Timeguard TRT039N Manuale
Installation & Operating Instructions
7 Day Digital Programmer
4 Channel – Surface Mount
Model: TRT039N
1
1. General Information
These instructions should be read carefully and retained for further reference
and maintenance.
2. Safety
• Before installation or maintenance, ensure the mains supply to the
programmer is switched off and the circuit supply fuses are removed
or the circuit breaker turned off.
• It is recommended that a qualified electrician is consulted or used for the
installation of this programmer and install in accordance with the current
IEE wiring and Building Regulations.
• Check that the total load on the circuit including when this programmer is
fitted does not exceed the rating of the circuit cable, fuse or circuit breaker.
• To clean use a clean dry cloth only. Do not use any liquid cleaners.
3. Technical Specifications
• 230V AC 50 Hz
• This thermostat is of Class ll Construction and must not be earthed
• Switch Rating: 3(1)A
•Switch Type: Single pole, double throw (SPDT)
for heating zones and hot water,
voltage free contacts
•Connection Type: 3 wire
•Installation Type: Surface mount with wall plate
• Micro Disconnection: Type 1.B control action
•Operating Temperature Range: 0°C to +40°C
• Time Control Periods: 3 per day
• Clock Format: 12hr AM/PM or 24hr
• Summer/Winter Changeover: Day light saving, GMT or BST
• Holiday Mode: 0 to 31 day programme suspension
• Boost Function: 1 or 2 hour for heating zones
and hot water
2
• Battery Backup: 7 day, factory fitted rechargeable
(non-replaceable)
• Illumination: Blue LED illuminated on setting for button
surrounds and display
• CE Compliant
• Dimensions (H x W x D): 90 x 135 x 30mm
TRT039N Front View
Output LED’s for channel
switch status
12hr am/pm
or 24hr clock
timer display
(illuminated
on setting)
1 and 2 hour boost for central
heating zones and hot water
(illuminates on setting)
Advance button
to next programme
Programme override
for each channel
Flip down cover conceals
setting buttons
3
4. Siting
• The TRT039N should be located at a position which eases wiring runs
and gives good access for programming.
• It should be mounted approximately 1.5m above floor level.
5. Installation
5.1 Ensure the mains supply is switched off and the circuit supply fuses
are removed or the circuit breaker turned off.
5.2 Remove the wall plate from the unit, by undoing the retaining screws,
and pivoting the bottom of the unit outwards. The TRT039N body can
then be lifted off.
5.3 Mark the position of the mounting holes on the wall using the wall plate
as a template. Drill out the mounting holes taking care to avoid any
joists, electrical cables or water/gas pipes that may be hidden beneath
the surface. Insert the rawl plugs into the holes.
5.4 Pass the 230V 50Hz mains supply and load cables through the opening
of the wall plate. Allow sufficient excess cable to wire up the unit, but
not too much to make it difficult to close the unit to the wall plate.
5.5 Fix the wall plate to the wall using the correct mounting screws for the
rawl plugs installed. The retaining screws which secure the unit to the
wall plate should be at the bottom.
5.6 Terminate the cables into the terminal block ensuring correct polarity
is observed and that all bare conductors are sleeved (See section 6.
Connection Diagram). Make sure that the curved washer grips
the conductor.
5.7 To reinstall the unit onto the wall plate, first ensure the wall plate
retaining screws are loosened enough to clear the TRT039N body, then
engage the top of the TRT039N onto the wall plate retaining tabs, and
push firmly downwards and then upwards. There will be some resistance
from the terminals.
5.8 Once in place, secure with the retaining screws making sure not to
over tighten.
4
TRT039N Wall Plate
Alternate mounting holes
Wall plate retaining screws
Retaining tabs
Mounting
holes
COMONONCOMONNL
N P1 P2 P3 P4 P5L
230V 50Hz
Mains
Supply
Neutral
(Blue or
Black)
P3 ON =
Normally
Open
Contact
–
Switch
Live for
Heating
Zone 2
P1 ON =
Normally
Open
Contact
–
Switch
Live for
Heating
Zone 1
P2 COM =
Voltage
Free
Common
P4 ON =
Normally
Open
Contact
–
Switch
Live for
Hot
Water
P5 COM =
Voltage
Free
Common
ON
P6
P6 ON =
Normally
Open
Contact
–
Switch
Live for
Hot
Water
230V 50Hz
Mains
Supply
Live
(Brown
or Red)
5
6. Connection Diagram
Connect the 230V 50Hz mains supply and load cables to the terminal block
which are marked as follows;
• Note: Check boiler instructions before connecting.
