Toro Workman 07170 Manuale utente

Form No. 3463-630 Rev A

60V Electric Lift Kit

W orkman

Lithium GTX Utility V ehicle

Model No. 07170

Installation Instructions

Note: Reuse any mounting hardware that you removed and is not replaced with hardware from the kit.

Preparing the Machine

1. Park the machine on a level surface.

2. Engage the parking brake.

3. Shut of f the machine and remove the key .

g038447

Figure 1

Removing the Gas Spring and Lift Bracket

Machines with a Steel Cargo Bed Only

W ARNING

A raised cargo bed could fall and injure persons that are working beneath it.

• Remove any load material from the bed before raising it.

• Always properly support the bed in the raised position before working under the bed.

81 1 1 L yndale A venue South

Bloomington, MN 55420

Original Instructions (EN)

Printed in the USA

*3463-630*

1. Raise the cargo bed.

2. Remove the gas spring as shown in Figure 2 .

g441 139

Figure 2

3. Remove the lift bracket as shown in Figure 3 .

g441431

Figure 3

Placing the Bed into the Service Position

Machines with a Plastic Cargo Bed Only

Note: If the draw bar is installed on the machine, you must remove it before placing the bed into the service

position.

Insert the prop rod into the service position ( Figure 4 ).

g036022

Figure 4

Installing the Lift Bracket

5x 5x

1. Remove the existing bolt and nut from the rear-frame tube (box A of Figure 5 ).

Note: Discard the bolt and nut.

2. Remove the 2 existing plastic rivets from the rear-frame tube (box B of Figure 5 ).

Note: Retain the 2 plastic rivets.

3. Install the lift bracket to the rear-frame tube using the 5 ange-head bolts (3/8 x 2-1/2 inches) and 5

ange nuts (3/8 inch) as shown in box C of Figure 5 .

T orque the ange-head bolts (3/8 x 2-1/2 inches) to 37 to 45 N∙m (27 to 33 ft-lb).

4. Install the 2 previously removed plastic rivets into the rear frame tube (box D of Figure 5 ).

g381446

Figure 5

Installing the Lift Latch

1. Remove the 2 existing bolts from the cargo bed lever (box A of Figure 6 ).

2. Install the lift latch to the cargo bed lever using the 2 previously removed bolts, and torque the bolts to 15

to 16 N∙m (1 1 to 12 ft-lb) as shown in box B of Figure 6 .

g035996

Figure 6

Installing the Lift Plate

Machines with a Plastic Cargo Bed Only

1x 6x

1. Remove the 6 existing bolts and bed braces from the cargo bed (box A of Figure 7 ).

Note: Discard the bolts and bed braces.

2. Install the lift plate to the cargo bed using the 6 bolts, and torque the bolts to 15 to 16 N∙m (1 1 to 12

ft-lb) as shown in box B of Figure 7 .

g035960

Figure 7

Installing the Fuse

Install the fuse (20 A) into the fuse block as shown in Figure 8 .

g441 159

Figure 8

Installing the Relays

2x 2x

Install and connect the relays as shown in Figure 9 .

g441 158

Figure 9

Installing the Switch

1. Cut out the opening in the dashboard decal for the switch (box A of Figure 10 ).

2. Install the switch connector through the opening in the dashboard (box B of Figure 10 ).

3. Install the switch to the switch connector (box C of Figure 10 ).

4. Ensure that the switch is oriented properly (box D of Figure 10 ).

g378587

Figure 10

Installing the Lift Cylinder

1x 2x 2x 1x

Important: Use the cable tie to secure the lift-cylinder wire to the wire harness, away from sharp or

moving parts. Ensure that you allow enough slack in the wire harness for its full range of motion.

1. Install the lift cylinder using a clevis pin and hairpin cotter (box A of Figure 1 1 ).

2. Connect the wire harness and secure it to the machine rail using the cable tie (box B of Figure 1 1 ).

3. Rotate the lift cylinder upward to a 45° angle, then use a block to support the lift cylinder (box C of

Figure 12 ).

4. Press upward on the switch to extend the lift cylinder (box D of Figure 12 ).

5. Install the extended portion of the lift cylinder to the cargo bed using a clevis pin and hairpin cotter (box

E of Figure 12 ).

T op half—plastic cargo bed; bottom half—steel cargo bed

g036021

Figure 1 1

Indice

Altri manuali Toro Veicolo utilitario

Manuali Veicolo utilitario popolari di altre marche

Polaris

Polaris ACE 900 SP Manuale utente

TrailMax

TrailMax T-12-UR Manuale utente

Floe

Floe Cargo Max 9.5-73 Manuale utente

Taylor-Dunn

Taylor-Dunn B0-050-00 Manuale

Taylor-Dunn

Taylor-Dunn ET 3000 Manuale utente

Kayo

Kayo S70 Manuale utente

Range Road

Range Road RR608 Manuale utente

Landoll

Landoll 900D Series Manuale utente

pronovost

pronovost PUMA-10000 Manuale utente

SSI SCHAEFER

SSI SCHAEFER WEASEL LITE Manuale utente

Club Car

Club Car TURF 272 2005 Manuale

Cushman

Cushman Turf Truckster 84069 Manuale utente

BERG

BERG Large Trailer Manuale utente

Cub Cadet

Cub Cadet Big Country 641 Manuale utente

Westward

Westward Go-4 XTR Manuale utente

Club Car

Club Car Carryall I 1999 Manuale utente

Etnyre

Etnyre Street Flusher Manuale di istruzioni

Landoll

Landoll 340 Manuale utente