U.S. Products Agitator 20 Istruzioni operative

DO NOT OPERATE THE MACHINE UNTIL YOU HAVE READ

ALL SECTIONS OF THESE INSTRUCTIONS

IMPROPER USE OF THE MACHINE WILL VOID THE WARRANTY

1. Always use a defoamer when foaming occurs to prevent vacuum motor damage.

2. Never use water with a temperature above

130 °F / 54 °C in the machine.

3. Keep machine from rain and snow, avoid extremes in temperatures, and store

in a heated location. Use the machine indoors only.

4. Use approved chemicals only. NO SOLVENTS.

5. Wear gloves or use rags when removing quick disconnects to prevent burns.

6. Never leave the machine plugged in when you are not attending it.

AGITATOR 20®

120V

INFORMATION

OPERATING

INSTRUCTIONS

06.04.2007

Record the serial number and model of your new extractor here:

(and be sure to mail your warranty card)

Serial Number: __________________ Model: AGITATOR-20 Purchase Date:_____________

Write the name and phone number of your distributor:

UNPACKING:

Carefully unpack and inspect your Agitator-20 for shipping damage. Each machine is tested and

inspected before shipping. Any shipping damage incurred is the responsibility of the carrier. You

should notify the carrier immediately if you notice damage to the box or to the machine or parts.

CLEANING SOLUTIONS:

We recommend a neutral pH, low foam cleaner, applied to the carpet as a pre-spray.

MAINTENANCE:

After each job, rinse the recovery tank and dump hose with clear water. Clean both filters after each

job. Lubricate the wheels and quick disconnects with an all purpose silicone spray, as needed. The

vacuum motor may require new brushes after 1000 - 1500 hours. An impeller replacement kit for

the dump pump is enclosed with these instructions: use the replacement kit when the dump pump

performance falters. Clean the body with an all purpose detergent, and protect it with an automobile

interior spray protectant.

DO NOT OPERATE THE MACHINE UNTIL YOU HAVE READ THIS SECTION.

IMPROPER USE MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE.

IMPROPER USE WILL VOID THE WARRANTY.

yAlways use a defoamer when foaming occurs to prevent vacuum motor damage.

yNever use water above 130 °F (54 °C).

yDo not store outdoors. Avoid extremes in temperature.

yUse approved chemicals only. All chemicals should be mixed thoroughly. A pH between 6 and 9

is recommended. The use of high alkaline detergents or strong acids will accelerate the wear of

the seals, and will void the warranty.

yCarpet cleaning chemicals may affect bare floor finishes. Take precaution to keep chemicals

from surfaces other than the carpet.

yAll cords must have a rating of at least 12/3 (#12 cord). Replace the plug immediately if the

ground prong becomes damaged or is broken off.

yWear clean tennis shoes or non-slip shoes when working with a carpet extractor. Street shoes or

rubber sole shoes will release absorbed dirt or grease, when wet, onto the carpet.

yWet shoes can be a slipping hazard on bare floors -- be sure to dry your shoes before walking

onto bare floors.

IMPORTANT SAFETY INSTRUCTIONS

This machine is only suitable for commercial use, for example in hotels, schools, hospitals, factories,

shops and offices other than normal residential housekeeping purposes.

When using any electrical appliance, basic precautions should always be followed, including the

following:

Read all instructions before using this appliance.

WARNING!

To reduce the risk of fire, electric shock, or injury:

•Do not leave the machine when it is plugged in. Unplug the unit from the outlet when not in use

and before servicing.

•To avoid electric shock, do not expose to water/snow. Store and use indoors.

•Use only as described in this manual. Use only the manufacturer’s recommended attachments.

•Do not use with damaged cord or plug. If the machine is not working as it should be, has been

dropped, damaged, left outdoors or dropped into water, return it to a service center.

•Do not pull or carry by the cord, use the cord as a handle, close a door on the cord, or pull the

cord around sharp edges or corners. Do not run the appliance over the cord. Keep the cord

away from heated surfaces.

•Do not unplug by pulling on the cord. To unplug, grasp the plug, not the cord.

•Do not handle the plug, cord or machine with wet hands.

•Do not put any object into openings. Do not use with any opening blocked; keep free of dust,

lint, hair, and anything that may reduce air flow.

•Keep loose clothing, hair, fingers, and all parts of body away from openings and moving parts.

•Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes, or

any health endangering dusts.

•Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where

they may be present.

•Turn off all controls before unplugging.

•Use extra care when cleaning on stairs.

•Connect to a properly grounded outlet only. See Grounding Instructions.

•Liquid ejected at the spray nozzle could be dangerous as a result of its temperature, pressure or

chemical content.

SAVE THESE INSTRUCTIONS

120VAC GROUNDING INSTRUCTIONS

This machine must be grounded. If it should electrically malfunction, grounding provides a path of least

resistance for electric current to reduce the risk of electric shock. This machine is equipped with a cord

having an equipment-grounding conductor and grounding plug. The plug must be plugged into an

appropriate outlet that is properly installed and grounded in accordance with all local codes and

ordinances.

DANGER!

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check

with a qualified electrician or service person if you are in doubt as to whether the outlet is properly

grounded. Do not modify the plug provided with the machine. If it will not fit the outlet, have a proper

outlet installed by a qualified electrician.

This machine is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug

illustrated in Figure 1 below. A temporary adapter illustrated in Figures 2 and 3 may be used to connect

this plug to a 2-pole receptacle as shown in Figure 2 if a properly grounded outlet is not available. The

temporary adapter should be used only until a properly grounded outlet (Figure 1) can be installed by a

qualified electrician. The green-colored rigid ear or tab extending from the adapter must be connected to

a permanent ground such as a properly grounded outlet box cover. Whenever the adapter is used, it must

be held in place by a metal screw. Grounding adapters are not approved for use in Canada.

Replace the plug if the grounding pin is damaged or broken.

The Green (or Green/Yellow) wire in the cord is the grounding wire. When replacing a plug, this wire

must be attached to the grounding pin only.

Extension cords connected to this machine should be 12 gauge, three-wire cords with three-prong plugs

and outlets. DO NOT use extension cords more than 50 feet (15 m) long.

PLEASE NOTE: FOR NORTH AMERICA ONLY

Power

On / Off

Switch

AGITATOR 20, 120V

Switch and Indicator Light Operation

The Power ON/OFF switch on the front panel

will supply power to all the systems, however,

only the vacuum will turn on automatically

with this switch.

The Push Button on top of the back of the

handle will activate the Agitator bar and the

Spray. This button is positioned for ease of

use when operating the machine.

The Dump Pump will turn on and off during

use as the sensor in the Recovery Tank detects

the level of water.

A sensor in the Recovery Tank will detect

foam, when present, and activate a solenoid to

allow defoamer to flow into the tank.

The indicator lights on the panel will turn on

when the associated function is operating.

Indicator

Lights

Vacuum Shoe

Switch and

Indicator

Panel

Latch,

cover

Clear-vue

cover Defoamer

Tank

Lid

4”

Wheel

Fan

Recovery

Tank,

Filters

Push

Button

Inlet

Water Hose

Recovery

Water Hose

Receptacle,

power cord

“D” Connector

and Swivel

Snap-Hook

1Always use a vacuum cleaner on the carpet in the treatment area before using the Agitator-20.

2Pre-treat spots, stains and heavy traffic areas before extraction. Consult your local distributor for

procedures and/or chemical advice.

NOTE: the Agitator-20. is intended to provide a clear water rinse and dirt extraction after

application of a pre-spray; however, a chemical injection system is available, as an option, to add

cleaning detergent to the Agitator-20’s solution line.

3Set up the hoses: Unscrew the aerator from the sink faucet, if applicable, and screw the adaptor

hose onto the threads on the faucet. Join the solution hose to the adaptor hose by connecting the

quick disconnects. Place the drain hose securely into the sink drain.

4Lay the hoses out, from the sink to the Agitator-20. Attach both the water supply hose and the

drain hose to the machine.

5Make sure there is defoamer in the defoamer bottle, if foam is present.

6Turn on the water supply. Be sure not to use water above 130 °F.

7Plug the power cord from the Agitator-20. into a wall outlet. Use a GFCI protected outlet if possible.

8Turn on the main power switch.

NOTE: It is best to clean around the perimeter of the room at first, so you can get as close to the

baseboard as possible. Use the right side of the machine against the wall for the best results.

After the perimeter has been cleaned, start cleaning on one side of the room, and work your way

across the room in over-lapping rows.

9When cleaning with the Agitator-20. tilt the front of the machine up and off the carpet by pushing

down on the handle, and move the machine forward across the carpet. Let the front of the machine

down and pull backwards as you activate the spray and the agitator button. Let off the spray

button about 12” before the end of the row so that the machine can recover all the spray that was

put down. Let off the agitator button when you reach the end of the row. Tilt the front of the

machine up and move the machine towards the top of the next row. Continue this way until the

whole room or the entire area has been cleaned.

10 At the end of each job, follow these instructions to rinse out the recovery tank and hoses:

move the machine near the sink. Leave it plugged in. Turn off the water faucet. Disconnect the

solution hose from the faucet and set the end of the hose in the sink. Fill a bucket with water, open

the lid to the recovery tank, and pour the water into the tank. Turn the dump pump on to send the

rinse water and residual dirt through the dump hose and into the sink. Repeat until clean.

When the rinsing is complete, leave the machine’s main power switch on just long enough to pump

all the water out of the machine and the hose. Turn off the main power switch, and unplug the

power cord.

Remove both the fabric pre-filter and the wire mesh filter, after each job, to clean and dry them.

Reinstall the filters after cleaning.

Disconnect the dump hose from the machine, and remove the adaptor from the faucet. Leave it

laying in the sink. Reinstall the aerator onto the faucet, if it had been removed. From the machine

end, coil up the hoses so any water remaining in them drains into the sink. Free the dump hose

from the sink drain. Wipe down the hoses and the machine.

OPERATION

ITEM PARTNo. DESCRIPTION

1 AG2-BLK Cover, component bay

2 1392 Stud, foam sensor

3 AG3-BLK Vacuum nozzle

4 1387 Knob, access door

5 1408 Screw, plastic, 6-32 X 1/4”

6 233 Washer, nylon

7 5 Bolt, 1/4-20 X 3/4”

7A 1033 Washer, flat

7B 218 Washer, rubber

8 FP428 Lid, vacuum chamber, complete

11 FP429 Inset, clear, for vac lid

11A 1231 Gasket, foam

13 1209 Plate, vacuum inlet filter mounting

14 1154 Adaptor, ABS, 1-1/2”

15 720 Vacuum hose,

16 1398 Filter, vac inlet, open cell

17 1416A Knob, 8-32, threaded

18 1399 Cover, filter for vac inlet

19 Switch plate assembly, complete

20 AG-BLK Body, AG-20, black

21 1196 Switch, push button, ON/OFF

22 1394A Snaphook, with swivel

23 1394 “D” Connector and Bracket

24 1453A Recepticle, AC power cord

25 AG1-BLK QD Bay, black

26 1309 Hose, recovery water out. 6”

26A TA30A Hose, recovery water out, 18”

27 1375 QD, male, 1/8 fmt

28 1376 Hose, fresh water in. 30”

29 1230 QD, male, 3/8 mpt

30 1426 Hose Barb, brass, 5/16’ hose X 1/8 mpt

32 1427 Hose Barb / Elbow, 3/8 hose X 3/8 fpt

33 385 Hose Clamp

36 3024 Wheel, 4”

37 27 Axle cap

38 910 Axle, cut to 21 “

40 FP431 Motor, agitator drive

41 1191 Pulley,primary

42 AG5-BLK Cover, belt and pulleys

43 1193 Belt, V-groove

44 1191 Pulley, secondary

45 1417 Bracket, motor support, drive motor

47 FP426 Agitator Assembly, complete

48 1212 Vacuum shoe, complete, S/S

AGITATOR-20

PART LIST

120V

ITEM PARTNo. DESCRIPTION

49 FP423 Spray bar assembly, complete

50 1371 Spray tip, 11004 V jet

52 FP434 Solenoid assembly, complete

54 FP432 Capacitor assembly, agitator drive

55 FP430 Fan assembly, 120V, 200CFM

60 408B Vacuum, 3-stage, 120V

61 2013A Gasket, vacuum

62 1415 Bulkhead fitting, union

62A 1229 Washer, rubber seal

63 928B Louver, 3”, black

64 1208 Strainer, vac inlet, nylon mesh

65 1386 Hinge, vac tank lid

66 1180 Plate, vacuum & pump mount

68 FP425 Filter Screen and housing

69 108A Hose barb, 3/8 pipe & hose

70 FP427 Pump, dump out, with fittings

72 1395 Defoamer bottle **

73 1396A Cap, defoamer bottle **

74 1396B Gasket, defoamer cap **

79 1389 Bezel, vac tank pass-through

81 1390 Gasket, bezel

MISCELLANEOUS ASSEMBLIES/PARTS

**FP441 Defoamer bottle assy, complete

1217A Power Cord, 80 ft

AG-HOSE Hoses & cord assembly, complete, 80’

