Tripp Lite SmartOnline Manuale utente

Owner’s Manual

SmartOnline®

Rack/Tower On-Line UPS Systems

Not suitable for mobile applications.

1. Important Safety Instructions 2

2. Installation 3

2.1 Mounting (Rack) 3

2.2 Mounting (Tower) 4

2.3 Connection and Start-Up 4

2.4 Optional Connections 5

3. Operation 8

3.1 Front Panel Switches 8

3.2 Advanced Operational 8

Settings

3.3 Front Panel Indicator Lights 9

3.4 Rear Panel 11

3.5 Communications 12

4. Troubleshooting 13

5. Battery Replacement 14

6. Storage and Service 16

6.1 Storage 16

6.2 Service 16

7. Product Registration and 17

Regulatory Compliance

Español 18

Français 35

Русский

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

PROTECT YOUR INVESTMENT!

and ultimate peace of mind.

You could also win an

ISOBAR6ULTRA surge protector—

a $100 value!

www.tripplite.com/warranty

17-06-040-932882.indb 1 6/29/2017 10:33:09 AM

1. Important Safety Instructions

UPS Location Warnings

• Install the UPS system indoors, away from excess moisture or heat, conductive

contaminants, dust or direct sunlight.

• For best performance, keep the indoor temperature between 32º F and 104º F

(0º C and 40º C).

• Leave adequate space around all sides of the UPS system for proper ventilation.

• Do not mount the UPS system with its front or rear panel facing down (at any angle).

Mounting in this manner will seriously inhibit the UPS system’s internal cooling,

eventually causing product damage not covered under warranty.

UPS Connection Warnings

• Connect the UPS system directly to a properly grounded AC power outlet. The outlet

must be installed near the UPS system and must be easily accessible for disconnection.

• To reduce the risk of fire, connect only to a circuit provided with 20 amperes maximum

branch circuit overcurrent protection in accordance with your local and National

Electrical Code (NEC), ANSI/NFPA 70.

• Do not modify the UPS system’s plug, and do not use an adapter that would eliminate

the UPS system’s ground connection. Do not plug the UPS system into itself; this will

damage the UPS system.

• Do not use extension cords to connect the UPS system to an AC outlet.

• If the UPS system receives power from a motor-powered AC generator, the generator

must provide clean, filtered, computer-grade output.

Equipment Connection Warnings

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to

significantly affect its safety or effectiveness is not recommended.

• Do not connect surge suppressors or extension cords to the output of the UPS system.

This might damage the UPS system and may affect the surge protector and UPS system

warranties. Connecting a Tripp Lite power distribution unit (PDU) to the output of the

UPS system is safe and will not void the warranty.

Battery Warnings

• Refer to Section 5: Battery Replacement for a complete list of battery warnings.

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during

the installation, operation and storage of this product. Failure to heed these

warnings may affect the warranty.

17-06-040-932882.indb 2 6/29/2017 10:33:15 AM

2. Installation

2.1 Mounting (Rack)

• Use the included rackmount shelves and mounting hardware to mount the UPS system

in a 4-post rack or rack enclosure. To mount the UPS system in a 2-post (telecom) rack,

order Tripp Lite’s 2-Post Rackmount Kit (model 2POSTRMKITWM, sold separately).

• The instructions in this manual are for common rack and rack enclosure types and may

not be appropriate for all mounting applications. The user must determine the fitness of

hardware and procedures before mounting. If hardware or procedures are not suitable

for the application, contact the manufacturer of the rack or rack enclosure for a

solution.

Warning: The UPS system is very heavy—be careful when moving or lifting it.

4-Post Mounting Procedure

1The included plastic pegs Awill support the

empty rackmount shelves Buntil the

permanent mounting hardware is installed.

Insert a peg near the center of the front and

rear bracket of each shelf as shown. (Each

front bracket has six holes and each rear

bracket has three holes.) The pegs will snap

into place.

After installing the pegs, expand each shelf to

match the depth of the vertical rack rails. The

pegs will fit through the square holes in the

rack rails to support the shelves. Confirm that

the shelves are level in all directions.

Note: The support ledge of each shelf must face

inward.

2Secure the shelves Bto the rack rails

permanently using the longer included screws

and washers Cas shown. (Place four screws

at the front and four screws at the back.)

