Tripp Lite SmartOnline 2-9USTAND Manuale utente

Owner’s Manual

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

Important Safety Instructions 2

Installation 3

Basic Operation 6

Battery Replacement 11

Storage and Service 11

Audio/Video

Pure Sine Wave UPS Systems

• Intelligent, True On-Line Operation

• Pure Sine-Wave Output

• Zero Transfer Time

• 1000VA - 2200VA Capacities

• Extended-Run Options

Warranty Registration 12

Troubleshooting 10

Warranty

Registration:

to win a FREE Tripp Lite product—

www.tripplite.com/warranty

Not suitable for mobile applications.

200907169 93-2615.indd 1 8/11/2009 10:14:56 AM

UPS Location Warnings

• InstallyourUPSindoors,awayfromexcessmoistureorheat,conductivecontaminants,dustordirect

sunlight.

• Forbestperformance,keeptheindoortemperaturebetween32ºFand104ºF(0ºCand40ºC).

• LeaveadequatespacearoundallsidesoftheUPSforproperventilation.

• Donotmountunitwithitsfrontorrearpanelfacingdown(atanyangle).Mountinginthismannerwill

seriouslyinhibittheunit’sinternalcooling,eventuallycausingproductdamagenotcoveredunderwarranty.

UPS Connection Warnings

• ConnectyourUPSdirectlytoaproperlygroundedACpoweroutlet.DonotplugtheUPSintoitself;

thiswilldamagetheUPS.

• DonotmodifytheUPS'splug,anddonotuseanadapterthatwouldeliminatetheUPS’sgroundonnection.

• DonotuseextensioncordstoconnecttheUPStoanACoutlet.Yourwarrantywillbevoidedif

anythingotherthanTrippLitesurgesuppressorsareusedtoconnectyourUPStoanoutlet.

• IftheUPSreceivespowerfromamotor-poweredACgenerator,thegeneratormustprovideclean,

filteredoutput.

Equipment Connection Warnings

• Useofthisequipmentinlifesupportapplicationswherefailureofthisequipmentcanreasonablybe

expectedtocausethefailureofthelifesupportequipmentortosignificantlyaffectitssafetyor

effectivenessisnotrecommended.Donotusethisequipmentinthepresenceofaflammable

anestheticmixturewithair,oxygenornitrousoxide.

• DonotconnectsurgesuppressorstotheoutputofyourUPS.ThismightdamagetheUPSandwillvoidthe

surgesuppressorandUPSwarranties.However,TrippLitehasapprovedtheconnectionofextensioncords

and/orourHT3100PCPowerConditioningCenterattheoutputofthisUPSforgreateraccessibilityandto

increasethenumberofbatterybackupsupportedoutlets.*Theuseofextensioncordsisapprovedfor

remotepowerneeds,aslongastheextensioncordissizedproperly(byusingproperlygaugedwire)and

properlyconnected(byhavinga3-pronggroundedplugononeendanda3-prongreceptacleontheother

endofthiscord).TheUPSitselfmustbedirectlyconnectedtoaproperlygroundedwalloutlet.

* The total number of components connected should not exceed the UPS capacity. This will overload your UPS system.

Battery Warnings

• Batteriescanpresentariskofelectricalshockandburnfromhighshort-circuitcurrent.Observe

properprecautions.Donotdisposeofthebatteriesinafire.DonotopentheUPSorbatteries.Donot

shortorbridgethebatteryterminalswithanyobject.UnplugandturnofftheUPSbeforeperforming

batteryreplacement.Usetoolswithinsulatedhandles.Therearenouser-serviceablepartsinsidethe

UPS.Batteryreplacementshouldbeperformedonlybyauthorizedservicepersonnelusingthesame

numberandtypeofbatteries(sealedLead-Acid).Thebatteriesarerecyclable.Refertoyourlocal

codesfordisposalrequirementsorintheUSAonlycall1-800-SAV-LEADor1-800-8-BATTERY

(1-800-822-8837)orvisitwww.rbrc.comforrecyclinginformation.TrippLiteoffersacompleteline

ofUPSSystemReplacementBatteryCartridges(R.B.C.).VisitTrippLiteontheWebatwww.

tripplite.com/support/battery/index.cfmtolocatethespecificreplacementbatteryforyourUPS.

