TriBrer AFI430 Manuale utente
WARNINGWARNING
You arecautioned that changesor modifications not espressly approved in
this document could voidyout authority to operatethis equipment.
To reducethe risk of fireor electric shock,do notexpose this apparatus to
rain or moisture.
Toavoid electrical shock, do not openthe cabinet. Refer servicing to quali-
fied personnel only.
NOTENOTE
As the laser isharmful to the eyes,do not attempt todisassemble the cabinet.
Avoiding condensation problems
As much aspossible, avoid sudden temperature changes. Donot attempt
to use thedrive immediately after moving it froma cold to a warm location,
to raising the roomtemperature suddenly,as condensation may formwith
in the drive.If the temperature changes suddenly whileusing the drive,
stop using itand take out batteries for atleast an hour.
Storage
When long timeno use,must take out the batteriesto avoid destroying the
device.
Use batteries
At the same time, can not usedifferent style ordifferent capacitance batteries.
And only charge therechargeable batteries.
1
2
Description
1-Fiber location
2-Left indicative led
3-Power key ofvisual fault locatorand optical powermeter
4-Trigger of the fiber identifier
5-Right indicative led
6-Power indicative led
7-Calibration button
8-Connector of OPM/VFL( optional )
8
1
3
4
25
6
7
3
Battery set
Warning:At the sametime, can not usedifferent style and different capacitance batteries.
1.Push the tip 2.Open the batteryslot
3.Replace the batteries 4.Close the batteryslot
4
Silver indicative line
Availaber for different Fiber
1.Available for 800nm~1700nm laser signal
2 Based on non-destructivetechnology
3 No need toreplace the clampblock for different fiber
.
.
Availaber for different Fiber
250um bare fiber
900um fiber
2.5mm patch cord
3mm patch cord
When testing 2.5mmand 3.5mm patchcord, the silver
indicative line needto be seento ensure a correct
measurement
5
Fiber Identification models
LOWBATT
a.standard Optical Fiber
Identfier
b.Optical Fiber Identifier
with OPM mode
c.Optical Fiber Identifier
with VFL mode
AFI430 serialhas three models,include standard Optical
Fiber Identifier,Optical Fiber Identifierwith OPM modeand
Optical Fiber Identifierwith VFL mode. Different models with
different buttons, which shown inthe pictures above.
>2s SAVE
Environment Light Calibration
6
Calibration button
Push down thetrigger of thefiber identifier andhold, then
long press the button. Until thebeep be onand the
the screen shows"CAL", the environmentlight calibration is
finished.
Operation
7
Put the fiberinto the fiberlocation and pushdown the
trigger to begintesting. After1~3 seconds, itoutput the
results.
The data in the LCDmeans the signalintensity, if the
power value isover +5dBm, itwill be "HI",if the value is
less than -40dBm,it will be"LO".
Carrier frequency: 270Hz,1KHz, 2KHz andOFI.
Hz
Signal Direction
8
Right to left Left to right
It is themain function to test the direction of the signal
in the fiber. When signalis transporting inthe fiber,the
corresponding indicative led will be on.
Hz
Optical Power Meter
9
ON/OFFON/OFF
Power key Laser source wavelength
switch key
When the opticalfiber identifier hasOPM mode, press
key to turnon the device,short press key
to select thelaser source wavelength.
Open the capin the bottomof the deviceand connect the
fiber correctly, the device will calculate the power value
automatically. The screen will show thecorresponding
wavelength and powervalue.
nm
Indice
Altri manuali TriBrer Sensore di sicurezza
