TP-Link Auranet EAP220 Manuale utente
7106506404 REV1.0.0
Specifications are subject to change without notice. TP-LINK is a registered
trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product
names are trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any
means or used to make any derivative such as translation, transformation,
or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD.
Copyright © 2016 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.
www.tp-link.com
›English
› Български
› Čeština
› Қазақша
› Lietuvių
› Magyar
›Polski
› Русский язык
› Română
› Slovenčina
› Srpski jezik
› Українська мова
Ceiling Mount Access Point
Installation Guide
CONTENTS
English..................................................................................................1
Български ............................................................................................7
Čeština ...............................................................................................13
Қазақша .............................................................................................19
Lietuvių ...............................................................................................25
Magyar................................................................................................31
Polski..................................................................................................37
Русский язык .....................................................................................43
Română..............................................................................................49
Slovenčina..........................................................................................55
Srpski jezik .........................................................................................61
Українська мова ................................................................................67
1
English
Note: The image may differ from the actual product.
Network Topology
A typical network topology for the EAP is shown below.
EAP Controller
A DHCP server (typically a router) is required to assign IP addresses to the EAPs
and clients in your local network. A computer running the EAP Controller software,
which can be in the same or different subnet with the EAPs, is used to centrally
manage the EAPs.
You can get the EAP Controller software from our website http://www.tp-link.com.
Hardware Installation
■Option1：
Ceiling Rail Mounting
Follow the steps below to install the EAP with the provided accessories:
1Position the Ceiling T-rail Clip and push the
movable part toward the rail base.
Ceiling T-rail Clip M3×6 Pan-head Screws (Qty.5)
Controller
Host
Router Switch
Internet
Clients
EAP
EAP
EAP
2
English
2Use an M3×6 pan-head screw to secure the T-rail
Clip onto the ceiling rail.
3Attach the mounting bracket to the Ceiling T-rail
Clip using four M3x6 pan-head screws.
4Attach the EAP to the mounting bracket by
aligning ARROW 1 (on the EAP) with ARROW 2
(on the mounting bracket), then rotate the EAP
clockwise until it locks into place.
5Connect the Ethernet cable to the ETHERNET
port.
3
English
■Option2：
Ceiling Mounting
Follow the steps below to install the EAP with the provided accessories:
1Remove the ceiling tile.
2Place the mounting bracket in the center
of the ceiling tile. Mark the three positions
of the screw holes and a 10mm hole for
the Ethernet cable to feed through. Drill
three 4mm holes and a 10mm hole for the
Ethernet cable.
X3
3Secure the mounting bracket to the ceiling
tile using three M3x30 pan-head screws,
washers and wing nuts.
Washers
(Qty.3)
M3×30 Pan-head Screws
(Qty.3)
Wing Nuts
(Qty.3)
Hole for Ethernet cable
4
English
4Attach the EAP to the mounting bracket
by aligning ARROW 1 (on the EAP) with
ARROW 2 (on the mounting bracket), then
rotate the EAP clockwise until it locks into
place.
5Feed the Ethernet cable through the hole and
set the ceiling tile back into place. Connect
the Ethernet cable to the ETHERNET port.
■Option3：
Wall Mounting
Follow the steps below to install the EAP with the provided accessories:
1Attach the EAP to the mounting bracket by
aligning ARROW 1 (on the EAP) with ARROW
2 (on the mounting bracket), then rotate the
EAP clockwise until it locks into place.
2Make two small pencil marks on the wall. Make
sure the two marks are level and should be
98.6mm apart. Drill two 6mm holes through
the center of your marks.
98.6mm
M3×28 Plastic Wall Anchors
(Qty.4)
M3×20 Self-tapping Screws
(Qty.4)
5
English
3Insert the plastic wall anchors into the 6mm
holes and drive the self-tapping screws into
the anchors. Do not drive the screws all the
way in and leave enough clearance to hang
the EAP.
4Hang the EAP on the screws. Make sure the
EAP is firmly seated against the wall.
5Connect the Ethernet cable to the ETHERNET
port on the EAP.
6
English
Power Supply
■Power via PSE Device or Power Adapter
If the product is provided with a power adapter, power the device via a PSE device
(such as a PoE switch) or the power adapter.
Via PoE Switch
ON/OFF
1
2
Via Power Adapter
ON/OFF
1
2
■Power via POE Adapter
If the product is provided with a POE adapter, power the device via the POE
adapter.
1
3
PoE LAN
2
PoE Switch
PoE Adapter
(Up to 100m)
Switch
7
Български
Забележка: Изображението може да се различава от реалния продукт.
Мрежова топология
Типична мрежова топология за EAP (точки за достъп с протокол за
разширена автентификация) е показана по-долу.
EAP Controller
Необходим е един DHCP сървър (в типичния случай - рутер) за задаване
на IP адреси на EAP устройствата и клиентите във вашата локална мрежа.
Един компютър, на който върви софтуера EAP Controller, който може да
бъде в същата или различна подмрежа с EAP устройствата, се използва за
централно управление на EAP устройствата.
Можете да получите софтуера EAP Controller от нашия уебсайт
http://www.tp-link.com.
Инсталация на хардуера
■Опция 1: Монтаж на релса на тавана
Следвайте стъпките, описани по-долу, за да инсталирате EAP с доставените
в комплекта аксесоари:
1Позиционирайте стягата за релса на тавана
и натиснете движещата се част към основата
на релсата.
Стяга за Т-образна
релса на тавана
M3×6 винтове с глава тип звезда
(5 бр.)
Контролер
хост
Рутер Суич
Интернет
Клиенти
EAP
EAP
EAP
8
Български
2Използвайте един M3×6 винт звезда, за да
закрепите стягата към релсата на тавана.
3Закрепете монтажната скоба към стягата на
релсата на тавана с четири M3x6 винтове с
глава тип звезда.
4Закрепете EAP към монтажната скоба,
като подравните СТРЕЛКА 1 (на EAP) със
СТРЕЛКА 2 (на монтажната скоба), след
това завъртете EAP устройството в посока
на часовниковата стрелка, докато щракне на
място.
5Свържете Ethernet кабел към ETHERNET
порта.
Indice
Lingue:
Altri manuali TP-Link Router di rete
TP-Link
TP-Link ER707-M2 Manuale utente
TP-Link
TP-Link TD-8840 Manuale utente
TP-Link
TP-Link TD-W8961ND Manuale utente
TP-Link
TP-Link TL-WR850N Manuale utente
TP-Link
TP-Link Archer VR200v Manuale utente
TP-Link
TP-Link SafeStream TL-ER6120 Manuale utente
TP-Link
TP-Link TD-8817 Manuale utente
TP-Link
TP-Link Archer AX3000 Manuale utente
TP-Link
TP-Link Archer A9 Manuale utente
TP-Link
TP-Link TL-WR702N Manuale utente
TP-Link
TP-Link Archer VR400 Manuale utente
TP-Link
TP-Link WR841HPV5 Manuale utente
TP-Link
TP-Link MR5-WR542G Manuale utente
TP-Link
TP-Link SafeStream TL-R480T+ Manuale utente
TP-Link
TP-Link Archer C8 Manuale utente
TP-Link
TP-Link Archer AX95 Manuale utente
TP-Link
TP-Link Archer D7 Manuale utente
TP-Link
TP-Link TD-W8961NB Manuale utente
TP-Link
TP-Link SafeStream TL-R600VPN Manuale utente
TP-Link
TP-Link Deco W4500 Manuale utente