• Duringhot-swapbatteryreplacement,theUPSwillnotprovidebackuppowerintheeventofa

blackoutorotherpowerinterruptions.

• DonotoperateUPSwithoutbatteries.

• Whenaddingexternalbatterypackstoselectmodelswithexternalbatterypackconnectors,connect

onlyTrippLite-recommendedbatterypacksofthecorrectvoltageandtype.Donotconnector

disconnectbatterypackswhentheUPSisoperatingonbatterypower.

SAVE THESE INSTRUCTIONS

Thismanualcontainsinstructionsandwarningsthatshouldbefollowedduringtheinstallation,operation

andstorageofallTrippLiteUPSSystems.Failuretoheedthesewarningswillvoidyourwarranty.

Important Safety Instructions

200907169 93-2615.indd 2 8/11/2009 10:14:56 AM

Mountyourequipmentineithera4-postor2-postrackorrackenclosure.Theusermustdeterminethe

fitnessofhardwareandproceduresbeforemounting.Ifhardwareandproceduresarenotsuitableforyour

application, contact the manufacturer of your rack or rack enclosure.The procedures described in this

manualareforcommonrackandrackenclosuretypesandmaynotbeappropriateforallapplications.

4-Post Mounting

AllUPSmodelsincludehardwarerequiredtomountin

a 4-post rack. Select models include an adjustable

rackmount shelf kit to provide additional support. If

your UPS model does not include an adjustable

rackmount shelf kit, skip steps 1 and 2.

Connectthetwosegmentsofeachshelf Ausingthe

included screws and nuts B. Leave the screws

slightlyloosesothattheshelvescanbeadjustedin

thenextstep.

Adjusteachshelftofityourrack,thenmountthem

inthelowestavailablespaceofyour rackwiththe

screws,nutsandwashersprovided C.Notethatthe

support ledges should face inward. Tighten the

screwsthatconnecttheshelfsegments B.

Attachmountingears Dtothefrontmountingholes

ofyourequipment Eusingthescrewsprovided F

.Theearsshouldfaceforward.

Usinganassistantifnecessary,liftyourequipment

andslideitontothemountingshelves.Attachyour

equipment to the rack by using the appropriate

hardware Gthroughitsmountingearsandintothe

rackrails.

2-Post Mounting

IfyoumounttheUPS ina2-postrack,itrequiresthe

additionofaTrippLite2-PostRackmountInstallation

Kit (model: 2POSTRMKITWM, sold separately). See

InstallationKitowner’smanualfor2-postrackmounting

procedures.

Your UPS can be mounted in an upright tower

positionwithoptionalbasestandssoldseparatelyby

TrippLite(Model#2-9USTAND).Whenmounting

theUPSonadjustablebasestands,makesure that

thecontrolpanelistowardthetop.Thecontrolpanel

may be rotated to make it easier to read. Insert a

small screwdriver or similar tool in the slots on

eithersideofthepanel,popitout,rotateit,andpop

itbackintoplaceasshown.

WARNING!

All UPS systems are extremely heavy. Use caution

when lifting and mounting. User must properly

stabilize the UPS when lifting and mounting.

Rack Mounting

Installation

Tower Mounting

200907169 93-2615.indd 3 8/11/2009 10:14:58 AM

Important Safety Instructions

Connection and Start-Up

Plug your UPS’s line cord into an

electrical outlet.

Your UPS must be connected to a dedicated circuit of

sufficient amperage.Note,however,that theselect models

may be fitted with different plug types. Refer to the “OP

Rating/ Plug Rating” chart printed on the top of your

UPS.

Once your UPS is plugged in, the fan and all Indicator

Lights will turn ON. The “LINE” and “LOAD ACTIVE

METER”LEDswillilluminate andtheUPSwillemitabeep

toindicatenormaloperation.However,powerisnotsupplied

to yourUPS’sACoutletsuntiltheUPSisturnedon.

Plug your equipment into your UPS.

YourUPSisdesignedtosupportaudio/videosystemsand

theirassociatedservers,MediaCenterPCs,andaTrippLite

HT3100PCorHT7300PCPowerConditioningCenteronly.

The total number of components connected should not

exceedUPScapacity.ThiswilloverloadyourUPSsystem.

YouwillalsooverloadyourUPSifyouconnecthousehold

appliancestotheUPS'soutlets.

