U-Line H-1024 Manuale utente

0812 IH-1024PAGE 1 OF 7

H-1024, H-1025

H-1026

MANUAL

CARTON STAPLER

STAPLER SPECIFICATIONS

Dimensions (L x H x W) 15 x11½ x 4½"

Weight (Without Fasteners) 3.75 lb.

H-1025/H-1026 Staple Specification S-289 C58 Stick and/or S-1396 C34 Stick

H-1024 Staple Specification S-1397 A58 Stick

Staple Capacity 100 Staples

Before operating this stapler familiarize yourself with the safety warnings and

instructions in this manual. Keep these instructions with the stapler for future

reference. If you have any questions, contact Uline at 1-800-295-5510.

WARNING

0812 IH-1024PAGE 2 OF 7

SAFETY INSTRUCTIONS

1. Read the manual and understand all safety

instructions before operating the stapler. If you have

questions, contact Uline at 1-800-295-5510.

2. Always wear protective equipment; e.g., safety

glasses, hearing protection and head protection.

3. Do not place your hand or any other body part in

the staple clinching area.

4. Never point the stapler at yourself or anyone else.

LOADING THE STAPLER

1. Pull the pusher back until it stops on pusher pivots.

Rotate pusher to position. (See Figure 1)

2. Insert up to 2 sticks of appropriate staples into the

magazine. Let the sticks slide forward to the front of

the magazine. (See Figure 2)

3. Pull the pusher back to an upright position and

gently let the pusher slide forward against the

staples. Do not let the pusher slide forward and

strike the staples at high speed as this may deform

the staples and damage the stapler.

ADJUSTING STAPLE LEG LENGTH

1. Loosen the set screw with a 3mm Allen wrench on

the bottom. (See Figure 3)

2. Turn adjusting rod 180º with a screw driver to the

desired setting.

3. If you are using ¾" staples set L up.

4. If you are using 5⁄8" staples set S up. (See Figure 4)

5. Tighten the set screw.

Figure 1 Figure 2

Figure 3 Figure 4

0812 IH-1024PAGE 3 OF 7

SAFETY INSTRUCTIONS (CONTINUED)

CLINCH ADJUSTMENT

Loosen securing nut closest to body. Turn adjustment

nut clockwise to loosen clinch. Turn adjustment nut

counter-clockwise to tighten clinch. After adjusting,

tighten securing nut. (See Figure 5)

Figure 5

DEPTH ADJUSTMENT

1. Loosen front 2 screws with a 4mm Allen w rench.

(See Figure 6)

2. Push the body up and adjust to the desired depth.

(See Figure 7)

Figure 7

Figure 6

0812 IH-1024PAGE 4 OF 7

OPERATING INSTRUCTIONS

1. Protect your eyes and ears.

a. Wear safety glasses with side shields.

b. Wear hearing protection.

c. Ensure that anyone in the vicinity wears safety protection.

2. To prevent accidental injuries, never place a hand or any other body part in

the staple clinching area or adjustment window.

3. Never point the stapler towards you or anyone else.

4. Always handle the stapler with care. Never pull the trigger unless stapler is

ready for operation.

5. Check and replace any damaged or worn components on the stapler.

BASIC OPERATION

1. Insert the staples into the stapler following the

loading instructions.

2. Grasp the handle with one hand on box in line

with the desired staple location. There is a small

projection on either side of the magazine seat as an

aid in locating the position of the staple.

3. For strongest closure, use staples close to the ends

of the box.

CLEARING A JAM

1. Pull pusher back and rotate to a locked position.

(See Figure 8)

2. Insert needle nose pliers or screw driver to clear jam.

(See Figure 9)

3. Slowly release pusher back to position.

Figure 8 Figure 9

WARNING

0812 IH-1024PAGE 5 OF 7

TROUBLE SHOOTING

PROBLEM CAUSE REMEDY

Excessive jams Teeth screws are loose or

staples are wrong size.

Tighten screws and check staples.

Uneven clinch Wrong staple size. Check for proper leg length adjustment and

clincher size.

Unclinched staple Teeth are loose or broken. Check and replace teeth as needed.

Stop using the stapler immediately if any of the following problems occur.

Serious personal injury could occur. Any repairs or replacements must be

done by a qualified person or authorized service center only.

WARNING

TEETH REPLACEMENT

1. Loosen screws and nut with an 8 mm wrench and

4mm Allen wrench. (See Figure 10)

2. Remove the magazine assembly. (See Figure 11)

Figure 10 Fi gu re 11 Figure 12

3. Loosen screws with 3 mm Allen wrench.

(See Figure 12)

4. Change teeth one at a time to prevent reverse teeth.

0812 IH-1024PAGE 6 OF 7

DRIVER REPLACEMENT

1. Loosen screw and nut with a 8 mm spanner wrench

and a 4mm Allen wrench. (See Figure 13)

2. Remove the magazine assembly. (See Figure 14)

3. Loosen the set screw with a 3mm Allen wrench to

unlock the adjusting rod. (See Figure 15)

4. Remove the linkage mechanism and adjusting rod

simultaneously from the body.

TROUBLE SHOOTING (CONTINUED)

5. Loosen the pivot screws with flat screwdriver.

Remove handle and linkage mechanism.

6. Remove the spring pin with a hammer and 5 mm

straight rod.

7. Loosen screws with a 3mm Allen wrench. Take off

the spring pin with a hammer and 6 mm straight rod.

(See Figure 16)

Figure 13

Figure 15

Figure 14

Figure 16

0812 IH-1024PAGE 7 OF 7

PUSHER SPRING REPLACEMENT

1. Loosen the screws and nut with a 8mm spanner

wrench and a 4 mm Allen wrench. (See Figure 17)

2. Remove the magazine assembly. (See Figure 18)

3. Pull the pusher back until it stops on the rod, rotate

the pusher to position.

4. Push the magazine seat back and remove it from

the magazine.

5. Loosen the screw and nut with a 2.5mm Allen

wrench and 7mm socket wrench. (See Figure 19)

6. Loosen the rod with a 6mm offset wrench and

remove the pusher guides. Remove the pusher.

(See Figure 20)

7. Remove the spring pin with a hammer and 4 mm

straight rod. (See Figure 21)

TROUBLE SHOOTING (CONTINUED)

π CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA

1-80 0-295 -5510

uline.com

Fig ure 17 Figure 18 Figure 19

Figure 20 Figure 21

Altri manuali per H-1024

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali U-Line Utensili elettrici

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale