TRENDnet TEG-S081FMi Manuale utente

TEG-S081FMi

Quick Installation Guide

Table of Contents

English ......................................................................................................

Troubleshooting ........................................................................................

1. Before You Start

2. Hardware Installation ........................................................................

3. Configure the Switch .........................................................................

................................................................................

Table of Contents

Version 12.19.2007

System Requirements

Application

Package Contents

1. Before You Start

English

?User Guide CD-ROM

?Quick Installation Guide

?2 Mounting Brackets with Screws

?RS-232 cable

?AC Power Cord

TEG-S081FMi

Web Browser: Internet Explorer (6.0 or above)

Computer with Serial port

Computer with Fiber connection or a Media Converter (e.g. TFC-210MSC,

TFC-2000MSC, TFC-2000S20)

50/125 or 62.5/125 µm Multimode Fiber cable with SC-type connectors for

100BaseFX ports

Multimode or Single-mode Fiber cables with LC-type connectors for

Mini-GBIC modules (optional)

Mini-GBIC module (e.g. TEG-MGBSX, TEG-MGBS10, TEG-MGBS40,

TEG-MGBS80, TEG-MGBS10D3_D5, TEG-MGBS40D3_D5) for

Mini-GBIC slots

16-Port 10/100/1000Mbps Gigabit

Web Smart Switch with Mini-GBIC Slots

(TEG-160WS)

8-Port 100base-FX SNMP Layer 2 Managed Switch

(TEG-S081FMi)

Multi-Mode Fiber

Mini-GBIC Modules

(TEG-MGBSX)

Workstations with Gigabit Adapters

(TEG-PCBUSR)

Console Connection

(RS-232)

Media Convertor

RS-232

Workstation with Gigabit Adapter

(TEG-PCBUSR)

1000MbpsFiber 10/100Mbps

2. Hardware Installation

English

1. Connect the Power Cord to the

rear of the TEG-S081FMi and then

to a power outlet. Then press on

the power switch to turn the switch

on.

Note: After hardware installation is complete, use the Web-based Smart Utility

to configure the TEG-S081FMi. To access the Web-based Smart Utility, open

your web browser, and enter the default IP Address http://192.168.16.1 and

default password "admin". Make sure your computer and the TEG-S081FMi

are configured to the same network segment.

English

2. Slide a TRENDnet mini-GBIC

module into the mini-GBIC slot

(optional).

3. Connect a Fiber cable to one of the

ports on the switch and to a fiber

connection on your network.

Note:

1. TRENDnet mini-GBIC modules

have LC-type fiber connectors.

If your fiber Gigabit connection

is SC-Type, you need a LC to

SC fiber connector.

2. TRENDnet mini-GBIC modules

are straight Gigabit. Your fiber

connection must be Gigabit

when connecting to a mini-GBIC

module.

English

Note: Before the Switch can be configured, a Static IP address must be

assigned on your computer's network adapter in the subnet of 192.168.16.x.

Since the Switch's default IP address is 192.168.16.1, make sure no other

network devices are assigned an IP address of 192.168.16.1. (Refer to

Troubleshooting section on how to configure TCP/IP settings on your PC.)

3. Configure the Switch

Browser Configuration

2. Enter the User name and

Password, and then click OK.

By default:

User Name: root

Password: root

1. Open your web browser, type

http://192.168.16.1 in the Address

bar, and then press Enter.

3. Click Administrator > IP

Address. Then change the IP

Address to be in the same subnet

as your Network. Enter the

Subnet Mask and Gateway to

match your network. Then click

Apply.

English

2. Go to Start > Programs >

Accessories > Communications >

HperTerminal

Hyper Terminal

3. Enter a name, choose an icon and

then click OK.

4. Select the correct COM port (e.g.

COM1, COM2) and then click OK.

1. Connect the RS-232 cable from a

serial port on your Windows PC to

the console port on your computer.

English

6. Press Enter.

5. Enter the following, click Apply

and then click OK:

Bits per second: 9600

Data bits: 8

Parity: None

Stop bits: 1

Flow control: None

7. Type in the user name and

password and then press Enter.

By default, the user name and

password is root.

8. Press Tab to navigate to Switch

Static Configuration and then

press Enter.

English

9. Press Tab to navigate to

Administration Configuration

and then press Enter.