Turn your UPS ON:

• Pressthe“ON/TEST”Button

• Holditforseveralsecondsuntilyouhearabeep

• Releaseit

Your UPS will begin providing AC power to its outlets. The “ON LINE” LED

will illuminate.

Note: The UPS system will function properly upon initial startup, however,

maximum runtime for the unit’s battery will only be accessible after it has

been charged for 24 hours.

YourUPSwillfunctionproperlywithoutthese

connections.

Phone/Network Line Surge

Suppression (Select Models)

TheseRJ-45jacksprotectconnectedequipmentfrom

surges

onaphoneornetworkline.*Usingappropriatenetwork

cords,connectyourwalljacktotheUPSjackmarkedIN

andyourequipmenttotheUPSjackmarkedOUT.Make

surethattheequipmentyouconnecttotheRJ-45jacksis

alsoprotectedontheACpowerline.

* Not compatible with PoE (Power Over Ethernet) applications.

CAUTION

Risk of electric shock

See top of unit for cautionary markings

WARNING

CONNECT 48 VDC

BATTERY SYSTEMS ONLY

CONNECTING OTHER

SYSTEMS WILL VOID

WARRANTY

30A

Your model may differ.

Installation (continued)

Optional Connections

CAUTION

Risk of electric shock

See top of unit for cautionarymarkings

WA RNING

CONNECT 48 VDC

BATTERY SYSTEMSONL Y

CONNECTING OTHER

SYSTEMS WILL VOID

WARRANTY

30A

200907169 93-2615.indd 4 8/11/2009 10:14:59 AM

Optional Connections (continued)

USB and RS-232 Serial

Communications

Usethe includedUSBcable (see 2a )and/or DB9

serialcable(see 2b )toconnecttheUPStoaMedia

Center PC, home automation system or server.

InstalltheTrippLitePowerAlertSoftwareappropriate

to your equipment's operating system. Your UPS

mayfeaturetwocommunicationports;theadditional

port can be used to connect the UPS to a second

homeentertainmentorhomeautomationPCthathas

PowerAlertSoftwareinstalled.Formoreinformation,

consultyourPowerAlertsmanual.

EPO Port Connection

(Select Models)

This optional feature is only for those applications

thatrequireconnectiontoahomeautomation/home

securityEmergencyPowerOff(EPO)circuit.When

the UPS is connected to this circuit, it enables

emergency shutdown of the UPS's inverter. Using

the cable provided, connect the EPO port of your

UPS(see 3a )toauser-suppliednormallyclosedor

normally open switch according to the circuit

diagram (see 3b ). The EPO port is not a phone

line surge suppressor; do not connect a phone line

to this port.

External Battery Connection

Check to ensure that the external batteries you are

connecting match the voltage listed on your UPS's

battery connector. All UPS models come with a

robust internal battery system; all models feature

connectors that accept optional external battery

packs (sold separately from Tripp Lite) to provide

additional runtime. Adding external batteries will

increase recharge time as well as runtime. See the

batterypackowner'smanualforcompleteinstallation

instructions.Makesurecablesarefullyinsertedinto

their connectors. Small sparks may result during

batteryconnection;thisisnormal.Donotconnector

disconnect battery packs when the UPS is running

onbatterypower.

CAUTION

Risk of electric shock

See top of unit for cautionary markings

WARNING

CONNECT 48 VDC

BATTERY SYSTEMS ONLY

CONNECTING OTHER

SYSTEMS WILL VOID

WARRANTY

30A

48V/26A

Your model may differ.

Installation (continued)

CAUTION

Risk of electric shock

See top of unit for cautionary markings

WARNING

CONNECT 48 VDC

BATTERY SYSTEMS ONLY

CONNECTING OTHER

SYSTEMS WILL VOID

WARRANTY

30A

2a Your model may differ.

CAUTION

Risk of electric shock

See top of unit for cautionary markings

WARNING

CONNECT 48 VDC

BATTERY SYSTEMS ONLY

CONNECTING OTHER

SYSTEMS WILL VOID

WARRANTY

30A

3a Your model may differ.

