Tohnichi CTA2-G Manuale utente

CTA2-G,Torque & Angle Wrench

Quick Start

1) Install and charge battery using Tohnichi charger until green light goes on.

2) Set on stable surface (do not move), Power ON ,wait for GOOD

3) Using arrow keys set counter to “000”

4) Press “MD” key for 2 seconds to enter set up menu

5) Setup Menu Select using arrow keys and save by pressing MEM key

SEL Mode-S (Single) or Mode-P (Production)

USEL Select Unit N*m, Kg*fm/Kg*fcm,Ft*lbs/In*lbs

Sng Set snug torque value

An Set angle value

AN-H Set angle upper limit

tUrn Set measurement direction CW or CCW

Ar Auto Reset set time 0.00 = OFF or0.1~5.0 seconds

bU Keypad beeping On/Off

PoFF Auto Power Off, 3min.or 10, 30 or None

do Data Output:, PC, or PRN (printer),

bpS Baud Rate: 9600 or 2400, 4800, 19200

dL Data length 8bit or 7 bit

Prt Parity Even or Odd

dFLt DFT-N donot reset or DFT-Y reset defaults

rtC1 Set Clock (Hour/Month/Second)

Single Tightening Mode

•Move counter off of “000” onto count

•Tighten to snug torque value, buzzer sounds

•Shifts into angle mode; intermittent buzzer warns when approaching set angle (within 20 degrees)

•Target angle alert with solid buzzer and blue LED light

•Release load and press MEM to judge within set range (in Auto reset mode judgment is made

automatically)

Production Tightening Mode (Once in P-Mode, need to reset mode using PC software)

•Set up through PC or on Keypad

•After following basic menu set up and selecting Mode-P

•Select Snug torque, 1st, 2nd, 3rd angle and upper limits for each

•Choose “n”= # of fasteners in the process

•Select: NG setting:

NG_RES=NG data then MEM & move to next

AL_RES= NG data then MEM to save tightening data and restart form beginning

•Press MEM key to start P-Mode, T screen appears to start. Complete process: D-OUT shows

•Press MD key or MEM to return to repeat process,

MD 2X=ALLOUT (go to PC software connect cable & select Data Upload)

MD 3X= D-CLR=delete 1 data, MD 4X=ALLCLR=delete all,

Press MD & C at same time to active

Download Data: Move to highest count included press MD key , STT is lower starting point, N= # data,

Press MEM to download

Deleting Data: Move count to select data, press C to delete one data. Move to highest count press MD

key, STT is lower starting point,

N= #data Press MD & C at same time to delete entire range.

Altri manuali per CTA2-G

1

Questo manuale è adatto per i seguenti modelli

6

Indice

Altri manuali Tohnichi Utensili elettrici

Tohnichi

Tohnichi DATA TORK CEM3-G Manuale utente

Tohnichi

Tohnichi PQLZ Manuale utente

Tohnichi

Tohnichi QL2N Manuale utente

Tohnichi

Tohnichi TiQL Manuale utente

Tohnichi

Tohnichi SP Manuale utente

Tohnichi

Tohnichi DB SERIES Manuale utente

Tohnichi

Tohnichi CTA2-G Manuale utente

Tohnichi

Tohnichi CEM3-P Manuale utente

Tohnichi

Tohnichi CL2Nx8D-MH Manuale utente

Tohnichi

Tohnichi YCL2 Manuale utente

Tohnichi

Tohnichi CTB10N2X8D-G Manuale utente

Tohnichi

Tohnichi MPQL Manuale utente

Tohnichi

Tohnichi CSPFHW Manuale utente

Tohnichi

Tohnichi QSPCA Series Manuale utente

Tohnichi

Tohnichi QSP Series Manuale utente

Tohnichi

Tohnichi MTQL Manuale utente

Tohnichi

Tohnichi CL2NX8D Manuale utente

Tohnichi

Tohnichi DATA TORK CEM3-G-WF Manuale utente

Tohnichi

Tohnichi WQL Series Manuale utente

Tohnichi

Tohnichi QLLS Manuale utente

Tohnichi

Tohnichi QL Manuale utente

Tohnichi

Tohnichi CLE2 Manuale utente

Tohnichi

Tohnichi SF Manuale utente

Tohnichi

Tohnichi QL25N Series Manuale utente

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale