Toro Greensmaster 3000 Series Manuale

Altri manuali per Greensmaster 3000 Series

2

Questo manuale è adatto per i seguenti modelli

2

Altri manuali Toro Taglia erba

Manuali Taglia erba popolari di altre marche

RHINO

RHINO 1958 Manuale utente

Wolf Garten

Wolf Garten Compact plus 40 B Manuale utente

Cub Cadet

Cub Cadet LTX 1045 Manuale utente

Craftsman

Craftsman 917.378461 Manuale utente

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manuale utente

Challenge

Challenge CH18V2 Istruzioni operative

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manuale utente

DEWEZE

DEWEZE ATM-725 Manuale operativo

Weed Eater

Weed Eater 180083 Manuale utente

Husqvarna

Husqvarna Poulan Pro PP185A42 Manuale utente

Better Outdoor Products

Better Outdoor Products Quick Series Manuale utente

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manuale operativo

MTD

MTD 795, 792, 791, 790 Manuale utente

Dennis

Dennis FT 610 Manuale utente

AIRFORCE

AIRFORCE F-15 Gen 3 Manuale utente

MTD

MTD 126-220-000 Manuale utente

Stihl

Stihl RMA 443 PV Manuale utente

Yard-Man

Yard-Man 3700-0 Manuale utente

 2004—TheToro Company

8111 Lyndale Ave., Bloomington, MN 55420, USA Printed in the USA

All Rights Reserved Original Instructions (EN)

Register your product at www.Toro.com

8 and 11 Blade DPA Reel Mowers

Greensmaster 3000 Series

Model No. 04610—230000001 and Up

Model No. 04611—230000001 and Up

Form No. 3351-557

Setup Instructions

Attention!

You must perform the following procedures on the designated traction units before you

install the cutting units.

Greensmaster 3050 Serial No. 230001501 & Prior

Greensmaster 3100 Serial No. 220001501 & Prior

Greensmaster 3150 Serial No. 230001000 & Prior

Mounting the Pull Arm

Bumpers

Order (6) Bumpers, Part No. 94-4548 and (6) Washer

Head Self Tapping Screws, Part No. 32144-44 from your

local Toro Distributor. Bumper may have already been

mounted to pull frame.

1. Using the dimensions shown in Figure 1, locate, mark,

and drill two .221 in. diameter holes in the underside

of each pull frame cross tube.

Note: Holes may already be present in the cross tubes.

1

19.43 in.

3.54 in. 0.75 in.

Figure 1

1. Pull frame cross tube

2. Mount the 2 recessed bumpers to the underside of each

pull frame cross tube with 2 washer head self tapping

screws (1/4 x 3/4 in.) (Fig. 2).

1

Figure 2

1. Recessed bumper

Modifying the Baskets

1. Locate and mark cut-off lines on each side of basket,

as shown in Figure 3.

1

Figure 3

1. Cut-off line

2

2. Using a sharp knife or similar cutting tool, cut off

material at marks.

3. Repeat procedure on all baskets.

Greensmaster 3250 Serial No. 230001500 & Prior

Modifying the Baskets

1. Using dimensions shown in Figure 4, locate and mark

cut–off lines on each side of basket.

.50”

2.00”

1

.50”

radius

Figure 4

1. Cut–off line

2. Using a sharp knife or similar cutting tool, cut off

material at marks.

Important Do not make a sharp corner; cut to form

a radius of approximately 1/2 in.

3. Repeat procedure on all baskets.

Replacing the Pull Arm

Extension

Order (6) Pull Arm Extensions, Part No. 99-4270 from

your local Toro Distributor.

1. Lower cutting units to the ground.

2. Loosen jam nuts and remove existing pull arm

extension from pull arms and ball joint receivers on all

carrier frames (Fig. 5).

1

3

2

Figure 5

1. Pull link extension

2. Pull arm 3. Ball joint receiver

3. Install new longer pull arm extensions to pull arms and

ball joint receivers (Fig. 6).

4. Adjust pull arm extensions to attain dimension shown

in Figure 6. Tighten jam nuts.

5. Mount the basket onto the carrier frame.

6. Adjust the pull links until there is 1/4 to 3/8 in. (6 to

9 mm) clearance between the lip of the basket and the

reel blades. Make sure the basket lips are equidistant

from the reel blades all the way across the reel blades.

1

6.62 in. (168 mm)

Figure 6

1. Pull link extension