Tighten all screws before proceeding.

Warning: Do not attempt to install

the UPS system until the required

screws have been inserted and

tightened. The plastic pegs will not

support the weight of the UPS

system.

3Attach the mounting brackets Dto the

forward mounting holes of the UPS system

using the shorter included screws E. The

mounting bracket ears must face forward.

4With the aid of an assistant, lift the UPS system and slide it onto the mounting

shelves. Insert four of the included screws Fthrough the mounting bracket ears and

into the vertical rack rails. Tighten all screws securely.

17-06-040-932882.indb 3 6/29/2017 10:33:19 AM

Some models may differ.

Voltage Selection Mode

Please follow below procedure to select the

output voltage by front panel.

1. Press the ON/TEST and OFF buttons

simultaneously to enter “Voltage Selection”

mode. The three LEDs labeled VOLTAGE

SELECTION MODE will flash when you have

entered this mode.

2. Press the ON/TEST button to select the

output voltage from 200 to 240.

3. After selecting the desired output voltage,

press the ON/TEST and OFF buttons

simultaneously to save your selection and

exit “Voltage Selection” mode.

2. Installation

2.2 Mounting (Tower)

The UPS system can be mounted in an upright

tower position when used with Tripp Lite’s

optional base stand kit (model 2-9USTAND, sold

separately). When mounting the UPS system in a

tower position, make sure the control panel is

closer to the top of the cabinet than the bottom.

The control panel can be rotated to match the

orientation of the UPS system. Pull the panel

out, rotate it and push it back into place as

shown.

Warning: The UPS system is very

heavy—be careful when moving or

lifting it.

2.3 Connection and Start-Up

1Plug the UPS system into an electrical

outlet.

Note: The UPS system does not include an input

power cord.

Connect a user-supplied power cord to the

IEC-320-C20 input receptacle. The power

cord should have an IEC-320-C19 connector

on one end and a plug appropriate for your

local site’s utility outlet on the other end.

The UPS system must be connected to a

dedicated circuit of sufficient amperage.

Refer to the UPS system nameplate for input

requirements.

After the UPS system is plugged in, the

following sequence of events will occur:

1. The fan will turn on and all LEDs will

illuminate momentarily.

2. The percent level LEDs (25%, 50%, 75%

and 100%) will illuminate one at a time.

3. The “LINE” and “LOAD” LEDs will

illuminate to indicate normal operation.

Note: Power will not be supplied to the outlets until

the UPS system is turned on.

17-06-040-932882.indb 4 6/29/2017 10:33:21 AM

Voltage Note: The UPS system supports a nominal AC voltage setting of 200V, 208V, 220V, 230V

or 240V. 230V is the factory default setting. The full output capacity of 2,500 watts is available

when the UPS system is set at 230V or 240V. When the UPS system is set at 200V, 208V or

220V, output capacity is reduced to 2,400 watts. The nominal voltage setting can be changed

using the control panel buttons, with PowerAlert®software or the optional WEBCARDLX internal

accessory card. See the PowerAlert software or WEBCARDLX documentation for more information

about changing the nominal voltage setting.

Some models may differ.

2. Installation

2Plug equipment into the UPS system’s AC

outlets.

Note: Use the supplied C13 to C14 interconnection

cord.

The UPS system is designed to support

computer equipment only. The UPS system

will become overloaded if household

appliances or laser printers are connected to

its outlets.

Note: Additional interconnection cords (C13 to

C14) are available from Tripp Lite. Visit www.

tripplite.com. (Part # P004-006)

3Turn the UPS system ON.

To turn on the UPS system, press the “ON/

TEST” button for approximately one second

until the UPS system beeps, then release the

button.

The UPS system will begin providing AC power

to its outlets. The “ON LINE” LED will

illuminate.

Note: UPS system will function properly upon initial

startup, however, maximum runtime for the unit’s

battery will only be accessible after it has been

charged for 24 hours.

17-06-040-932882.indb 5 6/29/2017 10:33:22 AM

4-5

2a Some models may differ.

1USB and RS-232 Serial Communications

Use the included USB cable 1a or RS-232

(DB9) serial cable 1b to connect the UPS

system’s communication port to a

computer’s communication port. Install the

included PowerAlert software on the

computer. (See the PowerAlert software

documentation for system requirements and

installation instructions.)

