Travis Industries GS2/MV Manuale utente
GS2/MV Basic Wall Mount Remote Installation
with AC Adapter
SKU# 99300696
Page 1 of 18 17602250 - 10/7/22 Travis Industries, Inc.
Compatibility
Radiant Large GSB2 & MV
Radiant Medium GSB2 & MV
Radiant Small GSB2 & MV
42 PB Linear GSB2 & MV
54 PB Linear GSB2 & MV
72 PB Linear GSB2 & MV
Northfield MV
Berkshire MV
Greenfield MV
36 PB CF GSB2 & MV
42 PB CF GSB2 & MV
Packing List
Remote Transmitter
Remote Receiver/Battery Box
(4) AA batteries & (3) AAA batteries
(1) AC Adapter
(1) Power Harness Adapter (with additional
Molex connector plug)
(1) Power Cord
(1) Receiver Adapter Harness (comes attached
to receiver)
(1) Strain Relief
(2) Strain Relief Brackets (Insert and Stove)
(1) 8-32 nut
(1) ¼” drive screw
(2) zip-ties
(1) Switch Blank
GS2/MV Basic Wall Mount Remote Installation
with AC Adapter
SKU# 99300696
Page 2 of 18 17602250 - 10/7/22 Travis Industries, Inc.
Warnings
The transmitter and receiver are radio frequency devices. Placing the transmitter in or near metal may
severely reduce the signal range.
Turn off power to the heater during installation or maintenance (unplug or turn off at the breaker).
Turn off the main gas supply to the appliance during appliance installation or maintenance.
REMOTE CONTROL / PILOT WARNING: Installing batteries in the battery holder or connecting the
appliance to power may automatically initiate the CPI pilot mode, resulting in a lit pilot flame. Do not
place combustibles inside the firebox.
If using the option blower, ember-glo lights or under lighting, install them first.
The optional accessories should be installed before installing the remote.
Table of Contents
Compatibility .............................................................................................................................................................. 1
Packing List ............................................................................................................................................................... 1
Warnings.................................................................................................................................................................... 2
Table of Contents ...................................................................................................................................................... 2
Overview.................................................................................................................................................................... 3
General Fireplace, Insert, and Radiant Stove Installation Instructions ..................................................................... 3
Steps Specific to MV Fireplace and Insert Installation .............................................................................................. 7
Steps Specific to MV Stove Installation..................................................................................................................... 8
Steps Specific to GSB2 Installation ........................................................................................................................... 9
Wiring Diagram MV.................................................................................................................................................. 10
Wiring Diagram GSB2 ............................................................................................................................................. 11
Operating Instructions ............................................................................................................................................. 12
Direct Fireplace Operation....................................................................................................................................... 13
Remote Operation ................................................................................................................................................... 14
Low Battery Indicator ............................................................................................................................................... 16
Display Fahrenheit or Celsius.................................................................................................................................. 16
Power Outages ........................................................................................................................................................ 17
Child-Proof Feature ................................................................................................................................................. 17
How to Turn the Thermostat Feature On and Off.................................................................................................... 17
Disabling Modes From the Remote ......................................................................................................................... 18
GS2/MV Basic Wall Mount Remote Installation
with AC Adapter
SKU# 99300696
Page 3 of 18 17602250 - 10/7/22 Travis Industries, Inc.
Overview
This kit supplies a basic wall-mount remote kit with an AC adapter to power the remote receiver. The basic
installation is the same for MV and GSB stoves and inserts. This kit can also be used with MV and GSB
fireplaces however, the way the kit connects to AC power is slightly different than with the inserts and stoves (see
fireplace installation section for details).
General Fireplace, Insert, and Radiant Stove Installation Instructions
This set of installation instructions shows a summary of the remote installation.
For detailed instructions on the placement of the receiver and other details, refer to the installation
manual included with your appliance.
RADIANT INSERT NOTE: If a blower is used you will not
use the strain-relief bracket that is included with this kit and
can skip step one. When a blower is used, the ground for the
remote AC adapter will connect to the blower rheostat
housing and the blower ground wire will be attached to the
extra tab on the AC adapter grounding quick connect.
GS2/MV Basic Wall Mount Remote Installation
with AC Adapter
SKU# 99300696
Page 4 of 18 17602250 - 10/7/22 Travis Industries, Inc.
RADIANT STOVE NOTE: If a blower is being uesd, install the blower kit first and discard the power cord and strain
relief bracket from this kit. With the blower kit installed follow the steps below to electricly ground the accessories to
the appliance belly pan.
a. Disconnect the blower ground from the strain relief bracket
b. Install the AC adapter ground to the strain relief bracket where you just removed the blower ground.
c. Reinstall the blower
g
round on the extra
g
round tab attached to the remote reciever
g
round quick reliease.
1. Install the new strain-relief bracket (stoves
and inserts).
For stoves, the strain relief bracket can be installed anywhere on the belly pan of the appliance that is out of the
way of other components (see suggestions to the right). Insert the stud on the bracket through an available hole
in the belly pan. Secure the bracket with the included 8-32 nut.
With inserts, the bracket installs on the front of the right wall
of the gas control area below the firebox. Use the included
screw to secure the bracket. Use the included screw to
secure the bracket to one of the two existing holes in the
side of the insert (as shown to the right).
GS2/MV Basic Wall Mount Remote Installation
with AC Adapter
SKU# 99300696
Page 5 of 18 17602250 - 10/7/22 Travis Industries, Inc.
