TP-Link Auranet EAP120 Manuale utente

Installation Guide

Wireless N Gigabit Access Point

EAP120 / EAP220

CONTENTS

About This Installation Guide

This guide is designed to familiarize you with the general layout of the EAP,

describe how to deploy the device in your network and how to configure the

device. Your EAP has more features and functionalities which can be found in the

User Guide.

Network Topology Requirements —————————————— 01

Overview ————————————————————————— 02

Hardware Installation ——————————————————— 04

1. Installation Requirements ....................................................... 04

2. Mounting Bracket ................................................................... 04

3. Installation ............................................................................ 05

4. Powering Mode ...................................................................... 09

Getting Started with the EAP———————————————— 11

Q&A ——————————————————————————— 14

Specications ——————————————————————— 15

Technical Support ————————————————————— 16

Network Topology Requirements

Typical topology for the EAP is described below.

Router

Internet

Switch

Master EAP Slave EAPSlave EAP

Enwuvgt

Typical Topology

The EAP120 and EAP220 provide two management modes: Cluster and Standalone.

By default，

the management mode is Cluster. In this mode, all the EAPs in the

same LAN will form a Cluster, and a Master EAP will be elected among them to

manage the other EAPs, called Slave EAPs.

A DHCP server is required in the local network to assign IP addresses to the EAPs.

A router usually acts as the DHCP server.

Typically, a PoE switch can be used to provide Power over Ethernet for each EAP.

Or, each EAP must be powered with a power adapter individually.

Overview

■LED Explanation

System LED

Top View of the EAP

LED Status Indication

Quickly flashing green System initialization is complete.

Solid green The device is working properly.

Slowly flashing red The system is abnormal. RAM, Flash, Ethernet,

WLAN or firmware may be malfunctioning.

Quickly flashing yellow Firmware is being updated.

Alternating red/green/yellow twice The device is being reset.

■Interface Panel

RESET CONSOLE ETHERNET ON/OFF POWER

ARROW 1

Interface Panel of the EAP

The interface panel components of the EAP, from left to right, are described in the

following list:

Kensington Security Slot

Secure the lock into the slot to prevent the device from being stolen.

RESET

With the device powered on, press and hold the RESET button for about 8 seconds,

and then release the button. The device will restore to factory default settings.

CONSOLE

This port is used to connect with the serial port of a computer or a terminal to

check and monitor simple system information of the device.

ETHERNET

This port is for connection to a router or switch to transmit and receive data as well

as to a PSE device for power supply. Power sourcing equipment (PSE) is a device

such as a switch that provides power over Ethernet cables to linked devices.

ON/OFF

Press this button to power on/off the device. Please remember to press it to use

the device.

POWER

The power jack is for connection to the power adapter. Please use the power

adapter provided. Refer to Powering Mode to learn how to power the device via

PoE and power adapter.

ARROW 1

To align with ARROW 2 in the mounting bracket before the EAP locks into place.

Please refer to Mounting Bracket to locate ARROW 2.

Hardware Installation

The EAP can be wall or ceiling mounted and can be powered via a PSE device

or the provided adapter. Please suitably arrange your wire layout before the

mounting.

1. Installation Requirements

Check and prepare the following items in the package for installation.

One EAP

One Mounting Bracket

One Installation Guide

Three Nuts/ Washers/ Plastic Extending Tubes/ Self-tapping Screws/ Pan Head Screws

Besides the above installation kits, these tools may be needed for hardware

installation: pencil, ruler, drill, hammer, screwdriver and ladder.

2. Mounting Bracket

The following figure describes the structure of the mounting bracket.

Locking clip

ARROW 2, to align with

ARROW 1 under the

interface panel

Ceiling mounting slot

Wall mounting slot

Mounting Bracket

3. Installation

■Ceiling Mounting

Note:

■Make sure the thickness of the ceiling is less than 18mm and

the ceiling can bear at least five kilograms.

■If the ceiling is made of low-strength material like gypsum, it is

not recommended to mount the EAP on the ceiling. If it has to

do, add a layer of strong material under the nut to ensure the

EAP is mounted solidly.

1. Remove the ceiling tile.

Remove the Ceiling Tile

2. Place the mounting bracket at the center of the ceiling tile. Mark the positions

of three mounting slots and the hole for Ethernet cable to feed through.

L≈40mm

Mark of the Hole for Ethernet

cable to feed through

Mark the Positions

3. Use a drill bit to drill three holes for screws, and drill a 10mm hole for the

Ethernet cable to feed through.

10mm hole for Ethernet cable feed

4mm hole for mounting bracket

Drill the Holes

4. Secure the mounting bracket to the ceiling board with nuts, washers and pan

head screws as shown below.

Hole to feed the Ethernet cable

Hole to feed the screw

Pan head screw

Nut

Washer

Secure the Mounting Bracket

5. Align ARROW 1 with ARROW 2 as shown below, then press the EAP into the

mounting bracket.

RESET CONSOLE ETHERNET ON/OFF POWER

Align Two Arrows

6. Turn the EAP clockwise until it locks into place.

Make the EAP Lock into Place

Altri manuali per Auranet EAP120

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali TP-Link Punto di accesso wireless

TP-Link

TP-Link TL-WA701ND Manuale utente

TP-Link

TP-Link TL-WA1801 Manuale utente

TP-Link

TP-Link AP200 Manuale utente

TP-Link

TP-Link Auranet EAP110 Manuale utente

TP-Link

TP-Link Omada Pro Manuale utente

TP-Link

TP-Link Auranet EAP120 Manuale utente

TP-Link

TP-Link TL-WA901ND Manuale utente

TP-Link

TP-Link Auranet EAP110 Manuale utente

TP-Link

TP-Link TL-WA801ND Manuale utente

TP-Link

TP-Link TL-WA901ND Manuale utente

TP-Link

TP-Link Auranet EAP110 Manuale utente

TP-Link

TP-Link Auranet EAP115 Manuale utente

TP-Link

TP-Link TL-WA701ND Manuale utente

TP-Link

TP-Link Omada EAP245 Manuale utente

TP-Link

TP-Link Omada EAP660 HD V1 Manuale utente

TP-Link

TP-Link Auranet EAP110 Manuale utente

TP-Link

TP-Link Omada EAP225 Manuale utente

TP-Link

TP-Link TL-WA701ND Manuale utente

TP-Link

TP-Link Deco Manuale utente

TP-Link

TP-Link TL-WA7510N Manuale utente

TP-Link

TP-Link TL-WA7210N Manuale utente

TP-Link

TP-Link TL-WA801N Manuale utente

TP-Link

TP-Link Omada EAP115-Wall Manuale utente

TP-Link

TP-Link TL-WA801ND Manuale

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

Draytek

Draytek VIGORAP 902 Manuale utente