2EPO Port Connection

This optional feature is only for those

applications that require connection to a

facility’s Emergency Power Off (EPO) circuit.

When the UPS is connected to this circuit, it

enables emergency shutdown of the UPS’s

inverter and inhibits transfer to internal

bypass. Using the cable provided, connect

the EPO port of your UPS 2a to a user-

supplied normally closed or normally open

switch according to the circuit diagram 2b .

Notes:

1. If using a cable other than what is supplied, the

cable should not have a resistance of greater

than 5 ohms.

2. If a non-latching EPO switch is used, the EPO

must be held for a minimum of 1 second. This

does not apply to a latching EPO switch.

CAUTION: The EPO port is not a

phone line surge suppressor; do

not connect a phone line to this

port.

1b Some models may differ.

1a Some models may differ.

2. Installation

2.4 Optional Connections

The UPS system will function properly without these connections.*

* Note: PowerAlert software (included) or the optional WEBCARDLX internal accessory card is required

to control some of the advanced features of the UPS system, including economy mode and frequency

conversion settings. The factory defaults are suitable for most applications.

UPS Unit State when asserting EPO with AC line present:

LEDs Output Fans Serial SNMP USB

OFF OFF ON ON ON ON

To restart the UPS unit after asserting EPO with AC line present:

1. Verify that the EPO assertion has been removed or cleared.

2. Remove AC line power to the UPS unit.

3. Reapply AC line power. Now the UPS will start back up in Standby mode.

17-06-040-932882.indb 6 6/29/2017 10:33:24 AM

Some models may differ.

UPS Unit State when asserting EPO without AC line power:

LEDs Output Fans Serial SNMP USB

OFF OFF OFF OFF OFF OFF

To restart the UPS unit after asserting EPO without AC line power:

1. Verify that the EPO assertion has been removed or cleared.

2. Reapply AC line power to the UPS unit. Now the UPS will start back up in Standby mode.

3External Battery Connection

4Accessory Card Slot

The slot accommodates an optional internal

accessory card (model: WEBCARDLX, sold

separately). WEBCARDLX provides an

Ethernet network interface for remote

monitoring and control of the UPS system via

SNMP, Web or telnet. WEBCARDLX enables

remote reboots, shutdowns, load monitoring,

condition reporting and more. Use

WEBCARDLX with an optional environmental

sensor (model E2MT, E2MTDI, E2MTDO and

E2MTHDI, sold separately) to monitor

temperature and humidity or to control and

monitor alarms and security systems.

Remove the cover panel from the slot to

insert the accessory card. Refer to the

WEBCARDLX documentation for additional

installation instructions.

2. Installation

17-06-040-932882.indb 7 6/29/2017 10:33:26 AM

3. Operation

3.1 Front Panel Switches

“ON/TEST” Button: This button controls four separate functions:

UPS System Power ON

To turn on the UPS system, press the “ON/TEST” button for

approximately one second until the UPS system beeps, then release

the button. The “ON LINE” LED will illuminate.

UPS System Self-Test

To initiate a self-test of the battery during normal on-line operation,

press this button for approximately one second until the UPS system

beeps, then release it. The UPS system will shift to battery power for

10 seconds.

Note: All LEDs illuminate during a self-test.

Alarm Silence

To silence the UPS system’s on battery alarm, press this button and

hold it until the UPS system beeps, then release the button.

UPS System Cold Start

To use the UPS system as a stand-alone power source when AC

power is unavailable (i.e. during a blackout), press this button and

hold it until the UPS system beeps, then release the button. The

UPS system will then provide battery power to its outlets.*

* The “ON BATT” indicator light will be illuminated since the UPS system will

be operating from battery power.

“OFF” Button: This button turns off power to the UPS system’s

outlets. Press this button and hold it until the UPS system beeps,

then release it. The battery will continue to charge and the fan will

continue to operate even when the outlets are off. To turn the UPS

system off completely, including the battery charger, unplug the UPS

system’s power cord after pressing the “OFF” switch.

3.2 Advanced Operational Settings

Economy Mode

The UPS system supports economy mode operation to reduce energy consumption and

BTU emissions. In economy mode, the UPS system operates with increased efficiency

when the quality of utility power is satisfactory to pass through to connected equipment

without double conversion.