4-5

200907169 93-2615.indd 5 8/11/2009 10:15:01 AM

Front Panel Switches

“ON/TEST” Button:ThisswitchcontrolsfourseparateUPSfunctions:

UPS Power ON

ToturntheUPSon,pressthisbutton,holditforseveralsecondsuntilyouhear

abeep,thenreleaseit.The“ONLINE”LEDwillilluminate.

UPS Self-Test

Duringnormalon-lineoperation,pressthisbuttonandholdituntilyouheara

beep.Thisinitiatesa10-secondself-testofthebattery.TheUPSwillshiftto

batterypower(allLEDswillilluminate)fortenseconds.

Alarm Silence

TosilencetheUPS“on-battery”alarm,pressthisbuttonandholdituntilyou

hearabeep.

UPS Cold Start

TouseyourUPSasastand-alonepowersourcewhenACpowerisunavailable

(i.e.duringablackout),pressthisbuttonandholdituntilyouhearabeep.The

UPSwillthenprovidebatterypowertoitsoutlets.*

* The “ON BATT” Indicator Light will be illuminated since your UPS will be operating from battery

power.

“OFF” Button:ThisbuttonturnspowerOFFattheUPSreceptacles.Press

this switch, hold it until you hear a beep, then release it. The UPS will

continuechargingandthefanwillcontinuetocoolinternalcomponentseven

after you turn the UPS receptacles off. To turn the UPS OFF completely,

including the charger, disconnect the UPS’s power cord after pressing the

“OFF”switch.

“ON LINE” LED:Thisgreenlightwillilluminateconstantlytoindicatethe

UPS is performing normal on-line operation (filtering and resynthesizing

incomingAClinevoltagetoprovidepuresinewaveoutput).Whenthislight

is illuminated, you can monitor the load level of your UPS on the “LOAD

ACTIVEMETER”LEDs.

“LINE” LED: This green light will illuminate constantly to indicate the

utilitysuppliedAClinevoltageatyourwalloutletisnominal.Itwillflashif

thelinevoltageisoutsidethenominalrange(eithertoolowortwohigh).No

actionisrequiredonyourpartwhentheLEDflashes;theUPScontinuously

andautomaticallyfiltersAClinepowertoprovideyourequipmentwithpure

sinewaveACpower,regardlessofbrownoutorovervoltageconditions.Ifthis

lightisoff,thenAClinevoltageisnotpresent(blackout)orisatanextremely

highvoltage,andtheUPSwillprovideconnectedequipmentwithpowerfrom

battery.

Front Panel Indicator Lights

Basic Operation

200907169 93-2615.indd 6 8/11/2009 10:15:01 AM

Front Panel Indicator Lights continued

“BYPASS” LED:ThisyellowlightwillflashtoindicatethattheUPS’sDC/

AC inverter is deactivated and the UPS is in the “Bypass” mode. During

normaloperationthisLEDwilllightbrieflywhentheunitispluggedin,butif

aninternalfaultoroverloadoccursthislightwillflashconstantlytoshowthat

connectedequipmentwillreceivefilteredACmainspower,butwillnotreceive

batterypowerduringablackout.Inthiscase,contactTrippLiteforservice.

“FAULT” LED (select models only):ThisredlightwillflashwhenyourUPS

detectsaninternalfault(overheating,overvoltages,etc.)orwhenitdetectsa

wiringfaultin yourwalloutlet (reversedphases,missing ground,etc.) The

UPSwillonlydetectwiringfaultswhenitispluggedintoautilityoutletbut

not turned ON. If the light persists after restarting the UPS, contact an

electriciantochecktheACline.YourUPSwillidentifythepresenceofmost

(butnotall)wiringfaults.

“LOAD ACTIVE METER” LED:Thisgreenlightwillilluminatewhenyour

UPSisreceivingACpowertoindicatethatthesetoffourdual-functionLEDs

isdisplayingtheloadlevelofyourUPS.

“BATT ACTIVE METER” LED:Thisgreenlightwillilluminatewhenyour

UPS is operating from battery power to indicate that the set of four dual-

functionLEDsisdisplayingthebatterychargelevelofyourUPS.Note:the

“ONBATT”LEDwillalsobeilluminated.

“OVERLOAD” LED:Thisredlightwillilluminateconstantlytoindicatethat

yourUPS’scapacityhasbeenexceededwhileitisinon-lineoperation.The

UPSalarm will beep continuously. Immediately remove overloaduntillight

andalarmgoesoff.Ifyoudonotimmediatelyremovetheoverload,theUPS

willtransferfromon-linetobypassoperation.

