U.S. Solid JF-6000 Manuale utente
Specification
Voltage: AC110V/60HZ or AC220V/50HZ
Power: 5W
Maximum tape width: 8mm-80mm
Maximum diameter of Roll:Ø300mm Feeding
speed:150mm/s
Weight:5.5kg(Leader+Accessories)
Dimension:190（w）*140（H）*230（D)mm
Applied tape:adhesive tape,non-adhesive tape
AUTOMATIC TAPE DISPENSER
JF-6000For questions or concerns, e-mail [email protected], visit
www.ussolid.com, or call (800) 209-4177
Precautions
This manual should be made available to all users of this equipment. For best
results, and for maximum durability of the equipment, carefully read and follow
all instructions.
The tape dispenser includes sharp metal parts, please be careful when
using the product.
Do not damage the cables, such as processing the cable, bending the
cable, pulling and strapping the cable, placing heavy objects on the cable or
cutting with scissors.
Do not use the tape dispenser if cable or plug has damages, or the socket
outlet is loose. Once the cable is damaged, do not disassemble or replace it by
yourself, but return the tape dispenser to factory for after-sales service.
When stop using the tape dispenser, or repairing and inspecting the tape
dispenser, please pull out the power plug from the outlet first.
Do not touch the cable or socket with wet hands. When repairing or
storing, please avoid water or moisture,and place the tape dispenser where
children can not reach and well ventilated.
When the tape is rolled into the feed rollers, please turn off the power
switch(OFF) before removing the tape.
Trouble caused by users’ split or assembly, the tape dispenser will be not
guaranteed.
The upper & lower blade set is easily sticked by adhesive tape, which will
cause the cutting not so smoothly, please clean the blade set on time.
Coat the Blade set with some oil or lubricant can improve the life
effectively.
When the tape feeding is curly, rotate the reel adjustment keys in
clockwise direction or replace the reel.
When the AUTO Feed does not work, please check whether the sensor
part is clean or not .
Troubleshooting
1.Problem:The tape will not be released automatically
or the tape will be sluggish.
Solution: Induction is too high, use a Phillips
screwdriver to adjust the bottom plate induction,
and adjust it in the - direction about 1MM.
2.Problem: Continuously cut tape, or cut a piece and
then alarm.
Solution: Induction is too low, use a Phillips
screwdriver to adjust the bottom plate induction, and
adjust it in the + direction about 1MM.
3.Problem: Excessive indentation on the tape
Solution: Pressure is too large, adjust the knob on the
top of the machine to the S direction by half a turn to
one turn
4.Problem: Tape does not come out when cutting
Solution: Pressure is too small, adjust the knob on the
top of the machine to the H direction by half a turn to
one turn.
5.Problem: The tape does not come out smoothly or
the glue outlet is blocked with the tape
Solution: Replace the separating roller ring.
6.Problem: Tape does not cut completely
Solution:The blade is worn or the shrapnel pressure is
too small, replace the blade or adjust the shrapnel
pressure.
How to use the tape dispenser
1) Insert the plug into the socket, and turned the power switch to ON.
2) Lifting up the tape stand, and rotating tape, then use the tape guide to fix
tape .
3) After hearing an electronic sounds ,the manual mode LED display and
meanwhile LED light(I) flashes .
4) Paste the end of the tape to the center of roller, and press the top of tape
gently, then press button(F), LED(I) will light up and the tape will be sent out to
the discharge port. When the tape is going outside,LED(J) will light up.
5) When LED(J) light flashes, press the cutting button(G), the machine will cut
the end of tape beyond the blade.
6) Press button(C) one time, then (A)(manual) and (B) (automatic mode) lights
are all on, in this state (semi-automatic mode), user can set the length that
needs to be cut.
7) In order to set the required cutting length (20 mm to 999 mm is adjustable) ,
you can press button(E)and button (F) .
8) In the semi-automatic mode, remove the cut tape, press button (G)(cutting),
according to required cutting length, tape will be send out again and in cutting
standby state. Semi-automatic mode can be used in cutting weak adhesive and
non-adhesive tape. At this point, you have to press button (G) (cutting) once
again, then the cut tape can be sent out according to the set length.
9) In the semi-automatic mode, after press the button (C), LED(A) will be off,
LED (B) will be on, and the mode switches to automatic mode. In the automatic
mode, the sensor will send out tape according to the set length.
Panel Button Introduction
A) LED in manual mode
B) LED in automatic mode
C) Function Switch
*When power input,operating by manual
mode .
*When pressing the button, operating by
semi-automatic mode.
*Re-Pressing the button, operating by
Automatic mode.
D) Tape length display
*5-999mm. Cutting length can precisely reach
to mm .
E) Length lengthen button
*At manual mode, the button can reverse
the feeder roller .
*At semi-automatic or auto mode, the button
can lengthen the tape cutting length.
F) Length shorten button
*At manual mode, the button can feed the
tape.
*At semi-automatic or auto mode, the button
can shorten the tape cutting length .
G) Cutting button
*The button can cut the tape .
H) I) J) LED under working condition .
A B
C
D
E
F
G
H
I
J
TAPEDISPENSER
MANUAL AUTO
REW/UP
FEED/DOWN
CUT/SEMIAUTO
MM
M/A
Structure of Main Part
1. Feeding Gear 2. Driving gear 1 3. Motor gear (metal gear)
4. Driving gear 2 5. Driving gear 3 6. Pressure Knob
7. Tape Feeding Holder
8. Pusher Bar 9.Copper Pillar 10.Motor
11.Cutting Sensing Board
Replace the blade set
1. Remove the screws on
the upper part of the shell
2. Remove the screws
on side
3. Unplug the connection
terminal
Replace the upper & lower blade
Remove the screws on the back of
Auto Feed Unit
Replace the reel 3451267891011Parts Replacement
12.Cover Pillar 13.Fixed Nut 14.Cutting Gear 1 15.Cutting Gear 2
16.Cutting Gear 3 17. Induction Paddle 18. Spring 19. Cutting Cover
20.Driving Gear 4 23.Cutting Holder 24.Pressure Sheet 25.Upper blade 26.Fixed Sheet
27.Cutter Liner(Left)28.Spring Steel 29.Limiting block 30.Lower blade
21. Tape Roller Unit 22. Separating Roller Ring 22-1.Feed Roller Unit31.Cutter Liner(Right) 32.Auto Feed Unit 34.Button 35.PVC Panel
161718141213151920232624252829303127323334352222-121
Indice
Altri manuali U.S. Solid Distributore