10. Use tab to navigate to Edit then

hit enter. Change the IP Address

to be in the same subnet as your

Network. Enter the Subnet Mask

and Gateway to match your

network. Press the down arrow,

press tab to navigate towards

Save and then press Enter. Then

press any key to return to the

previous screen.

To ensure the highest level of customer service and support, please take a moment to

Thank you for choosing TRENDnet

Troubleshooting

Q1:

A1:

After connecting the TEG-S081FMi to a power outlet, the LEDs do not turn on.

Check the connection of the power cord to the TEG-S081FMi and the power outlet. Also

check that the power outlet is receiving power.

Q3:

A3:

I connect the switch to my network, but I am unable to make a connection

First, verify that you are using the proper fiber cable. Second, verify that the TX and RX

cables have been reverse on the opposite Fiber connection. Third, when connecting to the

mini-GBIC modules, your Fiber connection must be Gigabit. Fourth, power down the

switch. Wait 15 seconds, then plug the switch back in.

Q4:

A4:

I changed the IP address of the switch, but I forgot it. How do I reset my TEG-S081FMi?

Follow the instructions below:

1) Connect the RS-232 cable from a serial port on your Windows PC to the console

port on your computer.

2) Go to Start > Programs > Accessories > Communications > Hyperterminal

3) Enter a name, select an icon and then click OK.

4) Select the correct COM port (e.g. COM1, COM2) and then click OK.

5) Enter the following, click Apply and then click OK:

Bits per second: 9600

Data bits: 8

Parity: None

Stop bits: 1

Flow control: None

6) Press Enter.

7) Enter the user name and password. By default, the user name and password is root.

8) Press Tab to navigate to Reboot Switch and then press Enter.

9) Press Tab to navigate to Default and then press Enter.

10)Press yto continue.

The default IP address of the switch is 192.168.16.1.

If you still encounter problems or have any questions regarding the TEG-S081FMi, please

contact TRENDnet’s Technical Support Department.

Q2: How do I configure TCP/IP settings on my computer?

1. Go into the Control Panel and double-click the Network

Connections icon, right-click the Local Area

Connection icon and then click Properties.

2. Click Internet Protocol (TCP/IP) and then click

Properties. Then click on Use the following IP

address, and make sure you assign your network

adapter an IP address in the subnet of 192.168.16.x.

Altri manuali per TEG-S081FMi

Indice

Altri manuali TRENDnet Interruttore

TRENDnet

TRENDnet TK-423K Manuale utente

TRENDnet

TRENDnet TL2-G244 Manuale utente

TRENDnet

TRENDnet TK-1604R Manuale utente

TRENDnet

TRENDnet TK-205i Manuale utente

TRENDnet

TRENDnet TK-1601R Manuale utente

TRENDnet

TRENDnet TEG-S80ES Manuale utente

TRENDnet

TRENDnet TE100-DS24 Manuale utente

TRENDnet

TRENDnet TEG-S80TX Manuale utente

TRENDnet

TRENDnet TE100-S24V Manuale utente

TRENDnet

TRENDnet TEG-S4000i Manuale utente

TRENDnet

TRENDnet TPE-224WS - Web Smart PoE Switch Manuale utente

TRENDnet

TRENDnet TE100-S16plus Manuale utente

TRENDnet

TRENDnet TE100-S16R Manuale utente

TRENDnet

TRENDnet TI-PG162 Manuale utente

TRENDnet

TRENDnet TU2-400 Manuale utente

TRENDnet

TRENDnet TK-400K - DATA SHEETS Manuale utente

TRENDnet

TRENDnet TEG-S081Fi Manuale utente

TRENDnet

TRENDnet TU-400E Manuale utente

TRENDnet

TRENDnet TE100S8P - Fast Ethernet Switch Manuale utente

TRENDnet

TRENDnet TK-423K - USB/PS/2 KVM Switch Manuale utente

TRENDnet

TRENDnet TEG-S2600I - 10/100Mbps Switch With Mini-GBIC... Manuale utente

TRENDnet

TRENDnet TEG-S2620is Manuale utente

TRENDnet

TRENDnet Web Smart Switch Series Manuale utente

TRENDnet

TRENDnet TE-1710 Manuale utente

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente