Titon TP325 Manuale utente
ventilation systems
First Fix Base
Product Manual
EN
TP325
2
Warnings, Safety information and
Guidance
Important Information
Important: read these instructions fully before the
installation of this appliance
1. Installation of the appliance and accessories must be carried
out by a qualied and suitable competent person and be car-
ried out in clean, dry conditions where dust and humidity are
at minimal levels.
2. All wiring must conform to current I.E.E. Wiring Regulations
and all applicable standards and Building Regulations.
3. The appliance must be connected to a local double pole
isolation switch with a contact separation of at least 3mm.
Ideally located adjacent to the unit.
4. The appliance must be earthed.
5. Seperate cables must be used for power and boost control.
6. Units are suitable for 230V ~ 50/60Hz single phase with a
fuse rating of 3A.
7. Q Plus models - Boost cable - Unshielded 4 Core 18-24AWG
Stranded, Tinned Copper.
8. Boost cables should not be placed within 50mm or on the
same metal cable tray as any 230V lighting or power cables.
9. The unit must be stored in a clean and dry environment.
10. Do not install the appliance in areas where the following may
be present or occur;
• Excessive oil or a grease laden atmosphere,
• Corrosive or ammable gases, liquids or vapours,
• Ambient temperatures above 40°C or below -5°C,
• Humidity levels above 90% or is a wet environment.
3
11. The appliance is not suitable for installation to the exterior of
the dwelling.
12. This appliance can be used by children aged from 8 years and
above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have
been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved.
13. Children should be supervised to ensure that they do not
play with the appliance.
14. Ensure that external grilles are located away from any ue
outlet, in accordance with relevant Building Regulations.
15. The unit must not be connected to a tumble dryer.
16. The unit must not be connected to a cooker hood.
17. Precautions must be taken to avoid the back-ow of gases
into the room from an open ue appliance.
18. Ensure all ducting,is free from debris and blockages before
switching on the unit.
4
Warnings, Safety information and Guidance
Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Product Overview
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Component Identication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Packaging Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Installation
Fixing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Ducting Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
How to Convert Port Cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Wiring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Cable Entry Position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
CME1 TP350 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
CME1 Q Plus TP301A/301HA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
CME2 &2.1 Q Plus TP303A/303HA TP 303A/303HA/TP313A/TP313HA. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
CME2 & 2.1 Q Plus LS TP305HA/TP313HALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
CME2.1 Q Plus TP313CH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Contents
5
Product Overview
This booklet is required for the rst part of a two stage installation of one of the
following Units:
CME1 TP350
CME1 Q Plus TP301A
CME1 Q Plus TP301HA
CME2 Q Plus TP303A
CME2 Q Plus TP303HA
CME2.1 Q Plus TP313A
CME2.1 Q Plus TP313HA
CME2 Q Plus LS TP305HA
CME2.1 Q Plus LS TP313HALS
CME2.1 Q Plus TP313CH
The installer must be aware which specic model has been specied before
commencing installation.
CME1 TP350
CME1 Q Plus TP301A/301HA
CME2 & 2.1 Q Plus TP 303A/303HA/TP313A/TP313HA
CME2 & 2.1 Q Plus LS TP305HA/TP313HALS
CME2.1 Q Plus TP313CH
have dierent wiring requirements.
Ensure the correct wiring diagram is used for the installation.
The unit may be damaged if wired incorrectly.
The installer of the second stage will receive further documentation to complete
the installation and commissioning.
6
Dimensions
This diagram details the overall size of the unit and the additional space required
around the unit to allow for commissioning and future servicing and maintenance.
450
421
355
390
252
550
450
590
Service Void
All dimensions in mm
7
Component Identication
Base
Cover / Scroll / Inlet Ring assembly
Supplied as second x.
8
Packaging Contents
Inspect the unit when taking delivery. Check the unit for damage and that all
accessories have been supplied. The box contains:
CME Base x 1.
Port covers x 3.
This Product manual x 1.
All shortages or damage must be immediately reported to the supplier.
9
Notes
10
Installation
Fixing
1. The unit must be securely xed to a
smooth at surface, any orientation
is possible.
2. Mark the four xing hole centres
using the Base as a template.
3. Drill holes for xings, use 4mm
Pan Head screws. Always use a
xing type and length suited to
the substrate type. The unit weighs
approximately 5kg.
4. Mount the Base, ensuring it is not
distorted by the xings or mounting surface.
5. Clip the Motor and Lid assembly to the Base, ensure that all 6 clips have
engaged.
Tighten screws by hand, DO NOT over tighten screws or use power tools.
260
260
EXTRACT
PORT
Indice
Altri manuali Titon Fan
Titon
Titon TP221T Manuale utente
Titon
Titon SF Xtra Vent Series Manuale utente
Titon
Titon CME3Q+ Manuale del proprietario
Titon
Titon CME2 Q Plus LS Manuale utente
Titon
Titon CME2Q+ Manuale del proprietario
Titon
Titon HRV10.25 Q Plus ECO Manuale utente
Titon
Titon TIFC100HT Manuale utente
Titon
Titon CME1 Q Plus Manuale utente
Titon
Titon TP 342A Manuale utente
Titon
Titon HRV20 Q Plus ECO Manuale utente
Titon
Titon HRV2.75 Q Plus Manuale utente
Titon
Titon CME1 Manuale utente
Titon
Titon CME2.1 Q Plus TP312CH Manuale utente
Titon
Titon HRV10 Q Plus Manuale utente
Titon
Titon PIV L3 Manuale utente
Titon
Titon HRV1.25 QPtus ECO Manuale utente
Titon
Titon TP440MB Manuale utente
Titon
Titon HRV1.25 Q Plus ECO Istruzioni per l'installazione
Titon
Titon solitude Manuale utente
Titon
Titon MVHR Manuale utente
