Toro DRIP ZONE VALVE KIT 53749 Manuale utente

Questo manuale è adatto per i seguenti modelli

1

Altri manuali Toro Sistema di irrigazione

Manuali Sistema di irrigazione popolari di altre marche

Hunter

Hunter Institutional Series Manuale utente

Cellfast

Cellfast 52-305 Manuale utente

Tyco Fire Product

Tyco Fire Product Star Galaxy SGQR Manuale utente

Tyco Fire Product

Tyco Fire Product CENTRAL A Manuale utente

Oral Care Technologies

Oral Care Technologies Hydro Floss Manuale utente

Reliable

Reliable F1-300 Manuale utente

Tyco Fire Product

Tyco Fire Product Gem F892 Manuale utente

Netafim

Netafim NETBEAT Manuale utente

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Manuale utente

Tyco

Tyco CC3 Manuale utente

Reliable

Reliable F4FR Manuale utente

OpenSprinkler

OpenSprinkler OSPi Manuale utente

EINHELL

EINHELL GE-WW 5537 E Manuale utente

Valley

Valley Bender160 Manuale utente

Reliable

Reliable F1FR42 Series Manuale utente

Reliable

Reliable F1FR-300 Manuale utente

Eden

Eden 97063-EDAMZ Manuale utente

Tyco

Tyco TY-L Series Manuale utente

Installation Procedure

CAUTION:

When assembling the Drip Zone Valve

Kit components, use just 11⁄2to 2 turns of Teflon

tape on male threads. Never use pipe dope.

To achieve a leak-free thread connection, turn the

male fitting until it is finger tight, then add one or

two more turns. Over-tightening can cause splitting

and failure of the female threads.

Important: Ensure the Y-Filter, Jar Top Valve and

Pressure Regulator are installed in the correct flow

orientation. Flow direction arrows are provided on each

component. Refer to Figure 1 and Figure 2.

1. Using the Close Nipple, install the Ball Valve to the Jar

Top Valve inlet.

2. Remove the Bonnet Ring from the Y-Filter by turning

it counterclockwise. Remove the Bonnet and Filter

Screen. See Figure 1.

3. Install the Y-Filter inlet to the Jar Top Valve outlet.

4. Install the Pressure Regulator inlet to the Y-Filter outlet.

5. Reassemble the Y-Filter components.

Note: Hand tighten the Bonnet Ring only – do not

over-tighten.

Important: Refer to the provided Toro Jar Top Valve,

Anti-Siphon (AVB) installation instructions for additional

important installation and operating information.

6. To determine the recommended minimum/maximum

number of drip emitters per Jar Top valve, refer to the

table below.

For technical assistance, call 1-800-367-8676.

Kit Components

• 3/4" (FPT X FPT) Ball Valve

• 3/4" (MPT X MPT) F Series Y-Filter, 150 Mesh

• 3/4" (FPT X FPT) Toro Jar Top Valve, Anti-Siphon (AVB)

• 3/4" NPT Close Nipple

• 3/4" (FPT X FPT) Pressure Regulator, 25 PSI at 0.25–8 GPM

Drip Zone Valve Kit

Model 53749

Installation Instructions

Specifications

• Inlet/Outlet Pipe Connection: 3/4" Female NPT

• Maximum Supply Pressure: 150 PSI

• Downstream Pressure Regulation: 25 PSI

• Flow Rate @ 25 PSI: 0.25–8 GPM

• Filtration: 150 Count Stainless Mesh Screen

• Irrigation Control Valve:

• Automatic, Anti-Siphon, Toro Jar Top Model

• Manual Bleed and Flow Control

• 24 V a.c., 60 Hz Solenoid

Bonnet Ring

Bonnet

Filter Screen

Jar Top Valve

Y-Filter

Ball Valve

From Water

Supply To Emitters

Pressure

Regulator

Close Nipple

Body

Note: Valve must be

installed at least 6"

above the highest

emitter it controls.

Figure 2

Figure 1

© 2005 The Toro Company, Consumer Division • An ISO 9000-certified Company Form Number 373-0347 Rev. B

P.O. Box 489, Riverside CA, 92502 • www.toro.com