“BATT LOW” LED: This yellow light will illuminate when your UPS’s

batterychargelevelislow.TheUPSalarmwill beepuntileitherthebattery

chargeisdepletedorthebatteriesareadequatelyrecharged.

“ON BATT” LED:Thisgreenlightwillilluminateconstantlytoindicatethat

AClinevoltageisnotpresentandyourUPSisprovidingyourequipmentwith

batterypower.TheUPSwillalsobeepeverytwoseconds,unlesssilencedby

the“ON/TEST”Button.Whenthislightisilluminated,youcanmonitorthe

batterychargelevelofyourUPSonthe“BATTACTIVEMETER”LEDs.

Basic Operation (continued)

200907169 93-2615.indd 7 8/11/2009 10:15:03 AM

Rear Panel

“REPLACE BATT” LED:Thisredlightwillilluminateconstantlyandthe

UPSalarmwillbeepevery2secondsifyourUPS’smicroprocessordetectsa

batteryfaultorifyourUPSfailstheautomaticself-test(afteryouturnyour

UPSON)andtheUPSbatteryislessthanfullycharged.LettheUPSsystem

charge for at least 12 hours and perform a self test using the “ON/TEST

Button”asdescribedonpage6.Ifthelightcontinuestostayon,contactTripp

Liteforservice.

Accessory Slot:Removethesmallcoverpanelfromthisslottouseoptional

accessories to remotely monitor and control your UPS. Contact Tripp Lite

CustomerSupportat(773)869-1234formoreinformation,includingalistof

availableSNMP,networkmanagementandconnectivityproducts.

External Battery Pack Connector (configuration varies by model):Useto

connect optional Tripp Lite Battery Packs for additional runtime. Contact

TrippLiteCustomerSupportat(773)869-1234fortheappropriateTrippLite

batterypacktoconnect.RefertoinstructionsavailablewiththeBatteryPack

forcompleteconnectioninformationandsafetywarnings.

Fan:ThefancoolstheUPS’sinternalcomponents.Itisalwaysonwhenline

powerispresent.

Input Circuit Breaker Switch:Thisresettable breaker preventshigh input

current from damaging the UPS or the attached load. If this breaker trips,

makesureyourUPSisconnectedtoACpowerofthepropervoltagebefore

resettingthecircuitbreakerbypushingthebreakerswitchin.

Ground Screw: Use this to connect any equipment that requires a chassis

ground.

Output Circuit Breakers Switches (HTR22-3U): These resettable circuit

breakersprotectyourUPSfromoutputoverload.Ifoneorbothbreakerstrip,

removesomeoftheloadonthecircuit(s)andallowtheUPStocoolbefore

pressingthebreakerswitch(es)intoreset.

Input Cord:ThispermanentlyattachedpowercordconnectsyourUPStoa

poweroutlet.

Front Panel Indicator Lights continued

Basic Operation (continued)

200907169 93-2615.indd 8 8/11/2009 10:15:04 AM

Rear Panel continued

AC Receptacles (Varied by Model): These15-,20-and30-ampreceptacles

provideyourconnected equipment with puresine-waveACoutputfromthe

AClineduringnormaloperationandfrombatterypowerduringblackoutsand

severe brownouts. Power provided at these outlets is filtered to protect

connectedequipmentagainstdamagingsurgesandlinenoise.Thereceptacles

are divided into numbered load banks, as labelled on the unit. Using

PowerAlertsoftwareandcabling,loadbanksoneandtwomaybeindividually

turned off and on from a remote location, allowing users to reset or reboot

connectedequipment.

Phone/Network Line Surge Suppression Jacks: If your UPS is equipped

withthesejacks,theywillprotectconnectedequipmentagainstsurgesovera

phoneornetworkline.Connectingyourequipmenttothesejacksisoptional;

your UPS will work properly without this connection. For connection

instructions, see “Optional Connections” in the Installation section.

Not compatible with PoE (Power Over Ethernet) applications.

