TV Logic LVM-170W (G) Manuale utente

Multi

Multi-Format LCD Monitors

LVM Series

User’s Manual

LVM-170W (G)

LVM-230W

LVM-240W

Warning

· Always use set voltage.

- AC 100 ~ 240V (1.8A/50~60Hz)

- DC 24V (6A) [Only LVM-240W(G)]

· If liquid is spilled on or impacts this product, please disconnect

the product immediately and seek professional help before continued use.

· Keep unit disconnected during extended periods of disuse.

Keep unit in a well-ventilated place to prevent overheating.

Do not install the product near any heat-generating equipment.

Also, keep the product out of direct sunlight or dusty areas.

Only clean the product with a noncommercial, mild and neutral detergent.

When transporting the product, make use of its original packaging for safer carriage.

FCC (Federal Communications Commission)

This equipment has been tested and found to comply with the limits for class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interface when the equipment is operated in a commercial

environment.

This equipment generates, uses, and can radiate radio frequency energy, and if not installed

and used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential to correct the interference at

his own expense

Warning!! : Change or modifications not expressly approved by the manufacturer

responsible for compliance void the user’s authority to operate the equipment.

Disposal of Old Electrical & Electronic Equipment

(Applicable in the European Union and other European

countries with separate collection systems)

This symbol on the product or on its packing indicates that this product shall not be treated

as household waste. Instead it shall be handed over to the applicable collection point for

the recycling of electrical and electronic equipment. By ensuring this product is disposed

of correctly, you will help prevent potential negative consequence for the environment and

human health, which could otherwise be caused by inappropriate waste handling of this

product. The recycling of materials will help to conserve natural resources.

Features

LVM Series units have the following features:

Compatible with varied SDI signals

The product is compatible with varied SDI Signals

- 480i, 576i, 720p, 1080i, 1080p, 1080psF (SDI A, B 2 channel compatible)

Compatible with varied analog signals

The product is compatible with varied analog signals

- Composite, S-Video, Component, RGB, etc.

All-in-one system

Slim and all-in-one type monitor that requires no additional accessories,

which provides optimized space utilization.

Wide Screen compatible

Wide Screen for easier monitoring.

DC/AC compatible

The product may be powered by normal AC source, but also 24V DC source.

Remote control function

Remote-controlled simply with cable connection without additional

peripheral equipment attached to unit.

DVI function built-in

DVI Input is available without any other accessory.

Dual Link support (Option)

LVM-170W (LVM-230W/LVM-240W) can use 4:4:4 format and 1080/60p.

Additional Features

Wide Viewing Angle, Reclocked Active Through OUT (SDI), VESA Mounting Standard,

1000:1 contrast ratio(LVM-240W), 500cd brightness, OSD user interface, rack mountable.

* LVM-230W contrast ratio 800:1 / LVM-170W contrast ratio 400:1

LVM-170W (G) / 230W / 240W

Name & Function of Each Part

LVM-170W (G)

<FRONT>

<REAR>

TALLY

ANALOG INPUT

SDI INPUT SELECT

UNDER SCAN

ASPECT

MARKER

H/V DELAY

STAND BY

ENTER

UP / CONTRAST

DOWN / BRIGHT

CHROMA/PHASE

BLUE ONLY

REMOTE

DVI IN / FACTORY PGM

CVBS1 / Y / G / S-Y

CVBS2 / Pb / B

CVBS3 / Pr / R / S-C

SDI-IN A

SDI-OUT A

SDI-IN B

SDI-OUT B

~AC IN

LVM-170W (G) / 230W / 240W

<FRONT>

LVM-230W

<REAR>

TALLY

ANALOG INPUT

SDI INPUT SELECT

UNDER SCAN

ASPECT

MARKER

H/V DELAY

STAND BY

ENTER

UP / CONTRAST

DOWN / BRIGHT

CHROMA/PHASE

BLUE ONLY

REMOTE

DVI-I IN / FACTORY PGM

CVBS1 / Y / G / S-Y

CVBS2 / Pb / B

CVBS3 / Pr / R / S-C

SDI-IN A

SDI-OUT A

SDI-IN B

SDI-OUT B

~AC IN

LVM-170W (G) / 230W / 240W

<FRONT>

LVM-240W

<REAR>

TALLY

ANALOG INPUT

SDI INPUT SELECT

UNDER SCAN

ASPECT

MARKER

H/V DELAY

STAND BY

ENTER

UP / CONTRAST

DOWN / BRIGHT

CHROMA/PHASE

BLUE ONLY / MONO

REMOTE

DVI-I IN / FACTORY PGM

CVBS1 / Y / G / S-Y

CVBS2 / Pb / B

CVBS3 / Pr / R / S-C

SDI IN-A

SDI OUT-A

SDI IN-B

SDI OUT-B

DC 24V

~AC IN

LVM-170W (G) / 230W / 240W

<FRONT>

· ANALOG INPUT

Used to select desired ANALOG INPUT. A Sub Menu for each analog input

connected can be selected.

· SDI INPUT SELECT

Used to select SDI INPUT A or B.

· UNDER SCAN

Used to transfer from OVER SCAN mode to UNDER SCAN mode.

(Compatible up to SD 1:1 SCAN mode.)

· ASPECT

Used to change the monitor ratio on SD signal mode to 16:9.

· MARKER

Used to show MARKER on the screen. The type of marker at work may be selected

on the main menu.

· H/V DELAY

Used to observe horizontal sync and vertical sync simultaneously.

· BLUE ONLY / MONO

You may remove R(red) and G(green) from the input signal and play the screen only

with B(blue) signal. Button may be pressed twice to change the screen to MONO

mode. (This mode uses only luminance value.)

· CHROMA/PHASE

Used to change the CHROMINANCE and PHASE values. Pressing the button once

will activate the CHROMA mode, pressing the button twice activates PHASE mode.

(PHASE may be used only with COMPOSITE and S-VIDEO on ANALOG mode.)

LVM-170W (G) / 230W / 240W

· MENU

Used when OSD menu is activated.

· DOWN/BRIGHT

Used to navigate menu during OSD menu activation. It may also be used to control

the BRIGHT value when the OSD menu is not active.

· UP/CONTRAST

Used to navigate the menu during OSD menu activation. It may also be used to

control the CONTRAST value when the OSD menu is not active.

· ENTER

Used to confirm a chosen value (or mode) during OSD menu activation or inactivation.

· STANDBY

Indicates power supply connection and current setting. The lamp is RED when unit is

connected to power supply and in standby mode and GREEN during system operation.

In case of sudden loss of power unit retains last setting.

· TALLY

LED indicating monitors current status

LVM-170W (G) / 230W / 240W

<REAR>

· REMOTE (RJ-45)

Connection for remote control of monitor.

· DVI-IN / FACTORY PGM

Input connection for DVI mode and input connector for FACTORY PGM allowing for

firmware updates.

· CVBS1/Y/G/S-Y (BNC)

Signal input terminal used for COMPOSITE1, S-VIDEO Y, COMPONENT Y, RGB G signals.

· CVSBS2/Pb/B (BNC)

Signal input terminal used for COMPOSITE2, RGB B, COMPONENT Pb signals.

· CVSBS3/Pr/R/S-C (BNC)

Signal input terminal used for COMPOSITE3, S-VIDEO C, COMPONENT Pr, RGB R signals.

· SDI-IN A (BNC)

SDI signal input terminal that provides A signal.

· SDI-OUT A (BNC)

SDI signal output terminal used for SDI A output.

· SDI-IN B (BNC)

SDI signal input terminal that provides B signal.

· SDI-OUT B (BNC)

SDI signal output terminal used for SDI B output.

· ~ AC IN

Used to supply AC power; 100V~240V input range.

· DC 24V IN

Used to supply DC power; 24V

LVM-170W (G) / 230W / 240W

Information

Input VIDEO connection method

GGGGG

Warning!!

Before using this unit make certain to connect the power supply before connecting a

signal to any of the inputs. The unit may not function properly if a signal is connected

before the power supply is connected. As an example: the unit will not function properly

when using an RCA-to-BNC (BNC-to-RCA) connection if the signal is connected to the

input before the unit is connected to the power supply.

Connector Composite Component S-Video

1CVBS1YG Y

CVBS2 Pb B

No Con.

3CVBS3PrRC

LVM-170W (G) / 230W / 240W

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali TV Logic Monitor

TV Logic

TV Logic R-5T Manuale utente

TV Logic

TV Logic SWM Series Manuale utente

TV Logic

TV Logic LVM-245W Manuale utente

TV Logic

TV Logic LEM-550R Manuale utente

TV Logic

TV Logic LVM-171WP Manuale utente

TV Logic

TV Logic VFM-056W Manuale utente

TV Logic

TV Logic LEM-250C Manuale utente

TV Logic

TV Logic LVM-071W Manuale utente

TV Logic

TV Logic LVM-173W-3G Manuale utente

TV Logic

TV Logic LVM-171W Manuale utente

TV Logic

TV Logic TSM-232W Manuale utente

TV Logic

TV Logic LVM-180A Manuale utente

TV Logic

TV Logic LVM-173W-3G Manuale utente

TV Logic

TV Logic LVM-174W Manuale utente

TV Logic

TV Logic F-7H Manuale utente

TV Logic

TV Logic F-5A-AG Manuale utente

TV Logic

TV Logic VFM-056W-N Manuale utente

TV Logic

TV Logic XVM-177A Manuale utente

TV Logic

TV Logic LVM-246W Manuale utente

TV Logic

TV Logic LUM-550M Manuale utente

TV Logic

TV Logic LVM-181S Manuale utente

TV Logic

TV Logic TDM-243W Manuale utente

TV Logic

TV Logic LVM-172W Manuale utente

TV Logic

TV Logic F-5A Manuale utente

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione