Toshiba TS3000 Series Manuale utente
STE 80756–2
６
TS3000 SCARA / LINEAR system
TS3100 SCARA / LINEAR / 6-AXIS system
TSL3000 SCARA system
INSTRUCTION MANUAL
FIELD BUS SLAVE FUNCTION MANUAL
Notice
1. Make sure that this instruction manual is delivered to the final
user of Toshiba Machine's industrial robot.
2. Before operating the industrial robot, read through and
completely understand this manual.
3. After reading through this manual, keep it nearby for future
reference.
TOSHIBA MACHINE CO., LTD.
NUMAZU, JAPAN
FIELD BUS SLAVE FUNCTION MANUAL
series Robot Controller
Copyright 2012 by Toshiba Machine Co., Ltd.
All rights reserved.
No part of this document may be reproduced in any form without obtaining prior written
permission from Toshiba Machine Co., Ltd.
The information contained in this manual is subject to change without notice to effect
improvements.
- 1 - STE 80756
FIELD BUS SLAVE FUNCTION MANUAL
series Robot Controller
Preface
This manual describes the initial setting procedures and operating method of the field
bus slave function, the TS3000/TS3100/TSL3000 (referred to as TS3000 series below)
robot controller extension function. It is intended for users with general knowledge of
field bus.
The slave module for the field bus can select either of the three (3) types; PROFIBUS,
DeviceNet or CC–Link, which should be determined at order entry.
The field bus input signals are assigned to DIN301 to DIN364 and DIN401 to DIN464,
and the output signals are assigned to DOUT301 to DOUT364 and DOUT401 to
DOUT464. Also, the Simple PLC Function (option) can be used to enable changing of
the I/O and routing of the system signal I/O through the field bus.
Instruction manuals which are referred to from this manual
• Robot language manual
• Operation manual
• User parameter manual
• Maintenance manual
• Instruction manual of master station you wish to use
- 2 - STE 80756
FIELD BUS SLAVE FUNCTION MANUAL
series Robot Controller
!CAUTION
This manual does not contain any detailed descriptions
on power and robot connection.
For the connection of the power and robot, see the
Installation & Transport Manual.
Cautions on Safety
This manual contains the important information on the robot and controller to prevent
injury to the operators and persons nearby, to prevent damages to assets and to assure
correct use.
Make sure that you well understand the following details (indications and symbols)
before reading this manual. Always observe the information that is noted.
[Explanation of indications]
Indication Meaning of indication
!DANGER
This means that "incorrect handling will lead to fatalities or
serious injuries."
!CAUTION
This means that "incorrect handling may lead to personal
injuries 1) or physical damage 2)."
•Injuries refer to injuries, burns and electric shocks, etc., which do not require
hospitalization or long-term medical treatment.
•Physical damage refers to damages due to destruction of assets or resources.
- 3 - STE 80756
FIELD BUS SLAVE FUNCTION MANUAL
series Robot Controller
[Explanation of symbols]
Symbol Meaning of symbol
This means that the action is prohibited (must not be done).
Details of the actions actually prohibited are indicated with
pictures or words in or near the symbol.
This means that the action is mandatory (must be done).
Details of the actions that must be done are indicated with
pictures or words in or near the symbol.
!
This means danger.
Details of the actual danger are indicated with pictures or words in
or near the symbol.
!
This means caution.
Details of the actual caution are indicated with pictures or words in
or near the symbol.
!CAUTION
To perform the work ranging from robot installation to
operation with safety, read through and through the Safety
Manual provided separately before actually starting the
work.
- 4 - STE 80756
FIELD BUS SLAVE FUNCTION MANUAL
series Robot Controller
Maintenance and Inspection
To use the robot safety, strictly observe the following matters.
!DANGER
Prohibited
• NEVER burn, disassemble or charge the battery. Otherwise,
it may explode.
Mandatory
• Before performing the maintenance and inspection, be sure to
turn off the main power switch of the controller.
• When disposing of batteries, be sure to follow the user's
regulations.
!CAUTION
Disassembly
prohibited
• The user should NEVER replace or change parts other than
those stipulated in the instruction manual. Otherwise, the
performance will deteriorate, resulting in troubles.
Mandatory
• To replace parts, use the spare parts designated by Toshiba
Machine.
• Carry out the maintenance and inspection on a regular basis.
Otherwise, the equipment may go wrong or accidents will be
caused.
!CAUTION
To perform the maintenance and inspection of the robot
with safety, read through and through the Maintenance
Manual provided separately before actually starting the
work.
