Timeguard TLRXC1 Manuale utente

INSTALLATION & OPERATING

INSTRUCTIONS

CHIME

RECEIVER

Cat No. TLRXC1

iTLRXC1_Instructions.qxd 1/19/05 11:55 AM Page 1

Introduction

The TLRXC1 Chime Receiver is part of the Timeguard

range of PIR products which communicate by radio

frequency (r.f.) signals.

This enables substantial amounts of wiring to be

eliminated which is particularly useful in long runs

and coverage of outbuildings.

It is a plug in adapter which receives r.f. signals from

transmitters (denoted by Tx in the range) that it has

been programmed to recognise and produces an

audible warning as well as turning on lights connected

to its socket outlet.

In the following instructions products with catalogue

numbers including TX (ones that send information

about PIR detection) are referred to as Tx units and

products with catalogue numbers including RX (ones

that receive information about PIR detection) are

referred to as Rx units.

Tone/Volume Manual

Override

LED

Time On

“PROG”

Program/Reset

iTLRXC1_Instructions.qxd 1/19/05 11:55 AM Page 2

Parts included

• Chime Receiver unit.

• Instruction manual. Please keep safe for future

reference.

Selecting a location

1. Position your Transmitter in desired area, if using a

PIR perform walk tests to confirm detection zones.

2. Position TLRXC1 in a desired area up to 100m away

from the Tx, take into account the path between the

sensor to ensure range is acceptable.

The Chime Rx can be placed in any socket outlet

within the home, it can be used purely as a sounder,

reacting to any transmission signals it receives from

any Tx or it can be used to switch an internal lamp

on/off as desired. We suggest that firstly, the

Floodlight Tx is placed in its optimum position to give

the coverage and detection required, then the Chime

Rx is fitted to a socket outlet at a point where it can

receive the Tx`s signal. (This will be less than 100m

away if walls or chain link fences come between the Tx

and Rx units - if there is any doubt about whether

communication will take place make temporary

installations before programming).

iTLRXC1_Instructions.qxd 1/19/05 11:55 AM Page 3

Installation

1. If you require an internal lamp to be switched by the

Floodlight Tx, plug a lamp (500W max incandescent or

halogen) into the unit’s socket outlet. (The TLRXC1 is

not suitable for switching fluorescent, low energy or

discharge lamps).

Ensure the lamp is switched on when operation is

required.

2. Plug the Chime Rx into the wall outlet. The chime

will then scroll through 6 audible sounds to inform the

user of its sound options. There will then be four

“beeps” and the flashing LED indicates that the Rx is

ready for programming.

Note:- This will only happen the first time the Chime

Rx is plugged into the outlet.

Programming

PLEASE REFER TO THE INDIVIDUAL

INSTRUCTION MANUALS OF THE Tx UNITS TO BE

USED WITH THE TLRXC1.

Each Rx unit needs to learn the codes included in the

messages from all the Tx units which are required to

control it (up to 17).

iTLRXC1_Instructions.qxd 1/19/05 11:55 AM Page 4

Turn OFF/remove batteries from any Tx unit which is

not required to control this Rx unit. Turn off any other

Rx units.

If it is convenient more than one Rx unit can learn the

code of a Tx unit simultaneously in which case leave

these Rx units switched on.*

The TLRXC1 unit needs to be set in Program Mode. Plug

it in to a live socket (the first time this is done the unit

will go through its 6 choices of audible warning). Plug a

lamp into the unit’s socket and turn the lamp switch on.

The LED on the unit will flash slowly for 5 minutes

indicating it is in Program Mode.

Go to the Tx** unit to be introduced to the TLRXC1 and

move across the face of its PIR lens within detection

range to cause it to detect (indicated by the lights under

control turning on for most Tx units and by a flash

from the red LED on the TLTXDCB).

The TLRXC1 will respond with a “beep” and the lamp

plugged into it will turn on (indicating correct code

learning).

* Any other Rx units left connected should now be

checked in the same way.

If an additional Tx unit is required to be introduced

press the PROGRAM/RESET button for 1 to 2 seconds***

a single “beep” will sound and the LED will stop

flashing and stay on indicating exit from Program Mode.

Press this button again and the LED will start to flash

again indicating a new 5 minute period of Program Mode.

*Any other Rx units required to learn the code of this

new Tx unit should be left connected.

** If introducing the TLTXK2 hand held transmitter press

the “1” button on this unit to activate the TLRXC1.

***If the button is pressed for 5 seconds or more then all

the codes that have been learnt will be erased.

iTLRXC1_Instructions.qxd 1/19/05 11:55 AM Page 5

Selecting the alarm/lamp

function

1. Press the PROGRAM/RESET button for 1 to 2

seconds. (A “beep” will sound and the LED will flash

indicating the unit is in Program Mode).

2. Make a TX unit which has been introduced detect.

Press the TONE/VOLUME button to select the

preferred sound (each will play twice, choose the first

if you want the lamp to turn on, the second if you want

the lamp to remain off).