Economy mode saves energy by suspending double conversion when incoming voltage is

within -12%/+10% of the nominal voltage setting. If the nominal voltage setting is 230V,

the UPS system will remain in economy mode while utility line voltage is between

approximately 202V and 253V. If utility line voltage falls outside this range, the UPS

system will either switch back to standard on-line, double conversion mode or it will switch

to battery backup mode, depending on the severity of the voltage deviation.

Economy mode can be enabled (or disabled) through the included PowerAlert software or

the optional WEBCARDLX internal accessory card. The UPS system's yellow “BYPASS” LED

will illuminate continuously when economy mode is enabled. Refer to the PowerAlert or

WEBCARDLX documentation for more information.

17-06-040-932882.indb 8 6/29/2017 10:33:26 AM

On-line, double-conversion mode (default)

Typical line efficiency at full load: 89%

Output voltage range: ±2% of nominal setting (200/208/220/230/240V)

Economy mode

Typical line efficiency at full load: 97%

Output voltage range: -12%/+10% of nominal setting (200/208/220/230/240V)

Frequency Conversion

The UPS system automatically selects 50 Hz or 60 Hz operation based on utility power

conditions at start-up and regulates output power within ±0.05 Hz of the selected

frequency. The UPS system also has an advanced setting that allows continuous frequency

conversion from 50 Hz to 60 Hz or from 60 Hz to 50 Hz. The advanced frequency

conversion setting is accessible through the included PowerAlert software or the optional

WEBCARDLX internal accessory card. When continuous frequency conversion is enabled,

the maximum output capacity of the UPS system is derated by 25%.

3.3 Front Panel Indicator Lights

Note: All LEDs illuminate during a UPS system self-test.

3. Operation

“ON LINE” LED: This green LED will illuminate continuously to

indicate the UPS system is operating normally in on-line mode

(filtering and resynthesizing AC line input to provide pure sine wave

output). When this LED is illuminated, the load level of the UPS

system is displayed on the % level LEDs (25%, 50%, 75%, 100%).

“LINE” LED: This green LED will illuminate continuously to indicate

the utility-supplied AC line voltage at the wall outlet is nominal. It

will flash if the line voltage is outside the nominal range (either too

low or too high). User action is not required when the LED flashes;

the UPS system continuously and automatically filters AC line

power to provide equipment with pure sine wave AC power,

regardless of brownout or overvoltage conditions. If this LED is off,

then AC line voltage is not present (blackout) or is at an extremely

high voltage, and the UPS system will provide connected

equipment with power from its battery system.

“BYPASS” LED: This yellow LED will illuminate continuously when

the UPS system is in economy mode. The LED will flash when the

UPS system is bypass mode, indicating that the UPS system’s DC/

AC inverter is deactivated. The red “FAULT” LED will also illuminate

if the UPS system is in bypass mode. During normal operation the

bypass LED will illuminate briefly when the unit is plugged in. If an

internal fault or overload occurs, the LED will flash repeatedly to

show that connected equipment will receive filtered AC line power,

but will not receive battery power during a blackout. In this case,

contact Tripp Lite for service.

“FAULT” LED: This red LED will flash when the UPS system detects

an internal fault. If the condition persists after restarting the UPS

system, see Section 4: Troubleshooting.

17-06-040-932882.indb 9 6/29/2017 10:33:27 AM

3. Operation

“LOAD” LED: This green LED will illuminate when the UPS system

is receiving AC power. It also indicates that the % level LEDs (25%,

50%, 75%, 100%) are displaying the UPS load level.

“BATT” LED: This green LED will illuminate when the UPS system

is operating from battery power. It indicates that the % level LEDs

(25%, 50%, 75%, 100%) are displaying the battery charge level.

(The “ON BATT” LED will also be illuminated.)

% Level LEDs: These dual-function LEDs will indicate the % level

for either the load level (if the “LOAD” LED is lit) or the battery

charge level (if the “BATT” LED is lit).

“OVERLOAD” LED: This red LED will illuminate continuously to

indicate that the UPS system’s capacity has been exceeded. The

UPS alarm will beep continuously. Immediately unplug some

equipment until the LED and alarm go off. If the overload is not

corrected immediately, the UPS system will go from on-line to

bypass mode.