- 5 - STE 80756
FIELD BUS SLAVE FUNCTION MANUAL
series Robot Controller
Table of Contents
Page
1. Operation Flow......................................................................................................... 7
2. Hardware Structure .................................................................................................. 9
2.1 Field Bus Printed Board Assembling Procedures to the TS3000/TS3100
Controller....................................................................................................... 9
2.2 Installing the Printed Board in the TSL3000 Controller................................ 12
2.3 Connection................................................................................................... 14
2.3.1 Pin Array of Connector for Connecting External Equipment........... 14
2.3.2 Connection ..................................................................................... 16
3. Field Bus Slave Module.......................................................................................... 17
3.1 PROFIBUS Slave Module Specifications..................................................... 17
3.1.1 PROFIBUS Specifications.............................................................. 17
3.1.2 Setting of PROFIBUS User Parameter........................................... 18
3.2 DeviceNet Slave Module Specifications....................................................... 20
3.2.1 DeviceNet Specifications................................................................ 20
3.2.2 Setting of DeviceNet User Parameter............................................. 21
3.3 CC–Link Slave Module Specifications ......................................................... 23
3.3.1 CC–Link Specifications................................................................... 23
3.3.2 Setting of CC–Link User Parameter ............................................... 24
4. Error Detection ....................................................................................................... 26
5. Verifying Motion...................................................................................................... 27
6. How to Use SCOL Language Instruction................................................................ 30
6.1 Sample Program.......................................................................................... 31
- 6 - STE 80756
FIELD BUS SLAVE FUNCTION MANUAL
series Robot Controller
1. Operation Flow
The operation flow to enable the field bus interface is given below.
* When specifying the Field Bus during the purchase of the robot controller, read the
step (2) Connecting with the master station and skip to step (4) Setting the master
station and go to later steps.
(1) Mounting the field bus ··· See Section 2 of this manual.
Mount the field bus you procured on the controller.
Uncover the controller and perform the manual work.
Before starting this work, be sure to turn the power off.
When you already specified the field bus at order entry of the robot, the bus is
factory-set. Make sure of it.
To proceed with the next process, the controller should remain uncovered.
⇓
(2) Connecting with the master station ··· See Section 2 of this manual.
Connect the field bus terminal on the controller side with the field bus cable
connecting to the master station.
⇓
(3) Setting the controller parameters ··· See Section 3 of this manual, the
operation manual and user parameter manual.
Turn on the controller power, edit the [U16 FIELD BUS] parameter contained
in the user parameter (USER.PAR) file.
The user parameter becomes operative after the power is turned off once,
then on again.
⇓
(4) Setting the master station ··· See Section 3 of this manual and the master
station instruction manual.
Perform setting of the master station. The setting procedures differ with the
master station to be used. Refer to the master station instruction manual you
procured.
⇓
- 7 - STE 80756
FIELD BUS SLAVE FUNCTION MANUAL
series Robot Controller
⇓
(5) Confirming the operation ··· See Section 5 of this manual and the master
station instruction manual.
The power is turned on in order of “First Field Bus master” and “Robot
controller”.
To make sure that the I/Os assigned to the robot controller can be operated
properly, set ON the switch assigned from the master station and monitor the
I/O status from the robot controller. Also, set ON the switch on the robot
controller side and monitor the I/O state from the master station to make sure
that the information can be transmitted legally.
If an error has generated, investigate the error information from the master
station.
⇓
(6) Creating the robot program and verifying the control ··· See Section 6 of this
manual and the master language instruction manual.
Create the robot program, referring to the example of robot program creation
and make sure that the I/Os on the field bus can be controlled, using the
SCOL language.
⇓
(7) Finish of the work
Now the work has finished. Turn off the controller power and cover the
controller.
- 8 - STE 80756
FIELD BUS SLAVE FUNCTION MANUAL
series Robot Controller
2. Hardware Structure
2.1 Field Bus Printed Board Assembling Procedures to the TS3000/TS3100
Controller
Assemble the Field Bus printed board in the manner described below.
(1) Turn off the power of the robot controller.
(2) Turn off the main power of 200V supplied to the robot controller.
Disconnect the power connector (ACIN–CN1) to assure safety.
(3) Remove the top cover of the robot controller.
This top cover is secured with a total of twelve (12) screws (M3 ×6) (eight (8)
screws each on the both lateral sides and four (4) screws on the top side of the
robot controller. Remove the screws, using a screwdriver, then draw the cover to
side and remove.
Fig. 1 Removing the TS3000/TS3100 Cover
- 9 - STE 80756
Altri manuali per TS3000 Series
9
Questo manuale è adatto per i seguenti modelli
3
Indice
Altri manuali Toshiba Controllori
Toshiba
Toshiba T2E Manuale utente
Toshiba
Toshiba TCB-SC640U Manuale utente
Toshiba
Toshiba RBC-AWSU52-E Manuale utente
Toshiba
Toshiba TMP87CM24AF Istruzioni per l’uso
Toshiba
Toshiba TSL3000 Manuale utente
Toshiba
Toshiba TE3 Series Manuale utente
Toshiba
Toshiba Programmable Controller PROSEC T3 Manuale utente
Toshiba
Toshiba nv Series Manuale utente
Toshiba
Toshiba TSL3000 Manuale per l'uso e la cura
Toshiba
Toshiba BMS-IFBN1281U-E Manuale utente
Toshiba
Toshiba V Series Manuale utente
Toshiba
Toshiba RBC-MTSC1 Manuale utente
Toshiba
Toshiba TS2000 Manuale utente
Toshiba
Toshiba V Series Manuale utente
Toshiba
Toshiba RBC-MTSC2 Manuale utente
Toshiba
Toshiba T6963C Istruzioni per l'installazione e il funzionamento
Toshiba
Toshiba CONNECT Manuale utente
Toshiba
Toshiba nv Series Manuale utente
Toshiba
Toshiba V Series Manuale utente
Toshiba
Toshiba TS2000 Manuale utente
