U-Line H-1028 Manuale utente
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
AIR DRIVE CARTON STAPLER
MODEL: H-1028
MANUAL
WARNING
Before operating this stapler familiarize yourself with the safety warnings and
instructions in this manual. Keep these instructions with the stapler for future
reference. If you have any questions, contact Uline at 1-800-295-5510.
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
Table of Contents
Tool Specifications
Safety Instructions
Lubrication & Maintenance
Air Supply & Connections
Loading the Tool
Checking the Staple Leg Length
Clinch Adjustment
Depth Adjustment
Tool Operation
Cleaning the tool
Clearing Tool Jams
Troubleshooting
Teeth Replacement
Driver Replacement
Pusher Spring Replacement
Valve & Tube O-Ring Replacement
Piston Replacement
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
Tool Specifications
Model of Tool H-1028
ADB 18-32
Dimensions: LxHxW 13.5x8.75x6
Weight (without Fasteners) 6lbs
Compressed Air:
Maximum PSI: 110 psi
Recommended Operating Pressure: 71-100 PSI
Air Consumption:
Staple Specification: S-1396 C34 Stick
Staple Specification: S-289 C58 Stick
Staple Capacity: 100 staples
Noise Levels:
Back to Top
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
SAFETY INSTRUCTIONS
1. Read the manual and understand all safety instructions before operating the
tool. If you have questions, contact Uline at 1-800-295-5510.
2. Never use flammable gases as a power source for the stapler. Only use
filtered, compressed air.
3. Never use gasoline or other flammable liquids to clean the stapler. Vapors
left on the stapler could ignite and cause the tool to explode
4. Do not exceed 110 psi of air pressure when operating the stapler.
5. Disconnect the stapler for the air supply before making adjustments,
cleaning or clearing jams and when not in use.
6. Do not pull the trigger when carrying or holding the stapler.
7. Never carry the stapler by the hose or pull on the hose to move the stapler.
8. Always wear protective equipment, i.e. safety glasses, hearing protection
and head protection.
9. Do not use a check valve or any other fitting which allows air to remain in the
stapler.
10.Do not place your hand or any other body part in the staple clinching area or
adjustment window when connecting or disconnecting the air supply.
11.Never point the stapler at yourself or anyone else.
Back to Top
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
Lubrication & Maintenance:
1. Lubricate the stapler prior to initial operation.
2. Disconnect the stapler from the air supply prior to servicing.
3. Turn the stapler so that the inlet is facing up and put one drop of high-speed
spindle oil, UNOCOL RX22, or 3-in-1 oil into air inlet. Never use detergent
oil or additives.
4. Operate the tool briefly after adding oil.
5. Wipe off excessive oil at the exhaust. Excessive oil will damage the O-rings.
If inline oiler is used, manual lubrication through the air inlet is not required
on a daily basis.
Back to Top
Air supply and Connections
NOTE:
The following illustration shows the correct mode of connection to the air supply
system which will increase the efficiency and life of the stapler.
Many air tool users find it convenient to use an inline oiler to provide oil circulation
through their tool. Check oil level in the oiler daily.
A filter is recommended on your air compressor. Check the filter and drain on a
daily basis.
Back to Top
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
Loading the Tool
1. Disconnect the air supply.
2. Pull the Pusher back until it stops on pusher pivots. Rotate pusher to
position.
3. Insert 2 sticks of appropriate staples into the magazine. Let the sticks slide
forward to the front of the magazine.
4. Pull the pusher back to an upright position and gently let the pusher slide
forward against the staples. Do not let the pusher slide forward and strike
the staples at high speed as this may deform the staples and damage the
tool.
Back to Top
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
Staple Leg Length
1. Loosen the set screw with a 3mm Allen wrench.
2. Adjust 180°with a screw driver to the desired setting.
3. If you are using ¾” staples set L up.
4. If you are using 5/8” staples set S up. (diagram)
5. Tighten the set screw.
Back to Top
Clinch Adjustment
Use 2.5 mm Allen wrench and turn collar through window clockwise to tighten
clinch.
Back to Top
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
Depth Adjustment
1. Loosen front screw with a 6mm Allen wrench.
2. Push the body up and adjust to the desired depth.
3. When the top edge of the adjustment plate is at it’s highest setting the teeth
are at their shallowest penetration. If set at No. 1 the teeth are at their
deepest penetration.
Back to Top
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
Operating Instructions
Warning
1. Add a few drops of oil into the air inlet.
2. Install a quick connect fitting to the tool.
3. Regulate the air pressure to attain 80-100 psi.
4. Insert the staples into the tool following the loading instructions.
5. Reconnect the air hose to the tool.
6. Grasp the handle with one hand on box in line with the desired staple
location. There is a small projection on either side of the magazine seat as
an aid in locating the position of the staple.
7. The strongest closure requires staples close to the ends of the box.
Back to Top
Cleaning the Tool
Danger
1. Disconnect the Air Supply from the tool
2. Remove tar buildup with non-corrosive cleaner. Do not allow solvent to get
into the cylinder or damage may occur.
3. Dry the tool completely before use.
Back to Top
Never use gasoline or other flammable liquids to clean the stapler.
Vapors in the stapler could be ignited by a spark and cause the tool to explode.
1. Protect your eyes and ears. Wear:
a. Safety glasses with side shields
b. hearing protection.
Ensure that anyone in the vicinity wears safety protection.
2. To prevent accidental injuries never place a hand or any other body part in the staple
clinching area or adjustment window.
3. Never point the stapler towards you or anyone else.
4. Always handle the stapler with care. Never pull the trigger unless tool is ready for
operation.
5. Check and replace any damaged or worn components on the stapler.
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
PHONE 1-800-295-5510 FAX 1-800-295-5571 WEB uline.com
Clearing a Jam
1. Disconnect Air Supply
2. Pull Pusher back and rotate to a locked position.
3. Insert needle nose pliers or screw driver to clear jam.
4. Slowly release Pusher back to position.
Back to Top
CHICAGO •MINNEAPOLIS •LOS ANGELES •NYC/PHILA •ATLANTA •DALLAS
Indice
Altri manuali U-Line Utensili elettrici
U-Line
U-Line H-1024 Manuale utente
U-Line
U-Line Swingline Light Touch H-2323 Manuale di istruzioni
U-Line
U-Line RIPACK 3000 Manuale utente
U-Line
U-Line SHRINKFAST 998 Manuale utente
U-Line
U-Line H-915 Manuale utente
U-Line
U-Line SHRINKFAST H-6098 Manuale utente
U-Line
U-Line H-1980 Manuale utente
U-Line
U-Line H-3070 Manuale utente
U-Line
U-Line Shrinkfast 975 Manuale utente
U-Line
U-Line H-8094 Manuale utente
U-Line
U-Line H-1030 Manuale utente
U-Line
U-Line H-491 Manuale utente
U-Line
U-Line SWINGLINE H-3067 Manuale utente
U-Line
U-Line H-1026 Manuale utente
U-Line
U-Line H-2027 Manuale utente
U-Line
U-Line H-1302 Manuale utente
U-Line
U-Line H-10157 Manuale utente
U-Line
U-Line H-2028 Manuale utente
U-Line
U-Line H-1481 Manuale utente
U-Line
U-Line H-3070 Manuale utente