AG-HOSE-X Hoses & cord assembly, complete 80’ extension

FP424 Faucet Adaptor, complete

FP430 Cooling Fan Assembly

Oct. 2006

SPECIFICATIONS:

Rotomolded Body:

Loop Agitator:

Cleaning Path:

Hoses and Power Cord:

Defoamer System:

Vacuum Motor:

Water Flow:

Dump Pump:

Water Pressure:

Agitator Brush Motor:

Electrical:

Amps:

Transport:

Dimensions:

Weight:

Lifetime Warranty

Patented design

20 inches wide

80 feet

Automatic

3-stage, 137” of water lift

1 gpm

5.5 gpm

50 -80 psi, typically

1/10 HP

120V, 12/3

4”, non-marking wheels

32.5”H x 35”L x 20”W

45 lbs

AGITATOR-20

208-772-0573 •800-257-7982 •FAX: 208-772-0577

Coeur d’Alene, Idaho

VISIT US AT: http://www.usproducts.com

AGITATOR 20®

120V

NOTES:

Indice

Altri manuali U.S. Products Macchina per pavimenti

U.S. Products

U.S. Products AGITATOR 16 Manuale utente

U.S. Products

U.S. Products ADVANTAGE-400H Series Istruzioni operative

U.S. Products

U.S. Products PB111-120 Manuale utente

U.S. Products

U.S. Products KING COBRA 1200 PRO Istruzioni operative

U.S. Products

U.S. Products COBRA-300H Manuale utente

U.S. Products

U.S. Products KING COBRA 1200 PRO Manuale utente

U.S. Products

U.S. Products HYDRAPORT 1200 Manuale utente

U.S. Products

U.S. Products KING COBRA 310-CSA Manuale utente

U.S. Products

U.S. Products ADVANTAGE-400H Series Istruzioni operative

U.S. Products

U.S. Products COBRA-H Manuale utente

U.S. Products

U.S. Products KING COBRA 310 Istruzioni operative

U.S. Products

U.S. Products Kraken Neptune 500 Istruzioni operative

U.S. Products

U.S. Products SPOTTER Manuale utente

U.S. Products

U.S. Products PEX 500 Istruzioni operative

U.S. Products

U.S. Products KING COBRA 150 Istruzioni operative

U.S. Products

U.S. Products COBRA-300H Istruzioni operative

U.S. Products

U.S. Products HYDRAPORT 100SC Istruzioni operative

U.S. Products

U.S. Products 100-041-016 Manuale utente

U.S. Products

U.S. Products KING COBRA 300 Istruzioni operative

U.S. Products

U.S. Products King Cobra KC-500 Istruzioni operative

Manuali Macchina per pavimenti popolari di altre marche

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Manuale utente

Numatic

Numatic ET 4045 Manuale utente

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Manuale utente

Mytee

Mytee 8070 Mytee-Lite Manuale utente

Kärcher

Kärcher B 140 R Manuale utente

Triple S

Triple S Ace 26T1 Manuale utente

Nilfisk-Advance

Nilfisk-Advance SW 750 Manuale utente

Tornado

Tornado Marathon 2000 98190 Manuale

Windsor

Windsor ADMIRAL Admiral 8 Manuale utente

Numatic

Numatic TTB 1117/100 Manuale utente

Tennant

Tennant 8210D Manuale utente

Nobles

Nobles Frontier Manuale del prodotto

lavina

lavina 21-X Manuale utente

KENT

KENT Edge 28B Manuale utente

Tennant

Tennant 215 Manuale del prodotto

Windsor

Windsor BDP 51/2000C Manuale utente

CleanFreak

CleanFreak DURA-18HD Manuale utente

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Guida per l'amministratore