Toa CI-600 Manuale utente

INSTALLATION MANUAL

COMPUTER INTERFACE CI-600

To obtain optimum results from this computer interface, please follow instructions in this manual

carefully. We suggest that you keep this manual handy for future reference.

CONTENTS

GENERAL DESCRIPTION...................................................... 1

PART

NAMES.......................................................................

INSTALLATION..................................................................... 2

CONNECTION

Input control connector and DC power supply ........... 3

Speech IN/OUT terminals.......................................... 3

RS-232C

connection..................................................

BACK-UP BATTERY.............................................................. 5

INITIAL

SET-UP

CI-600

...................................................

SPECIFICATIONS................................................................. 7

ACCESSORIES..................................................................... 7

GENERAL DESCRIPTION

The Toa CI-600 Computer Interface is used in conjunction with the SI-62 Speech Interface

and the EX-610, EX-620 or EX-630 exchange. Connected to a personal computer or data

terminal, the CI-600 permits system programming, personal information display, release

of fixed messages, etc.

PART NAMES

[Front-mounted facilities)

Knob

CI-600 without cover

* Each DIP switch is OFF when put downward and ON when put upward, with the switch

numbers 1 through 8 allocated left to right.

[Rear-mounted facilities)

RS-232C connecto r Input control connector Power input terminal

(CN1, CN2)

Speech IN/OUT terminal

SI-62

Ni-Cd battery

BAUD RATE DIP switch

Cover

Timer indicator MODE SELECT DIP switch *

1.Rack mounting (exchange is mounted in an equipment rack.)

Attach the supplied brackets to the CI-600 to mount in a rack. See the figure.

Fiber washer

M5 tapping screw

M3 binding head screw

M3 washer

2. Desk-top applications

Attach the supplied rubber foot to the position indicated with a small hole (4 holes 2.4mm

in diameter) in the bottom plate.

INSTALLATION

CONNECTION

1. Input control connector and power supply

Use the connection cable YR-806

(100cm in length) for connection

between the CI-600 and

exchange. When placing the

CI-600 on the exchange, use the

YR-802 cable (40cm).

Use the YR-803 or YR-807 cable

to connect the CI-600 to other

equipment.

For input control connector, use

either CN-1 or CN-2. They are

internally connected in parallel.

2. Speech IN/OUT terminals

Connect the IN/OUT terminals to the BX-610 or BX-620 terminal box as illustrated below.

IN 2 to No. 215 (upper row)

OUT 2 to No. 215 (lower row)

To other equipment

YR-802 or YR-806

Interface connector

CI-600

Be sure to insert the SI-62

Speech Interface card into the

second slot of a opening

allocated to the LM unit.

BX-610/BX-620

3. RS-232C connector

Connection between CI-600 and DEC VT-100 terminal

Connect the DEC terminal and CI-600 using the appropriate cable for distance between

the two. The type of connector is D-sub 25 pins (male) and D-sub 25 pin (female).

RS-232C 25-pin connector

M : Male connector

F : Female connector

[Connection diagram]

RS-232C

25-pin

connector

DEC terminal

RS-232C

Connection between IBM personal computer and CI-600

Connect the IBM personal computer and CI-600 using the appropriate cable for distance

between the two. The type of connector is D-sub 25 pins (male) and D-sub 25 pins

(female).

RS-232C 25-pin connector

[Connection diagram]

M : Male connector

F : Female connector

Personal computer

RS-232C

Connection between Cl-600s (tie-line connection)

In a tie-line system, connect one Cl-600's RS-232C connector No.2 t o the same connector

of another CI-600 only when initial set-up is performed.

(Refer to the operating instructions.)

[Connection diagram]

BACK-UPBATTERY

The Ni-Cd battery (GB50-3FA1) maintains the Cl-600's stored data during power failure.

Observe the following precautions.

To keep the battery fully charged, do not switch power off for first 8 days

after installing the Cl-600. Once the battery has been fully charged, it maintains

the stored data for about 10 days (at 25°C) even no power is supplied.

Expected battery life is about 2 years (at 25°C). Replace the battery every 2 years.

INITIAL CHECK-UP OF CI-600

START

Connect IN/OUT lines, power lines and speech IN/OUT lines to both the exchange and CI-600.

Using the RS-232C cable, connect Cl-600's RS-232C connector No. 1 to

personal computer or data terminal.

Set both MODE SELECT and BAUD RATE DP switches.

(Refer to the operating instructions.)

Set personal computer or data terminal in accordance with the Cl-600's

format. (Refer to the operating instructions.)

• Make sure that power is

supplied.

• Set reset switch (MODE

SELECT switch No.7) to ON.

Switch on the CI-600.

Does the timer LED blink at

1-second interval ?

YES

Does the monitor display initial set-up menu ?

YES

Can characters typed from a

keyboard be correctly displayed

on the screen ?

Confirm that the RS-232C

connector is connected properly.

YES

Recheck if MODE SELECT

switch NQ 7 is set to OFF. *

Confirm that the communication

format of personal computer or

data terminal matches that of

CI-600.

The section "Initial setting" of

operating instructions.

IMPORTANT

Leaving the switch on will cancel all

the stored data when power is

switched again.

Rack mounting bracket

Rack mounting screw (M5×12)

Fiber washer

Binding head screw (M3×6)

Washer (M3)

Rubber foot

Floppy disk

ACCESSORIES

SPECIFICATIONS

Specifications are subject to change without notice.

133-06-174-50

Operating power voltage

Current consumption

Terminal capacity

IN-OUT

connector/terminal

Standard

Message capacity

Recording & reproduction

Ambient temperature

Dimensions

Weight

24V DC (20-28V)

Less than 300mA

Interface bus

RS-232C

Speech IN/OUT/power unit

RS-232C

1.5-sec message×10

0.75-sec message × 10 (Total 22 sec)

ADM method

0°C~40°C

432(W)×44.5(H)×298CD)mm

(17(W)×1.8(H)×11.7(D) inch)

3.3kg (7.3 lbs)

Altri manuali per CI-600

Indice

Manuali Apparecchiature di registrazione popolari di altre marche

KV2 Audio

KV2 Audio 500 Series Manuale utente

Robotics Technologies

Robotics Technologies microBus-Cam II Manuale utente

Seca

Seca 460 Manuale utente

Cognex

Cognex MVS-8000 Series Manuale utente

Mect

Mect MPNC006 Series Manuale utente

Bad Caf

Bad Caf THE LEASH Manuale utente

Strymon

Strymon NIGHTSKY Manuale utente

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuale utente

Tews Technologies

Tews Technologies TPMC465 Manuale utente

Honeywell

Honeywell Excel 50 Manuale utente

SeaLevel

SeaLevel COMM+8.LPCI Manuale utente

Arturia

Arturia AUDIOFUSE STUDIO Manuale utente

Rukra

Rukra RK-1240 Manuale utente

Samson

Samson SCOM Manuale utente

Dynacord

Dynacord DPS260 Manuale utente

Nice

Nice Core Manuale utente

Pyle Pro

Pyle Pro PSS8 Manuale utente

RF-System

RF-System TinyGate Manuale per l'uso e la cura