Tycon Power Systems TP-SW5G-NC Manuale utente
TYCON POWER SYSTEMS
TYCON TP-SW5G(-NC)
5 port PoE Endspan (Switch)
(Extend Ethernet and PoE)
User’s Manual
TYCON TP-SW5G(-NC) Series
TYCON POWER SYSTEMS
2
1. General Information..............................................................
2. Hardware Description...........................................................
LED Indicators.......................................................................................
Power Wiring ........................................................................................
Ethernet Port Wiring..............................................................................
PD Port Wiring......................................................................................
Network Application……………………………………............................
3. Model Information...........................................................
4. Technical Specification........................................................
3
3
3
5
8
10
11
12
13
User’s Manual
TYCON TP-SW5G(-NC) Series
TYCON POWER SYSTEMS
3
1. General Information
The PoE (Power Over Ethernet) Switch family provide four 10M/100M/1000M TX ports with PoE
TP-SW5G function plus one 10M/100M/1000M TX up-link port with PoE PD function. It allows power
souring equipment (PSE) to be powered from PoE and deliver power to PoE powered device (PD), which
are compliant with IEEE802.3af and IEEE802.3at standard to receiver and deliver both Ethernet data and
DC power through the traditional UTP or STP cable. The PoE Switch can extend Ethernet data and DC
power up to 200 meters.
This manual will help you install and maintain the PoE switch. Installation of the
PoE switch is very easy and you can start to use the product as soon as you are powered up.
2. Hardware Description
*LED Indicator
There are 12 LEDs on the PoE switch to indicate the status of power and signal. The following section
describes the functions of each LED indicator.
Front panel detail
User’s Manual
TYCON TP-SW5G(-NC) Series
TYCON POWER SYSTEMS
4
*POWER LED
LED
STATUS
Description
Power
Green
LED ON when power input (DC IN on
rear panel or Port 5 on front panel) has
valid power supplied.
Red
The indicator is only used on
TP-SW5G-NC, LED ON when the
following warning condition happens.
*Power input under voltage (Vin<10V)
*Power input over voltage (Vin>59V)
*PoE over current (2A/per port)
the indicator is unused on
TP-SW5G/TP-SW5G24
Off No power supplied.
*SWITCH LED (the right indicator on RJ45)
LED STATUS Description
P1~P5
Link/Act
Green
A network device is detected (1000Mbps),
but no communication activity is detected.
Green
Blinking
This port is transmitting to, or receiving
package from another device at 1000Mbps.
Yellow A network device is detected (10Mbps or
100Mbps), but no communication activity
is detected.
Yellow
Blinking
This port is transmitting to, or receiving
package from another device at 10Mbps or
100Mbps.
Off No device is detected.
User’s Manual
TYCON TP-SW5G(-NC) Series
TYCON POWER SYSTEMS
5
*PoE LED (the left indicator on RJ45)
P1~P4
PoE
Yellow
A valid Powered Device (PD) is detected
and delivering power on this port.
Off
No PD is detected on this port.
P5
PoE
Yellow
Powered via all 4 data pairs.
Yellow
Blanking
Powered via 2 data pairs. (1,2,3,6 or 4,5,7,8
are all acceptable).
Off No power is detected on this port.
*Power wiring
The PoE switch family includes 3 models, be used for 3 different ranges of input voltage:
full range voltage (12 to 57VDC) (P/N: TP-SW5G-NC)
24VDC typical (12 to 36VDC) (P/N: TP-SW5G24)
48VDC typical (40 to 57VDC) (P/N: TP-SW5G)
All of the PoE switches allow power by another PoE source (42.5~57VDC) on port 5 (UPLINK).
For PoE operation, make sure your power supply may offer at least 75W for 4x 802.3af PoE port, or 150W
for 4x 802.3at PoE port.
If powered via the rear terminal, please make sure the input current is not over 10A. If powered on port 5,
make sure the input current is not over 2Amp.
Ports 1~4 will deliver DC power over the Ethernet cable as detailed below:
* Data pair A on line 1 and 2
* Data pair B on line 3 and 6
* Data pair C plus V+ on line 4 and 5
* Data pair D plus V- on line 7 and 8
User’s Manual
TYCON TP-SW5G(-NC) Series
TYCON POWER SYSTEMS
6
Port 5 may get DC power over the Ethernet cable, as detailed below:
* Data pair A plus V+ /V- on line 1 and 2
* Data pair B plus V-/V+ on line 3 and 6
* Data pair C plus V+/V- on line 4 and 5
* Data pair D plus V-/V+ on line 7 and 8
The terminal block on the rear panel should be wired as detailed below:
*For TP-SW5G24
Please note that the maximum power per port of 35W can only be achieved using 24VDC input operation. If
your input is 12VDC then the total power per port should be de-rated to 22W per port
*For TP-SW5G
The input voltage must be in the range of 44 to 57VDC if running for 802.3af operation.
The input voltage must be in the range of 50 to 57VDC if running for 802.3at operation.
If the TP-SW5G is not powered with the above designated input voltage, it will only function as an Ethernet
switch without PoE output.
User’s Manual
TYCON TP-SW5G(-NC) Series
TYCON POWER SYSTEMS
7
Model Input Voltage
(REAR) Input Voltage
(Port 5) Output voltage 802.3af/at
Isolated
TP-SW5G-NC
12-57VDC No input
12-57VDC
(As input voltage)
(non-regulated) No No
No input 42.5-57VDC 42.5-57VDC
(non-regulated) No No
12-57VDC 42.5-57VDC
Higher voltage
output
(REAR or Port 5)
No No
T
P-SW5G24
12-36VDC No input 56VDC
(regulated) Yes No
No input 42.5-57VDC 42.5-57VDC
(non-regulated) Yes No
12-36VDC 42.5-57VDC 56VDC
(regulated) Yes No
TP-SW5G
40-57VDC No input 40-57VDC
(non-regulated) Yes No
No input 42.5-57VDC 42.5-57VDC
(non-regulated) Yes No
40-57VDC 42.5-57VDC
Higher voltage
output
(REAR or Port5)
Yes No
You can use the TP-SW5G(NC) series with our adaptor products as detailed below: (OPTION)
PSHP-18 PSHP-24 PSHP-48
Maximum output 18VDC/7.5A 24VDC/6.25A 48VDC/3.125A
Related model TP-SW5G-NC
TP-SW5G24
TP-SW5G-NC
TP-SW5G24
TP-SW5G-NC
TP-SW5G
User’s Manual
TYCON TP-SW5G(-NC) Series
TYCON POWER SYSTEMS
8
*Ethernet Port Wiring
The PoE switch family supports one RJ-45 uplink (port 5 with PoE PD) and four RJ-45 ports (port 1~4 with
PoE TP-SW5G(-NC) with automatic MDI/MDI-X crossover, auto-sense for speed and duplex for 10Base-T,
100Base-TX or 1000Base-T connection. Automatic MDI/MDI-X crossover allows you to connect to other
devices (switches, hubs, or workstations etc.), without regard to using straight-through or crossover cabling.
Port 1 to 4 provides Power over Ethernet function that delivers DC power through the data pairs C & D (pair
4,5 and pair7,8) to the PD. Port 5 provides Power Device function that receive power from 4 pairs or 2 pairs
Ethernet cable.
The following tables describe the wiring diagram of straight-through and crossover cabling. The crossover
cables simply cross-connect the transmit lines at each end to the receive lines at the opposite end.
Straight-through Cabling
Pin 1
Pin 1
Pin 2
Pin 2
Pin 3
Pin 3
Pin 6
Pin 6
Pin 4
Pin 4
Pin 5
Pin 5
Pin 7
Pin 7
Pin 8
Pin 8
User’s Manual
TYCON TP-SW5G(-NC) Series
TYCON POWER SYSTEMS
9
Cross-over Cabling
Pin 1
Pin 3
Pin 2
Pin 6
Pin 3
Pin 1
Pin 6
Pin 2
Pin 4
Pin 7
Pin 5
Pin 8
Pin 7
Pin 4
Pin 8
Pin 8
Connect an Ethernet cable into any switch port and connect the other side to your
attached device. The Link/Act LED (green or yellow) will light up when the cable is correctly connected.
Refer to the LED Indicator section for descriptions of each LED indicator.
If a port LED is off, go back and check for connectivity problems between that port and the network device
connected.
The maximum cable length for 10/100/1000BaseT with Cat 5 twisted pair cables is typically 100m (328 ft.).
User’s Manual
TYCON TP-SW5G(-NC) Series
TYCON POWER SYSTEMS
10
*PD Port Wiring
Port 1 to 4 provides PoE injection function with maximum 35W ability to power up the powered device
using the straight-through or cross-over Ethernet cable.
The PoE switch follows the IEEE802.3af Alternative B mode connector assignment. The following table
shows pin assignment of alternative A and B for the Power Source Equipment.
Conductor Alternative A
(MDI-X) Alternative A
(MDI) Alternative B
(All)
1Negative Vport Positive Vport
2 Negative Vport Positive Vport
3 Positive Vport Negative port
4 Positive Vport
5 Positive Vport
6 Positive Vport NegativeVport
7 Negative Vport
8 Negative Vport
Be sure the twisted pair cable is bound with the standard RJ-45 pin, especially the pins 4, 5, 7 and 8. If the
RJ-45 is bound with the wrong pin number, the PoE switch will not recognize the PD and won’t deliver DC
power to the PD. The yellow PoE LED will light up when the cable is correctly connected. Refer to the LED
Indicator section for descriptions of each LED indicator. If a port LED is off, go back and check for
connectivity problems between that port and the network device connected.
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali Tycon Power Systems Interruttore
Tycon Power Systems
Tycon Power Systems TP-SSW5(-NC) Manuale utente
Tycon Power Systems
Tycon Power Systems TP-SW5GNC-OUT Manuale utente
Tycon Power Systems
Tycon Power Systems TP-SW5G Manuale utente
Tycon Power Systems
Tycon Power Systems TP-SW8GAT/24-SFP Manuale utente
Tycon Power Systems
Tycon Power Systems TP-SW5G-MULTI Manuale utente
Tycon Power Systems
Tycon Power Systems TP-MS4x4 Manuale utente
Tycon Power Systems
Tycon Power Systems TP-SW8(-NC) Manuale utente
