TrolMaster WD-1 Manuale utente
Overview
Thank you for purchasing the TrolMaster's WD-1 Water Detector. A water
detector is an electronic device that is specially designed to detect the presence
of water and provide an alert in time to allow the prevention of water leakage in
the Aqua-X Irrigation Control System
The default function of Water Dectector (WD-1) is for leak detection and there is
a triangle symbol shown in the LCD display of the Aqua-X Controller. When the
WD-1 detects water leakage, it will send alarm message to your Smartphone
one minute later. You can also check the alarm message in the Aqua-X
Controller.
This unit could be assigned to any controlled output in the system to monitor the
watering schedules. Two or more Water.Detectors ( up to 30pcs for each
system) can be linked together in a "daisy chain," expanding the leak detection
monitoring area.
Features
LCD Display, Easy Operation
Addressing Button
Water Leak Alarm
FRONT PANEL
Installation
Mount the water detector near the water reservoir or nutrient tank. Use a screw
to mount the Water Detector on the wall or fix it through the top hole with a
string.
Operation Instructions
1. Connection to Aqua-X
Connect the RJ12 cable ( left ) to the Water Detector terminal on the bottom
panel of the Aqua-X Controller. The touch spot cable ( right ) can be used to be
connected to a single TSS-1 Touch Spot ( sold separately ) or use a T-Splitter to
connect one more TSS-1 Touch Spot under one Water Detector.
2. Address Assignment
Press the Addressing button on the WD-1unit so that the Aqua-X Controller will
assign an address to the WD-1 unit accordingly. The LCD screen of the WD-1
Water Detector will show a triangle symbol indicating that the water leak
detection is the default function.
3. Leak Sensor & Assignment Settings
There are two functions for each Water Detector, one is Leak Sensor ( water
leak detection ), the other is Assignment ( assigned to any 24V or 110V
controlled output ) as ilustracted below.
NOTE : the number inside the triangle symbol refers to the connection
sequence ( from 1 to 30 ) of the water detectors. The first assigned Water
Detector will be marked as number 1, and the second is number 2 and so on.
a. Leak Sensor ( Leak Detection Mode)
The default function of Water Detector (WD-1) is for leak detection and there is a
triangle symbol shown in the LCD display of the Aqua-X Controller. When WD-1
detects water leakage, it will send an alarm message to your Smartphone one
minute later. You can also check the alarm message in the Aqua-X Controller.
If the Water Detector is NOT in original default function ( leak sensor ), you can
change the Assignment into Leak Sensor as above processes.
b. Assignment ( Output Assigned Mode )
The default mode of Water Detector is in Leak Sensor ( Leak Detection Mode).
You can change the Leak Detection Mode ( Leak Sensor ) into Output Assigned
Mode ( Assignment ) as below processes. As one Water Detector can be
assigned to only one output on any Control Board, you need to select 24V or
110V and one of six outputs to be assigned to the Water Detector. When the
output has been successfully assigned, the Water Detector will send an alarm
message to your Smartphone one minute later when it detects no water on the
reservoirs of the irrigation system.
NOTE :
1. Each Water Detector can be assigned to a Control Board which has been
successfully assigned to the Aqua-X Controller. The Water Detector can not be
assigned to an unassigned Control Board.
2. One Water Detector can be assigned to only one 24V or 110V output. One
Aqua-X Controller can connect up to 30pcs Water Detectors.
3. If the assigned output of that board is offline, the output symbol will blink on
the LCD display of the Aqua-X Controller.
4. If the output is successfully assigned with the Water Detector and the Water
Detector is connected with the Aqua-X Controller, there is a dot before the
assigned output on the Control Board interface as below illustration.
Indice
Altri manuali TrolMaster Sensore di sicurezza
