TSC TTP-2410M Manuale utente

Altri manuali per TTP-2410M

2

Questo manuale è adatto per i seguenti modelli

4

Indice

Altri manuali TSC Lettore di codici a barre

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Datalogic

Datalogic Heron HD3130 Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente

TTP-2410M/346M/644M

TTP-246M Plus/344M Plus

Bar Code Printer Service Manual

38

38

4.2 Mechanism Fine Adjustment to Avoid Ribbon Wrinkles

This printer has been fully tested before delivery. There should be no ribbon wrinkle

presented on the media for general-purpose printing application. Ribbon wrinkle is related to

the media thickness, print head pressure balance, ribbon film characteristics, print darkness

setting…etc. In case the ribbon wrinkle happens, please follow the instructions below to

adjust the printer parts.

Adjustable

Printer

Parts

Symptom 1. Wrinkle happens from label lower left to

upper right direction ("Ԩ")

2. Wrinkle happens from label lower right

to upper left direction ("Ԫ")

Wrinkle

Example

Feed direction

Ribbon guide plate

Print head pressure

adjustment knob Z-axis mechanism

adjustment knob

TTP-2410M/346M/644M

TTP-246M Plus/344M Plus

Bar Code Printer Service Manual

39

39

Adjust the print head pressure adjustment knob

The print head pressure adjustment knob has 5

levels of settings. Clockwise direction adjustment

is to increase the print head pressure. Counter

Clockwise adjustment can decrease the print

head pressure.

If the wrinkle on the label starts from the lower left

side to upper right side, please do following

adjustment.

1. Decrease the right side print head pressure

adjustment knob setting 1 level per each

adjustment then print the label again to check if

wrinkle is gone.

2. If the right side print head adjustment knob

setting has been set to index 1 (the lowest

pressure index), please increase the left side

print head pressure.

3. If the left side print head adjustment knob

setting has been set to 5 (the highest pressure

index) the wrinkle can’t be avoid, please rotate

the both knobs back to setting 1 then rotate the

Z-axis mechanism adjustment knob clockwise

for a few degrees and print again for fine tune

the print head pressure distribution.

Note for step 3:

*Factory default setting, the Z-axis knob is rotated

counter clockwise to the end of thread.

*Turn the Z-axis mechanism adjustment knob

clockwise until you feel the knob touch the

mechanism for the first adjustment.

* If the wrinkle is still there, please turn the Z-axis

mechanism adjustment knob clockwise about

1/4 circle each time for adjustment

* If the winkled direction is change from "Ԩ" to "

Ԫ" by adjusting the Z-axis mechanism

adjustment knob, please turn the Z axis

mechanism adjustment knob counter clockwise

to avoid the wrinkle.

Adjust the print head pressure adjustment knob

The print head pressure adjustment knob has 5

levels of settings. Clockwise direction adjustment

is to increase the print head pressure. Counter

Clockwise adjustment can decrease the print

head pressure.

If the wrinkle on the label starts from the lower

right side to upper left side, please do following

adjustment.

1. Decrease the left side print head pressure

adjustment knob setting 1 level per each

adjustment then print the label again to check if

wrinkle is gone.

2. If the left side print head adjustment knob level

has been set to index 1 (the lowest index),

please increase the right side print head

pressure.

Right knob

Left knob Right knob

Left knob

Z axis mechanism

adjustment knob