Toko TMW1003 Manuale utente

11 Mbps Wireless LAN Access Point

Document version: 1.0

Document number: 004.doc

TMW1003UserManual

2version 1.0

FCC Regulation

INTERFERENCE INFORMATION: PART 15 OF FCC RULES

Some telephone equipment generates and uses radio frequency energy, which

if not properly installed, may cause interference to radio television reception.

This unit has been tested and found comply with the limits for a Class B

computing device in accordance with Part 15 of the FCC rules. These

specifications are designed to provide reasonable protection against such

interference in a residential installation.However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause interference to radio or television reception,

when it's in use, the user is encouraged to try to correct the interference by

one or more of the following measures:

A. Where it can be done safely, reorient the radio or TV receiving antenna.

B. To the extent possible, relocate the television, radio, or other receiver

with respect to telephone equipment.

C. If your telephone product runs on AC power, plug your product into an

AC outlet that's not on the same circuit as the one used by the radio or

television.

SAFETY INFORMATION

Your device contains a low power transmitter. When device is transmitted it

sends out radio frequency (RF) signal.

CAUTION: To maintain compliance with FCC’s RF exposure guidelines, this

equipment should be installed and operated with minimum distance 20cm

between the radiator and your body. Use on the supplied antenna.

Unauthorized antenna, modification, or attachments could damage the

transmitter and may violate FCC regulations.

004.doc 3

Contents

1 Getting started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

1.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.2 Contents of this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.3 Wireless LAN basics and advantages . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.4 Adding Access Points to your (network) environment . . . . . . . . . . . . . . 8

1.4.1 Creating a wireless network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

1.4.2 Extending a wired network with one or more Access Points . . . . . . . . 10

1.4.3 Connecting an Access Point directly to a computer . . . . . . . . . . . . . . . 11

2 Installing the Access oint . . . . . . . . . . . . . . . . . . . . . . . .13

2.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.2 Access Point environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.3 Physical installation of the Access Point . . . . . . . . . . . . . . . . . . . . . . . 13

2.4 Desktop installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2. Wall mount installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2.6 Connecting the Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.6.1 Power adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.6.2 UTP port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.7 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

2.8 Unlocking the Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

2.8.1 Unlocking the Access Point to reconfigure . . . . . . . . . . . . . . . . . . . . . . 18

2.8.2 Resetting to the default factory setting . . . . . . . . . . . . . . . . . . . . . . . . . 19

3 Configuring the Access oint . . . . . . . . . . . . . . . . . . . . .21

3.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.2 When to configure the Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . 21

3.3 Starting the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4version 1.0

Contents

3.4 Using KickStart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

3.4.1 Installing KickStart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

3.4.2 Launch KickStart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

3.4.3 Select wireless ethernet device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

3.4.4 Device data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

3.4. Change IP settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

3.4.6 Static IP settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

3.4.7 Set Gateway address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

3.4.8 Changing IP settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

3.4.9 Ready to start the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

3.4.10 Web Interface is launched . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

3. Launching the Web Interface manually . . . . . . . . . . . . . . . . . . . . . . . . .2

3.6 Contents of the Web Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

3.6.1 Settings Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

3.6.2 Wireless Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

3.6.3 Security against unauthorized network access . . . . . . . . . . . . . . . . . . .27

3.6.4 To add a client to the exception list . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

3.6. To delete a client from the exception list . . . . . . . . . . . . . . . . . . . . . . . .29

3.6.6 Security against eavesdropping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

3.6.7 Change WEP settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

3.6.8 Security against unauthorized configuration . . . . . . . . . . . . . . . . . . . . .30

3.6.9 Identity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

3.6.10 IP Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31

4 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

4.1 If KickStart does not find the Access Point you are looking for . . . . . . .33

4.2 Browser starts but window stays empty . . . . . . . . . . . . . . . . . . . . . . . .34

5 Technical specifications 11 Mbps WLAN Access oint 35

.1 General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

.2 Radio specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

.3 Security specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

.4 Other specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

6 Regulatory notes and statements . . . . . . . . . . . . . . . . . .39

6.1 Wireless LAN, Health and Authorization for use . . . . . . . . . . . . . . . . . .39

6.2 Regulatory Information/disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

6.3 USA-FCC (Federal Communications Commission) statement . . . . . . .39

6.4 FCC Radio Frequency Exposure statement . . . . . . . . . . . . . . . . . . . . .40

6. FCC Interference Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

6.6 Export restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

6.7 Europe - EU R&TTE Declaration of Conformity . . . . . . . . . . . . . . . . . .41

6.8 Restricted Wireless LAN device use in EU . . . . . . . . . . . . . . . . . . . . . .42

004.doc 5

Contents

A TC and I settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

A.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

A.2 How do computers communicate in a network . . . . . . . . . . . . . . . . . . 4