3. Press the PROGRAM/RESET button. A “beep” will

sound and the LED will stop flashing and remain on

indicating exit from Program Mode.

Selecting the lamp on time

To set how long the lamp will remain on after the

TLRXC1 has received a signal from a Tx unit, set the

ON TIME dial anywhere from 5 seconds (“minus”

setting) to 15 minutes (“plus” setting).

Selecting the volume

To set the volume for the chime tone, make a Tx unit

which has been introduced detect and the Rx unit will

play the tone you have chosen. Press the TONE/

VOLUME button to select the volume you require

high, low or “beep”.

You cannot change the volume whilst the TLRXC1 is in

Program Mode.

iTLRXC1_Instructions.qxd 1/19/05 11:55 AM Page 6

Erasing all codes

Tx unit codes can be erased for reprogramming.

To erase codes, while the TLRXC1 is powered, press

and hold the PROGRAM/RESET button for more than

5 seconds. All programmed codes will be erased and

4 "beeps" will sound. This will clear the unit of all

programmed codes and place it into the Program

Mode.

Manual override

The Lamp can be switched ON/OFF independently

of any transmission signal by using the MANUAL

button.

Press this button and the lamp will turn ON. The LED

will flash indicating it is in Manual Mode. To return to

Auto Mode, press the button again and the light will

turn off. The LED will light permanently to indicate the

product is in Auto Mode.

Note:- If the Floodlight Transmitter detects movement

when the Chime Rx is in Manual Mode, it will send a

signal to the Chime Rx which will play its

programmed sound and the connected light will

“blink” off and on once quickly.

iTLRXC1_Instructions.qxd 1/19/05 11:55 AM Page 7

Solution

1. The lamp switch is

turned off.

2. Check Light bulb.

3. Tx unit photocell

determines it is daylight,

adjust Tx units DUSK/

DAWN control for daylight

operation.

4. Tx unit is too far from Rx

unit, move closer.

1. Sticker over photocell

window has not been

removed from Tx unit.

2. Sensor is installed in a

dark location, adjust

DUSK/DAWN control.

3. The TLRXC1 is set in

Manual mode. Press the

MANUAL button once to

return to Auto Mode.

1. Tx unit may be sensing

small animals or passing

cars. Adjust horizontal

position or mask lens.

2. Reduce range by pointing

the Tx unit detector down

more.

1. Tx unit is too far from

TLRXC1. Move closer.

This is the Low battery

signal. replace batteries in

the Tx unit.

Problem

• Chime/Lamp will not turn

on when motion is sensed.

• Chime/Lamp comes on in

Daylight

• Chime/light comes on for

no apparent reason

• Light comes on irregularly

when motion is sensed.

• Battery operated Tx unit

LED flashes off and on

twice when activated

Troubleshooting guide

iTLRXC1_Instructions.qxd 1/19/05 11:55 AM Page 8

Power Supply:

Maximum Switchable Load:

Time On Adjustment:

Transmission Range:

Conforms to Directives:

230 V AC ~ 50Hz

500W filament/incandescent

only (not suitable for

fluorescent, low energy or

discharge lighting)

5 seconds to 15 minutes

Up to 100m (varies with

surrounding structures)

73/23/EEC and 89/336/EEC

Technical specifications

iTLRXC1_Instructions.qxd 1/19/05 11:55 AM Page 9

HELPLINE

020-8450-0515

For a product brochure please contact:

Timeguard Ltd.

Victory Park, 400 Edgware Road,

London NW2 6ND

020-8452-1112

or email csc@timeguard.com

5 Year Guarantee

In the unlikely event of this product becoming faulty due to

defective material or manufacture within 5 years of the date

of purchase, please return it to your supplier in the first year

with proof of purchase and it will be replaced free of charge.

For years 2 to 5 or any difficulty in the first

year telephone the helpline on 020 8450 0515.

FIVE YEAR

GUARANTEE

iTLRXC1_Instructions.qxd 1/19/05 11:55 AM Page 10

Indice

Manuali Ricevitore popolari di altre marche

Garmin

Garmin GA 23 Manuale utente

Aiphone

Aiphone PS-12F Manuale utente

IMES

IMES TCS-01CA-PMI Manuale utente

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuale

AMIMON

AMIMON AMN12310 WHDI Manuale utente

Dual

Dual DMCPA79BT Istruzioni operative

Sound Associates

Sound Associates SA652P Manuale utente

Sherwood

Sherwood NewCastle R-772 Manuale utente

Audio

Audio A10-RX Series Manuale utente

AllSee

AllSee PushShare PSRV1.1 Manuale utente

DEMAG

DEMAG DRC-DR D2 Manuale utente

Teleco

Teleco TVRCL868A02 Manuale utente

Bosch

Bosch RF3222E Manuale utente

Kramer

Kramer 631R Manuale utente

Xpress

Xpress xmc10 Manuale utente

JVC

JVC KD-MR1BTS Manuale utente

Omega Engineering

Omega Engineering UWTC-REC3 Manuale utente

e-survey

e-survey E300 Pro Manuale utente