2. Install the power cord with a strain relief clamp into
the bracket. Feed the Molex end of the power cord
through the hole in the bracket. Close to the end of
the wire insulation place the strain relief on the wire
with the sloped end facing the plug end of the cord.
Bend the attached plug portion of the strain relief
over until it is in line with the slot in the strain relief.
Pinch the two portions of the strain relief together
with pliers and insert the sloped end of the strain
relief into the hole in the bracket until the strain relief
snaps into place.
3. STOVES & INSERTS Attach
the power harness adapter to
the power cord. Attach the
ground wire to the grounding
tab on the power cord bracket
on stoves and inserts.
FIREPLACES Disconnect the main
power harness from the junction
box inside the fireplace. Install the
power harness adapter on the
junction box where you just
disconnect the main power
harness. Plug the main power
harness into the Molex that is
attached to the adapter. Bunch the
ground wire up and use one of the
included zip ties to secure the
ground.
NOTE: If no other accessories are going to be installed on the appliance, use the female Molex connector
to ensure that the electrical connections on the unused power Molex don’t contact the appliance
and short out.
If using a blower and/or Ember-Glo/Under Lights, use this Molex to supply power for those
accessories.
GS2/MV Basic Wall Mount Remote Installation
with AC Adapter
SKU# 99300696
Page 6 of 18 17602250 - 10/7/22 Travis Industries, Inc.
4. Connect the green and white wires to the corresponding On/Off switch wires.
5. Connect the blue and white wires from the back of the receiver to the AC adapter. The insulation that
covers the quick connects on the AC adapter are different colors. The blue connector should be attached
to the blue wire from the receiver and the clear connector should be attached to the white wire.
Orientation DOES matter.
6. Plug the AC adapter into the pigtail outlet on the power harness adapter.
GS2/MV Basic Wall Mount Remote Installation
with AC Adapter
SKU# 99300696
Page 7 of 18 17602250 - 10/7/22 Travis Industries, Inc.
Steps Specific to MV Fireplace and Insert Installation
This set of installation instructions shows a summary of the remote installation.
For detailed instructions on the placement of the receiver and other details, refer to the
installation manual included with your appliance.
1. Remove the Brown and Red wires from the back of the on/off switch.
2. Place the remote receiver in the appliance (see appliance manual for placement details). Connect the
Brown and Red wires to the Green and White wires from the receiver (polarity does not matter in this
application).
NOTE: The Molex connector with the Red and White wires remains empty in this application.
3. Remove the on/off switch from its mounting location. Place the switch blank into this location.
4. Verify the wiring does not contact any hot or moving components. Restore the appliance to the correct
configuration. Install the batteries in the remote and receiver. Synchronize the remote to the receiver
(page 13).
Squeeze tabs in to remove switch
GS2/MV Basic Wall Mount Remote Installation
with AC Adapter
SKU# 99300696
Page 8 of 18 17602250 - 10/7/22 Travis Industries, Inc.
Steps Specific to MV Stove Installation
This set of installation instructions shows a summary of the remote installation.
For detailed instructions on the placement of the receiver and other details, refer to the
installation manual included with your appliance.
1 Locate the Green and White wires labeled “REMOTE” near the gas control valve. Connect the Green and
White wires from the back of the remote to the “REMOTE” wires found in step 1.
2 Remove clear plastic film from the Velcro strips on the bottom of the heatshield for the receiver. Turn the
assembly over so the strips are facing downward. Gently push the wires back into the appliance as you move
the receiver assembly into place. Adhere the assembly to the floor of the controls area of the stove. Make
sure the placement does not obstruct the movement of the door.
3 Verify the wiring does not contact any hot or moving components. Restore the appliance to the correct
configuration. Install the batteries in the remote and receiver. Synchronize the remote to the receiver (page
13).
GS2/MV Basic Wall Mount Remote Installation
with AC Adapter
SKU# 99300696
Page 9 of 18 17602250 - 10/7/22 Travis Industries, Inc.
Steps Specific to GSB2 Installation
This set of installation instructions shows a summary of the remote installation.
For detailed instructions on the placement of the receiver and other details, refer to the
installation manual included with your appliance.
1 Remove the Green and White wires from the back of the on/off switch.
2 Connect the Green and White wires to the Green and White wires on the remote receiver (Green must attach
to Green and White to White).
3 Disconnect the Molex connector that attaches to the battery holder (discard the battery holder)
4 Connect the Molex connector to the connector from the remote receiver.
5. Verify the wiring does not contact any hot or moving components. Restore the appliance to the correct
configuration. Install the batteries in the remote and receiver. Synchronize the remote to the receiver (page 13).
Stock Confi
g
uration
Green to Green
White to White
Discard
GS2/MV Basic Wall Mount Remote Installation
with AC Adapter
SKU# 99300696
Page 10 of 18 17602250 - 10/7/22 Travis Industries, Inc.
Wiring Diagram MV
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Travis Industries Telecomando
Travis Industries
Travis Industries GreenSmart 2 Manuale
Travis Industries
Travis Industries Cypress GS2 Manuale utente
Travis Industries
Travis Industries 3003 Manuale utente
Travis Industries
Travis Industries GreenSmart SKU 99300699 (NG) Manuale utente
Travis Industries
Travis Industries 99300661 Manuale utente