A.2.1 IP address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

A.2.2 Subnet mask . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

A.2.3 IP address range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

A.2.4 Reserved addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

A.2. Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

A.2.6 MAC address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

A.3 IP configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

A.3.1 DHCP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

A.3.2 Auto IP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

A.4 Setting up a home network and connecting it to the internet . . . . . . . . 49

B Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

B.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

B.2 Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

B.3 The Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

B.4 Service Set ID (SSID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

B. Physics of an Access Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

B. .1 Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

B. .2 Data rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

B. .3 Regulatory Domain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

B. .4 Radio Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

B.6 Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

B.6.1 WEP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

6version 1.0

Contents

004.doc 7

1 Getting started

1.1 Introduction

Thank you for purchasing your 11 Mbps WLAN Access Point.

The package you have received contains the following items:

•user manual,

•11 Mbps WLAN Access Point,

•power adapter,

•CD containing configuration software and this manual.

1.2 Contents of this manual

Table 1-1 gives an overview of the contents of this manual.

Figure 1-1 11 Mbps WLAN Access Point

Table 1-1 Contents of this manual

Chapter When to read:

This chapter (“Getting

started”)

Read this chapter on how to implement

a Wireless LAN in your (network)

environment.

Chapter 2: ‘Installing the

Access Point’ on page 13

Read this for information on how to

install and connect Access Point to

your (network) environment.

8version 1.0

Getting started

Wireless LAN basics and advantages

1.3 Wireless LAN basics and advantages

A wireless LAN connects computers to each other using radio

technology. This offers you the freedom to move around the area and

work anywhere within radiographic reach of an Access Point.

The Access Points can be connected to a wired network. This allows

wireless clients to communicate with computers on the wired network.

The technology is an extension to the existing Ethernet networking

standard, so you can connect the Access Point to an existing Ethernet

network (for more detailed information on the standards supported, see

chapter : ‘Technical specifications 11 Mbps WLAN Access

Point’ on page 3 ).

1.4 Adding Access oints to your (network) environment

Where to place and how to connect an Access Point depends entirely on

your specific (network) environment. In this section some guidelines on

how to add Access Points to your environment are given.

Chapter 3: ‘Configuring the

Access Point’ on page 21

Read this chapter when you want to

adjust the settings of an Access Point.

This chapter will also explain when to

adjust the settings.

Chapter

4: ‘Troubleshooting’ on page

Read this chapter when the Access

Point does not function.

Chapter : ‘Technical

specifications 11 Mbps

WLAN Access

Point’ on page 3

This chapter contains the technical

specifications of the Access Point.

Appendix A: ‘TCP and IP

settings’ on page 4

This appendix contains background

information on TCP/IP settings and

other networking terminology.

Appendix B: ‘Wireless

LAN’ on page 1

This appendix contains some

background information on wireless

LANs.

Read this appendix when you are not

familiar with radiographic terminology

and wireless networking.

Table 1-1 Contents of this manual

Chapter When to read:

004.doc 9

Getting started Adding Access oints to your (network) environment

An Access Point can be used to

•create a wireless network (see section 1.4.1),

•extend an existing wired network (see section 1.4.2),

•connect to a single computer (see section 1.4.3).

1.4.1 Creating a wireless network

You can use an Access Point to set up a wireless network, see

Figure 1-2.

When you install a new wireless network, follow these steps:

1. Prepare one client (install wireless network card and software).

2. Select the IP settings of this client.

3. Install the Access Point.

You can now use the wireless network.

4. Optionally, configure the Access Point from the already configured

client using KickStart and the Web Interface (see chapter

3: ‘Configuring the Access Point’ on page 21).

5. Install other clients if this is applicable to your situation.

Figure 1-2 Wireless network

10 version 1.0

Getting started

Adding Access oints to your (network) environment

1.4.2 Extending a wired network with one or more Access oints

When your Access Point is an extension to a wired network, it is

recommended that you make sure that the wired network is completely

functional to exclude existing problems.

See Figure 1-3.

Follow these steps:

1. Install the Access Point and connect it to your wired network.

You can now use the wireless network.

2. Optionally, configure the Access Point from an existing computer in

the network using KickStart and the Web Interface (see chapter

3: ‘Configuring the Access Point’ on page 21).

3. Install the wireless client(s).

Figure 1-3 Adding an Access Point to a wired network

hub

wired network

Indice

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente

toko TMW1003 Manuale utente

Manuali Punto di accesso wireless popolari di altre marche