“BATT LOW” LED: This yellow LED will illuminate when the UPS

system’s battery charge level is low. The UPS alarm will beep until

the batteries are either depleted or adequately recharged.

“ON BATT” LED: This green LED will illuminate continuously to

indicate that AC line voltage is absent (or out of range) and the

UPS system is providing equipment with battery-derived AC power.

The UPS system will also beep every two seconds (unless silenced

by the “ON/TEST” button) and the % level LEDs (25%, 50%, 75%,

100%) will display the battery charge level.

“REPLACE BATT” LED: This red LED will illuminate continuously

and the UPS alarm will beep every two seconds if the UPS system

fails the automatic self-test. Allow the UPS system to charge for at

least 12 hours and perform a self-test as described in Section

3.1: Front Panel Switches. If the condition persists, contact

Tripp Lite.

17-06-040-932882.indb 10 6/29/2017 10:33:29 AM

Altri manuali per SmartOnline

Indice

Lingue:

Altri manuali Tripp Lite UPS

Tripp Lite

Tripp Lite SmartOnline SU1000XLA Manuale utente

Tripp Lite

Tripp Lite OMNI650LCD Manuale utente

Tripp Lite

Tripp Lite SmartOnline 220/230/240V Input/Output Manuale utente

Tripp Lite

Tripp Lite SmartOnline SU10KRT3U Manuale utente

Tripp Lite

Tripp Lite SmartOnline SU10000RT3U2TF Manuale utente

Tripp Lite

Tripp Lite SmartOnline SU30K3/3 Manuale utente

Tripp Lite

Tripp Lite SmartOnline SU8000RT3UG Manuale utente

Tripp Lite

Tripp Lite OmniSmart OMNIVSINT500 Manuale utente

Tripp Lite

Tripp Lite AG-02F0 Series Manuale utente

Tripp Lite

Tripp Lite SM750XLNAFTA Manuale utente

Tripp Lite

Tripp Lite HTRL15UPS Manuale utente

Tripp Lite

Tripp Lite OmniSmart Manuale utente

Tripp Lite

Tripp Lite SmartOnline Manuale utente

Tripp Lite

Tripp Lite SMART1000LCDU Manuale utente

Tripp Lite

Tripp Lite SmartPro SMX700HG Manuale utente

Tripp Lite

Tripp Lite G1010USB Manuale utente

Tripp Lite

Tripp Lite 1400VA Manuale utente

Tripp Lite

Tripp Lite AGBC5755 Manuale utente

Tripp Lite

Tripp Lite SmartOnline SU3000RTXL2U Manuale utente

Tripp Lite

Tripp Lite SmartPro SMART700SER Manuale utente

Tripp Lite

Tripp Lite SmartOnline SU2200XLNAFTA Manuale utente

Tripp Lite

Tripp Lite SmartOnline SU20KX Manuale utente

Tripp Lite

Tripp Lite SmartOnline SU2200XLA Manuale utente

Tripp Lite

Tripp Lite SmartOnline SU80KX2 Guida all'installazione

Manuali UPS popolari di altre marche

Pylontech

Pylontech Victron & Pylontech US5000 Manuale utente

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuale utente

Mecer

Mecer ME-1000-WTU Manuale utente

Mustek

Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento

Emerson

Emerson Liebert NXL series Manuale utente

MAKELSAN

MAKELSAN BOXER SERIES Manuale utente

Block

Block PC-0524-400-0 Manuale utente

CyberPower

CyberPower CP585LCD Manuale utente

Eaton

Eaton 3S Istruzioni per il montaggio

CyberPower

CyberPower Office Tower Series UPS 1000 Manuale utente

CyberPower

CyberPower BM100 Manuale utente

Best Power

Best Power 610 Manuale utente

Best Power

Best Power Unity/I UT3K Manuale utente

Mustek

Mustek PowerMust 400 Offline Manuale utente

Xantrex

Xantrex Trace 512 UR-UPS Manuale utente

Forza

Forza SL-1501UL Manuale utente

LEGRAND

LEGRAND keor 310081 Manuale utente

ABB

ABB Conceptpower DPA 500 Manuale utente