.

04 gersheds.com 0113 205 4189 sales@gersheds.com

SCREWDRIVER +

RUBBER MALLET DRILL LADDER TAPE MEASURE SHARP KNIFE SPIRIT LEVELHAMMER

WOOD SAW SPANNER

Please retain instrucons for future reference

• Assembly is straighorward if you follow these step-by-step instrucons.

• We recommend geng everything aligned properly before screwing together and that

screw holes should be pre-drilled to avoid spling the mber. (Do not come pre-drilled).

IMPORTANT

• Before assembly, please make sure you have a suitable base ready to erect your building on.

• Your base MUST be rm and level to ensure that the building is assembled properly and is square.

• DO NOT start your build unl you have checked that all the parts of your building are present, correct and in a

suitable condion.

• Panels may have become twisted during loading/unloading and/or transportaon. Please check that all framing and cladding

are square before beginning assembly.

• If you are organising a third party to install your building, it is best pracce not to schedule this immediately on receipt of your

order, to give you me to check your delivery

Step 1:

LAYING THE FLOOR

• SINGLE FLOOR - Lay oor down in the desired posion. (Detail A)

TIGER PRESSURE TREATED OCTAGONAL - GENERAL ASSEMBLY INSTRUCTIONS

06 gersheds.com 0113 205 4189 sales@gersheds.com

Step 2a:

INSTALLING SIDE AND GABLE PANELS

• Posion blank panel along back edge of oor. Oer up panels either side. (Detail B1)

NOTE: CHECK THAT ALL PANELS ARE AT RIGHT ANGLES TO EACH OTHER AND THE FLOOR.

• Secure together with 4x N100 evenly spaced. (Detail B2)

• Repeat process for remaining panels.

• When ng the door panel. you will

nd it easier to open the doors before

securing together.

DO NOT FIX TO FLOOR.

N100

Please retain instrucons for future reference

Step 3:

SECURING SIDE AND GABLE PANELS

• Check panels are square by measuring between points shown. (Detail C1)

• If measurements are equal, your panels are square. If not, manually adjust to suit.

NOTE: DO NOT TRIM.

• Secure panels to the oor using 2x N100 per panel. Ensure the N100 are driven through the panels and into

the oor bearers. (Detail C2)

NOTE: PANELS HAVE BEEN REMOVED FOR CLARITY.

NOTE: CHECK THAT ALL PANELS ARE AT RIGHT ANGLES TO EACH OTHER AND THE FLOOR.

N100

1 2

TIGER PRESSURE TREATED OCTAGONAL - GENERAL ASSEMBLY INSTRUCTIONS

08 gersheds.com 0113 205 4189 sales@gersheds.com

Step 4:

FIX CORNER STRIPS

• Secure the moulded corner strips at each corner of the shed with 8x N40 per corner strip.

NOTE: THESE CORNER STRIPS MAY NEED CUTTING TO SIZE

Please retain instrucons for future reference

Step 5:

INSTALL FIBREGLASS ROOF

• Place breglass roof in posion on top of walls.

• Screw 1x CB100 into top rail of each wall panel to secure breglass roof. (Detail D)

• Secure acorns to top of breglass roof from inside using screws provided.

• 8x6 MODELS HAVE 2x ACORNS.

• 6X6 MODELS HAVE 1x ACORN.

FIBREGLASS

ROOF

WALL PANEL

CB100

TIGER PRESSURE TREATED OCTAGONAL - GENERAL ASSEMBLY INSTRUCTIONS

10 gersheds.com 0113 205 4189 sales@gersheds.com

Step 6:

INSTALLING GLAZING

• Glaze windows by securing glass/styrene with PP25 supplied, from the inside. (Detail E)

NOTE: ALL WINDOWS MUST BE SEALED INSIDE AND OUT WITH SILICONE, PUTTY, OR ANY OTHER

WATER-TIGHT SOLUTION. (NOT SUPPLIED).

NOTE: PLEASE DO NOT CONFUSE YOUR CORNER STRIPS WITH WINDOW BEADING.

WE DO NOT SUPPLY WINDOW BEADING AS STANDARD WITH OUR BUILDINGS UNLESS ORDERED.

• Contact our friendly customer support team to order a standard window glazing kit, complete with beading

and sealant.

PP25

Indice

Altri manuali Tiger Casa da giardino

Tiger

Tiger Delta Manuale utente

Tiger

Tiger Lana Manuale utente

Tiger

Tiger TIGERFLEX TIG/INS39 Manuale utente

Tiger

Tiger Tigercub Magic Mansion Manuale utente

Tiger

Tiger OPTIMA Manuale utente

Tiger

Tiger BLAKE Manuale utente

Tiger

Tiger SAMPI Manuale utente

Tiger

Tiger RAYNER Manuale utente

Tiger

Tiger KERR Manuale utente

Tiger

Tiger MAYFLOWER SUMMERHOUSE Manuale utente

Tiger

Tiger SHERE TIG/INS16 Manuale utente

Tiger

Tiger CORBETTI Manuale utente

Tiger

Tiger TIGERFLEX MODA Manuale utente

Tiger

Tiger PETHOUSE & RUN Manuale utente

Tiger

Tiger Tigercub Groovy Garage Manuale utente

Tiger

Tiger Tigercub Crazy Cottage Manuale utente

Tiger

Tiger SHIPLAP APEX WINDOWLESS SHED Manuale utente

Tiger

Tiger PANTHERA Manuale utente

Tiger

Tiger ROSEN Manuale utente

Tiger

Tiger Caspian Manuale utente

Tiger

Tiger MALAYAN Manuale utente

Tiger

Tiger SIGMA TIG/INS48 Manuale utente

Tiger

Tiger Aura Manuale utente

Tiger

Tiger TIGERFLEX ZORA Manuale utente

Manuali Casa da giardino popolari di altre marche

Mercia Garden Products

Mercia Garden Products 0628LOG181-V4 Manuale utente

Lemeks

Lemeks Palmako PA120-5930-6 Manuale dell'installatore

Gartenhaus-King

Gartenhaus-King Valery Manuale utente

Rion

Rion Hobby Gardener Manuale utente

POD

POD Camping 480 Manuale utente

Select

Select ISAAC E9682 Manuale utente

Mercia Garden Products

Mercia Garden Products 01DTSHPWOR1010DDOW-V4 Manuale di istruzioni

Palmako

Palmako Saale Manuale utente

Lemeks

Lemeks Palmako Kira EL16-3623 Manuale dell'installatore

Mercia Garden Products

Mercia Garden Products 0644LOG186-V4 Manuale di istruzioni

Palmako

Palmako Roger FR44-5953-2 Manuale utente

Mercia Garden Products

Mercia Garden Products 03DTSHHP1206HGD4MW-V1 Manuale di istruzioni

WAR-LOCK

WAR-LOCK GARDENSHED Skillion Series Manuale utente

Pergola kits USA

Pergola kits USA PREMIUM VINYL PAVILION Manuale utente

G21

G21 Boston 882 Manuale utente

Lemeks

Lemeks Palmako Grace PM56-4529 Manuale dell'installatore

Mercia Garden Products

Mercia Garden Products 03WES0808-V1 Manuale di istruzioni

Shire

Shire Salcey Manuale utente