Toro Reelmaster 5100-D Manuale utente

Using the Diagnostic ACETM

Reelmaster® 5100-D/5300-D

Part No. 92800SL, Rev. B

Commercial Products

Controller Diagnostic Lamp

NOTE: Part number under CONTROLLER DIAGNOSTIC LAMP is the decal part

number; not the lamp. The lamp part number is 85-4491

If the machine malfunctions, check the green Controller Diagnostic

Lamp. If the lamp is

, with ignition key switch in ON position, the

electronic control unit (ECU) is functioning normally. If the lamp is

blinking,thecontrollerhasdetectedaproblemintheelectricalcircuit.

The lamp will stop blinking and automatically reset when the key

switch is turned OFF.

If Controller Diagnostic Lamp is

BLINKING ON

and

OFF

1. ECU has detected an output with a short circuit.

2. ECU has detected an output with an open circuit.

Use Diagnostic ACETM to find which output is malfunctioning.

NOTE: If the green Controller Diagnostic Lamp is blinking on and

off, connect the Diagnostic ACE, without turning the key switch off,

then toggle to “OUTPUTS DISPLAYED”. The blinking LED on the

DiagnosticACEwillindicatewhichoutputisfaulty.Tostoptheengine

without turning off the key switch, use the manual fuel stop lever on

the injection pump or grasp the steering wheel, raise yourself up off

the seat and lightly push the traction pedal so the interlock circuit

stops the engine.

If the controller diagnostic lamp is

OFF

1. ECU is not powered on.

2. Loop-back connector is not attached.

3. Diagnostic lamp is burned out.

4. ECU is not functioning correctly.

Checkelectricalconnections,inputfusesand diagnosticlamptofind

malfunction. Make sure loop-back connector is secured to wire

harness connector.

Using the Diagnostic ACE (RM 5100-D/5300-D) Page 1

Installing Diagnostic ACETM

1. Park machine on a level surface, engage parking brake, lower

cutting units and turn ignition key switch OFF.

2. Carefully disconnect loop-back connector from wire harness.

3. Connect Diagnostic ACE to connector on wiring harness (where

loop-back connector was removed).

Disconnect loop-back connector

and connect Diagnostic ACE Display

Using the Diagnostic ACE (RM 5100-D/5300-D) Page 2

1.AfterconnectingDiagnosticACEandturningkeyswitchON,move

any input switch, such as the Enable/Disable switch, to get the

Diagnostic ACE display to function. DO NOT start the engine.

CAUTION: To prevent possible personal injury, lower

cutting units before working on machine. If ignition key

switch is on, cutting units will lower when joystick is moved to

lower/mow position.

NOTE: After doing step 1, the “INPUTS DISPLAYED” LED will be on.

This indicates that the ECU and Diagnostic ACE are operating

properly. If the green Controller Diagnostic Lamp on the machine

comeson,butthe“INPUTSDISPLAYED”LEDdoesnotcomeon,there

is a problem with the Diagnostic ACE.

2. If necessary, push input-output toggle button so “INPUTS

DISPLAYED” LED is on. Do not hold the button down.

NOTE: Red text on overlay decal refers to input switches and green

text to outputs.

3. The Diagnostic ACE will illuminate the LED associated with each

input when that input switch is closed. Check each switch (input) by

openingandclosingtheswitch,thenverifyingthatthecorresponding

LED goes onand offas the switch positionis changed. Forexample,

with traction pedal in neutral, “TR.NEUTRAL” LED should be on, then

go off, when traction pedal is moved out of neutral. Check function

for each switch that can be changed manually.

4.Ifa switchis closedand correspondingLED does notgoon,check

all wiring and connections to switch and/or test switch with a

continuity tester or ohm-meter. Replace any faulty switches and

repair or replace any faulty wiring or connectors.

Checking INPUTS

Push INPUT-OUTPUT TOGGLE

so INPUTS DISPLAYED light is ON.

Using the Diagnostic ACE (RM 5100-D/5300-D) Page 3

INPUT – KEY RUN

Using the Diagnostic ACE (RM 5100-D/5300-D) Page 4

INPUT – TR. NEUTRAL

Using the Diagnostic ACE (RM 5100-D/5300-D) Page 5

INPUT – SEAT SWITCH

Using the Diagnostic ACE (RM 5100-D/5300-D) Page 6

INPUT – ENGINE HOT

To test, disconnect

and ground terminal

to engine block.

Using the Diagnostic ACE (RM 5100-D/5300-D) Page 7

INPUT – RAISE

Using the Diagnostic ACE (RM 5100-D/5300-D) Page 8

Altri manuali per Reelmaster 5100-D

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Toro Taglia erba

Toro

Toro 22045 Manuale utente

Toro

Toro GrandStand 74504 Manuale utente

Toro

Toro STRIPE 21620 Manuale utente

Toro

Toro 74629 Manuale utente

Toro

Toro Proline 30138 Manuale utente

Toro

Toro 74571 M74571 Manuale utente

Toro

Toro TimeCutter Z5020 Manuale utente

Toro

Toro 20959 Manuale utente

Toro

Toro 30722 Groundsmaster 300 Manuale utente

Toro

Toro Recycler 20990 Manuale utente

Toro

Toro Flex-Force Power System 21863 Manuale utente

Toro

Toro 78452 Manuale utente

Toro

Toro Z Master 8000 Series Manuale utente

Toro

Toro TurfMaster 22205TE Manuale utente

Toro

Toro 30821 Manuale utente

Toro

Toro Haven 20459 Manuale utente

Toro

Toro 74301 Manuale utente

Toro

Toro 04022 Greensmaster Flex 21 Manuale utente

Toro

Toro 74637 Manuale utente

Toro

Toro 75210 Manuale utente

Toro

Toro 74675 Manuale utente

Toro

Toro 70185 Manuale

Toro

Toro TITAN HD 1500 Manuale utente

Toro

Toro 22298 Manuale utente

Manuali Taglia erba popolari di altre marche

RHINO

RHINO 1958 Manuale utente

Wolf Garten

Wolf Garten Compact plus 40 B Manuale utente

Cub Cadet

Cub Cadet LTX 1045 Manuale utente

Craftsman

Craftsman 917.378461 Manuale utente

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manuale utente

Challenge

Challenge CH18V2 Istruzioni operative

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manuale utente

DEWEZE

DEWEZE ATM-725 Manuale operativo

Weed Eater

Weed Eater 180083 Manuale utente

Husqvarna

Husqvarna Poulan Pro PP185A42 Manuale utente

Better Outdoor Products

Better Outdoor Products Quick Series Manuale utente

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manuale operativo

MTD

MTD 795, 792, 791, 790 Manuale utente

Dennis

Dennis FT 610 Manuale utente

AIRFORCE

AIRFORCE F-15 Gen 3 Manuale utente

MTD

MTD 126-220-000 Manuale utente

Stihl

Stihl RMA 443 PV Manuale utente

Yard-Man

Yard-Man 3700-0 Manuale utente