USB or DB9 Communication Port (select models only):These ports can

connect your UPS to any computer for automatic file saves and unattended

shutdownintheeventof a powerfailure.Use with TrippLite’s PowerAlert

SoftwareandappropriateUSBorDB9cable.APowerAlertCDandUSBor

DB9cablemaybeincludedwithyourUPS;ifso,inserttheCDintotheCD

trayofyourcomputerandfollowtheinstallationinstructions.IfPowerAlert

Software and the appropriate cable did not come with your UPS, you can

obtain the software FREE via the Web at www.tripplite.com. Any user-

suppliedDB9pass-throughorUSBcablemaythenbeusedtoconnectyour

UPStoyourcomputer.NOTE: This connection is optional. The UPS will work

properly without this connection.

TheDB9portcanbeusedtomonitorandcontrolyourUPSusingeitherRS-

232ordrycontactprotocols.

RS-232communicationsarecomplexbuteasytoimplementbyusingaDB9

cabletoconnecttheUPStoacomputerwithTrippLitePowerAlertSoftware

installed.

Drycontactcommunicationsaresimple,butsomeknowledgeofelectronicsis

necessarytoconfigurethem.TheDB9port'spinassignmentsareshowninthe

diagramattheleft.

Units with both USB and DB9 ports: If the UPS battery is low, the UPS

sendsasignalbybridgingpins1and5.Ifutilitypowerfails,theUPSsendsa

signal by bridging pins 8 and 5. To shut the UPS down remotely, short pin

3~pin9foratleast3.8seconds.

Units with DB9 ports only: IftheUPSbatteryislow,theUPSsendsasignal

by bridging pins 1 and 5. If utility power fails, the UPS sends a signal by

bridgingpins8and5.ToshuttheUPSdownremotely,senda5Vto12Vsignal

onpin3(usingpin5asthenegativeground)foratleast3.8seconds.

EPO (Emergency Power Off) Port: Selectmodelsfeaturea EPOport that

may be used to connect the UPS to a contact closure switch to enable

emergencyinvertershutdown.SeeOptionalInstallation.

NEMA 5-15R

Other outlet types not shown

Communications

Basic Operation (continued)

USB Port

(Select Models)

DB9 Port

200907169 93-2615.indd 9 8/11/2009 10:15:05 AM

TheUPS’scontrolpanellightswillturnoninthesequencesbelowtosignalthattheUPSishaving

operationaldifficulties.

Lights (On/Flashing) and Condition Solution

On: REPLACE BATT Let the UPS system charge for at least 12 hours

Condition: Replace Battery and perform a self test using the "ON/Test

Switch" as described on page 6. If the light

continues to stay on, contact Tripp Lite for service.

On: BATT LOW, ON BATT Prepare for imminent UPS shutdown.

Condition: Battery Low

On: BYPASS, LINE, LOAD, OVERLOAD Reduce the load the UPS supports.

Condition: On Bypass due to Overload

Flashing: OVERLOAD Remove the cause of the short circuit

Condition: Short Circuit from the UPS output.

On: FAULT Check the utility line for wiring problems such as

Condition: Wiring Fault reversed line and neutral or a missing ground.

On: FAULT, 100% Restart the UPS. If the problem persists,

Condition: Battery Voltage too High contact Tripp Lite for repairs.

On: FAULT, BYPASS, LINE, 50% Restart the UPS. If the problem persists,

Condition: On Bypass due to contact Tripp Lite for repairs.

High Output Voltage

On: FAULT, BYPASS, LINE Restart the UPS. If the problem persists,

Flashing: 50% contact Tripp Lite for repairs.

Condition: On Bypass due to

Low Output Voltage

On: FAULT, BYPASS, LINE, 25% Restart the UPS. If the problem persists,

Condition: On Bypass due to High contact Tripp Lite for repairs.

Bus Voltage

On: FAULT, BYPASS, LINE Restart the UPS. If the problem persists,

Flashing: 25% contact Tripp Lite for repairs.

Condition: On Bypass due to Low

Bus Voltage

On: BYPASS, LINE Check the UPS to be sure that there is

Flashing: FAULT adequate space for air to circulate near

Condition: On Bypass due to High the vents and that the fan is working

Internal Temperature properly. Restart the UPS.

Flashing: LINE This indicates that utility power is too high or low

Condition: Input Abnormal for the UPS to operate in BYPASS mode, so if an

inverter failure occurs, the UPS will deliver no output.