6
7. Reset from Power-up
7.1 Restore mains to the unit after making sure to check all system wiring
is complete.
7.2 Press the reset button located beneath the flip down cover on the
front of the unit, the screen will fade and then reappear showing all
available channels as well as the default time and date at the bottom
of the display.
7.3 There are 3 time controlled periods per day, and the default programmes
are as follows;
8. Setting the Time and Date
8.1 To set up the time and date, press the menu button. Then navigate
to the settings option using the advance buttons marked beside the
+ and – indicators. Press enter to select settings.
8.2 On the settings menu, the time and date option will be highlighted.
Press enter to begin setting the time and date.
7
8.3 The hour will be highlighted on the display.
Use the advance buttons marked beside the
+ and – indicators to alter the hour.
Press enter once to confirm.
8.4 The minutes will now be highlighted on
the display. Use the advance buttons
marked bedside the + and – indicators to
alter the minutes.
Press enter once to confirm.
8.5 The day of the month will now be highlighted
on the display. Use the advance buttons
marked bedside the + and – indicators
to alter the day of the month.
Press enter once to confirm.
8.6 The month will now be highlighted on
the display. Use the advance buttons
marked beside the + and – indicators
to alter the month.
Press enter once to confirm.
8.7 The year will now be highlighted on the display. Use the advance buttons
marked beside the + and – indicators to alter the year. Press enter once
to confirm.
8.8 Press the menu button twice to exit to the settings menu.
8
Daylight Saving
8.9 Automatic summer/winter times (BST+1/BST) can be selected
or deselected. It is on by default.
8.10 Select the daylight savings option from the settings menu.
Set this value either ON or OFF using the advance buttons marked beside
the + and – indicators. When complete press the menu button to exit
to the settings menu.
Clock Options
8.11 12 hour or 24 hour clock formats can be selected. The default value is
the 24 hour format.
8.12 Select clock options from the settings menu. Set this value to either
24 hour or AM/PM using the advance buttons marked beside the
+ and – indicators. When complete, press the menu button to exit
to the settings menu.
9
9. Programme Preparation (Headings)
9.1 Decide which heading suits best for the channels to be displayed. They
can be set as channels being channel 1, 2, 3 and 4, split as heating and
hot water being heating 1, heating 2, heating 3 and water as the fourth
channel as well as having an option for heating on the first 2 channels
(1 & 2) and water on the last two channels (3 & 4). Zones can be applied
to each channel as a heading being zones 1, 2, 3 and 4.
9.2 To implement this setting, press the menu button and select the settings
menu using the advance buttons marked beside the + and – indicators.
Press enter to confirm.
9.3 Once in the settings menu, select the headings option using the advance
buttons marked beside the + and – indicators and press enter.
9.4 Select the heading required using the advance buttons marked beside
the + and – indicators and press enter to confirm.
9.5 Once the heading is set, press the menu button until the main screen has
been reached.
Indice
Altri manuali Timeguard Controllori
Timeguard
Timeguard SureTime STLW1000 Manuale
Timeguard
Timeguard SLB2300RF Manuale
Timeguard
Timeguard PDSM1500 Manuale
Timeguard
Timeguard SLFM360 Manuale
Timeguard
Timeguard RTS113 Manuale di programmazione
Timeguard
Timeguard TRTD7N Manuale
Timeguard
Timeguard E269H-Synchronous Manuale
Timeguard
Timeguard SLFM360L Manuale
Timeguard
Timeguard PDFM1500 Manuale
Timeguard
Timeguard PDFMMINIL Manuale
Timeguard
Timeguard TS900N Istruzioni per l'installazione
Timeguard
Timeguard ELU56 Manuale
Timeguard
Timeguard MLSA360N Manuale
Timeguard
Timeguard RTS113Q Manuale di programmazione
Timeguard
Timeguard SLB2300RF Manuale
Timeguard
Timeguard PDRS1500N Istruzioni per l'installazione
Timeguard
Timeguard SLW360N Manuale
Timeguard
Timeguard NSLDD1000 Manuale
Timeguard
Timeguard TLRX05 Manuale
Timeguard
Timeguard SLW360L Manuale
