Trust 400 Manuale utente
TRUST ENERGY PROTECTOR 400
1
UK
Instructions when using for the first time Chapter
1. Connecting (3.1)
2. Use (3.2)
3. Testing (3.3)
1 Introduction
This instruction manual is for users of the ENERGY PROTECTOR 400.
No knowledge of computers is necessary to install this product.
Please contact one of the Trust Customer Care Centers if you have any problems.
2 Safety
Carefully read the following instructions before use:
-Disconnect the power plug from the mains supply before cleaning the device. Do
not use a liquid cleaner or a spray to clean the device. Clean the device with a
damp cloth.
-Do not use this device in a damp environment, such as a bathroom, damp
basement or swimming pool.
-Make sure the UPS is placed on a firm surface, such as your desk or the floor.
-Make sure nothing is placed on the power cable. Do not place this device in an
area where the cable can become worn as a result of people walking over it.
-Never insert objects into the slits on the front of the UPS, because you may touch
live components. This may cause a fire or give you an electric shock.
-Do not try to repair this device yourself. If you open or remove the casing, you
may accidentally touch live components.
-This device may only be repaired by qualified personnel.
-The outputs may have a high voltage, even when the device is turned off.
-Only replace a burnt fuse by the same type of fuse which has the same value.
This will prevent the chance of damage.
-Under the following circumstances, remove the plug from the power socket and
have the device repaired by qualified personnel:
-The cable or plug is damaged.
-Liquid has entered the device.
-The device has been dropped or the casing has been damaged.
-The device is not operating correctly.
BATTERY:
The battery may only be replaced by qualified personnel.
The battery must not be opened or damaged. If the battery is opened or damaged,
electrolyte may be released, which is harmful to skin, eyes and the environment.
To prevent an explosion, do not expose the battery to a naked flame.
!
TRUST ENERGY PROTECTOR 400
2
3 Installation
3.1 Connecting
Note: Turn the computer off before connecting the device.
1 Electricity input for the mains
supply.
2 Electricity output for the
connected device.
3 Fuse holder.
4 Telephone/modem connection IN
5 Telephone/modem connection
OUT
Table 1: Connections
See figure 1.
1. Connect your device to the electricity output (2) on the UPS.
2. Connect the power cable to the electricity input (1) on the UPS.
3. Connect the power cable to the plug socket.
4. Connect the telephone/modem connection IN (4) to the telephone socket.
5. Connect the telephone/modem cable for your telephone/modem to the
telephone/modem connection OUT (5) on the UPS.
6. Your device is now protected against a power surge and the loss of power.
3.2 Use
1 ON / OFF button
2 LED indicator for normal use (green). This is lit if
there is sufficient mains power and the battery is
being charged.
3 LED indicator for battery power (yellow). This is lit if
there is no longer a mains supply and your device
is powered by the UPS.
4 LED indicator for an empty battery (red). This is lit if
the battery is empty or if the battery must be
replaced because it is faulty.
See figure 2.
Note: The battery is charged when the plug is inserted into the plug socket.
Charge the battery for 4 hours before use.
TRUST ENERGY PROTECTOR 400
3
UK
3.3 Checking after the installation
Note: The FAQ’s for simple questions and solutions can be found at
www.trust.com/13163.
The UPS can be tested by disconnecting the power cable (do this after the UPS has
been charged for at least 4 hours).
4 Troubleshooting
Method
1. Read the solutions given below.
2. Check for up-to-date FAQ’s, drivers and instruction
manuals on the Internet (www.trust.com/13163).
Problem Possible cause Solution
The ON/OFF button has
not been pressed or has
not been pressed for long
enough.
Press the ON/OFF button for
more than 3 seconds.
The UPS is not
turned on. The
indicator is not
lit.
The battery voltage is too
low.
Recharge the UPS.
The power cable is loose. Connect the power cable
correctly.
The fuse is burnt. Replace the fuse.
The UPS
remains in the
battery mode.
The mains supply is too
high, too low or there is a
power failure.
This is normal. If this lasts for a
long period of time, contact
your electricity supplier.
The backup time
is too short.
The battery has not been
fully charged.
Recharge the UPS.
The UPS is placed under
a heavy load.
Disconnect the less important
devices.
There is a
continuous
beeping noise. The battery voltage is too
low.
Recharge the UPS.
The red LED is
lit.
The battery is empty. Fully recharge the UPS. If this
does not solve the problem, the
battery must be replaced.
!
TRUST ENERGY PROTECTOR 400
4
If you still have problems after trying these solutions, please contact one of the Trust
Customer Care Centers. You can find more information at the back of this instruction
manual. Please have the following information available:
•The article number. This is 12275.
•A good description of what does not work.
•A good description of when the problem occurs.
5 Technical specifications
Input voltage 165 VAC - 280 VAC
Frequency 50 Hz ± 5%
Power output [VA] 400
Battery type Lead-acid maintenance-
free
Battery capacity 7 Ah
Charging time 8 hours
Surge current protection [KJ] 0.320
RFI filter Yes
Number of outputs 2
Altri manuali Trust UPS
Trust
Trust 17938 Manuale utente
Trust
Trust PW-5060S 600VA UPS Manuale utente
Trust
Trust PW-4130M 1300VA MNGT UPS Manuale utente
Trust
Trust UPS 1000 VA Manuale utente
Trust
Trust 17681 Manuale utente
Trust
Trust 17678 Manuale utente
Trust
Trust PW-4000T Manuale utente
Trust
Trust 18162 Manuale utente
Trust
Trust 1000 Manuale utente
Trust
Trust PW-4040T Manuale utente
Trust
Trust PW-4120M Manuale utente
Trust
Trust Energy Protector 325 Manuale utente
Trust
Trust 14948 Manuale utente
Trust
Trust PW-4055T Manuale utente
Trust
Trust 17238 Manuale utente
Trust
Trust Wireless Tablet Series Manuale utente
Trust
Trust PW-5040S Manuale utente
Trust
Trust 1300 VA Manuale utente
Trust
Trust 14948 Manuale utente
Manuali UPS popolari di altre marche
Pylontech
Pylontech Victron & Pylontech US5000 Manuale utente
Tecnoware
Tecnoware EVO DSP PLUS MM 6.8 Manuale utente
Mecer
Mecer ME-1000-WTU Manuale utente
Mustek
Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento
Emerson
Emerson Liebert NXL series Manuale utente
MAKELSAN
MAKELSAN BOXER SERIES Manuale utente