On: FAULT, 50% Restart the UPS. If the problem persists,

Flashing: LINE contact Tripp Lite for repairs.

Condition: No Output due to High

Output Voltage and Abnormal Input

On: FAULT

Restart the UPS. If the problem persists,

Flashing: LINE, 50% contact Tripp Lite for repairs.

Condition: No Output due to Low

Output Voltage and Abnormal Input

On: FAULT, 25% Restart the UPS. If the problem persists,

Flashing: LINE contact Tripp Lite for repairs.

Condition: No Output due to High

Bus Voltage and Abnormal Input

On: FAULT Restart the UPS. If the problem persists,

Flashing: LINE, 25% contact Tripp Lite for repairs.

Condition: No Output due to Low

Bus Voltage and Abnormal Input

Flashing: LINE, FAULT Check the UPS to be sure that there is adequate

Condition: No Output due to High space for air to circulate near the vents and that

Internal Temperature and Abnormal the fan is working properly. Restart the UPS.

Input If the problem persists, contact Tripp Lite for repairs.

Troubleshooting

200907169 93-2615.indd 10 8/11/2009 10:15:05 AM

Altri manuali per SmartOnline 2-9USTAND

Indice

Altri manuali Tripp Lite UPS

Tripp Lite

Tripp Lite ECO-UPS ECO650LCD Manuale utente

Tripp Lite

Tripp Lite SmartOnline S3MX Manuale utente

Tripp Lite

Tripp Lite SMART1000RMXL2U Manuale utente

Tripp Lite

Tripp Lite SmartOnline SU2200XL Manuale utente

Tripp Lite

Tripp Lite SmartPro SMART750RM1U Manuale utente

Tripp Lite

Tripp Lite SmartOnline Manuale utente

Tripp Lite

Tripp Lite SmartPro Series Manuale utente

Tripp Lite

Tripp Lite RBC6A Manuale utente

Tripp Lite

Tripp Lite SMART1500LCDXL Manuale utente

Tripp Lite

Tripp Lite SmartPro 2200XLT Manuale utente

Tripp Lite

Tripp Lite SUPDM16 Manuale utente

Tripp Lite

Tripp Lite SmartOnline SU2200RTXL2UA Manuale utente

Tripp Lite

Tripp Lite Digital UPS Systems 200703079 Manuale utente

Tripp Lite

Tripp Lite 1400VA Manuale utente

Tripp Lite

Tripp Lite UPS System AVRX550U Manuale utente

Tripp Lite

Tripp Lite SmartPro SMART700RT1U Manuale utente

Tripp Lite

Tripp Lite SmartOnline SU1500XL Manuale utente

Tripp Lite

Tripp Lite Omni VS Manuale utente

Tripp Lite

Tripp Lite SmartOnline 220/230/240V Input/Output Manuale utente

Tripp Lite

Tripp Lite SMART1524ET Manuale utente

Tripp Lite

Tripp Lite BCPERS450 Manuale utente

Tripp Lite

Tripp Lite SmartPro SMC10002URM Manuale utente

Tripp Lite

Tripp Lite ECO-UPS ECO650LCD Manuale utente

Tripp Lite

Tripp Lite AVRX Series Manuale utente

Manuali UPS popolari di altre marche

Pylontech

Pylontech Victron & Pylontech US5000 Manuale utente

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuale utente

Mecer

Mecer ME-1000-WTU Manuale utente

Mustek

Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento

Emerson

Emerson Liebert NXL series Manuale utente

MAKELSAN

MAKELSAN BOXER SERIES Manuale utente

Block

Block PC-0524-400-0 Manuale utente

CyberPower

CyberPower CP585LCD Manuale utente

Eaton

Eaton 3S Istruzioni per il montaggio

CyberPower

CyberPower Office Tower Series UPS 1000 Manuale utente

CyberPower

CyberPower BM100 Manuale utente

Best Power

Best Power 610 Manuale utente

Best Power

Best Power Unity/I UT3K Manuale utente

Mustek

Mustek PowerMust 400 Offline Manuale utente

Xantrex

Xantrex Trace 512 UR-UPS Manuale utente

Forza

Forza SL-1501UL Manuale utente

LEGRAND

LEGRAND keor 310081 Manuale utente

ABB

ABB Conceptpower DPA 500 Manuale utente