Ubiquiti EdgeRouter 4 Manuale utente

4-Port Gigabit Router

with 1 SFP Port

Model: ER-4

Introduction

Thank you for purchasing the Ubiquiti Networks®

EdgeRouter™. This Quick Start Guide is designed to guide you

through installation and also includes warranty terms.

Package Contents

EdgeRouter ER-4

Mounting Bracket

Bracket Screws

(Qty. 8)

Mounting

Screws (Qty. 4)

Cage Nuts

(Qty. 4)

Wall Mount

Screws (Qty. 2)

Wall Mount

Anchors (Qty. 2)

Rubber Feet

(Qty. 4)

4-PortGigabit Router

with1 SFP Port

Model:ER-4

Ground

Screw

Power Cord Quick Start

Guide

responsibility to follow local country regulations, including operation within legal frequency

channels, output power, indoor cabling requirements, and Dynamic Frequency Selection

(DFS) requirements.

Installation Requirements

• Phillips screwdriver (for rack- or wall-mounting)

• Standard-sized, 19" wide rack with a minimum of 1U height

available (for rack-mounting)

• For indoor applications, use Category 5 (or above) UTP

cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)

cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the

power supply.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit:

www.ubnt.com/toughcable

WARNING: To reduce the risk of fire or electric shock,

do not expose the EdgeRouter to rain or moisture.

Note: Although the cabling can be located outdoors,

the EdgeRouter itself should be housed inside a

protective enclosure.

Hardware Overview

Front Panel Ports

Console RJ45 (eth0-eth2) SFP (eth3)

USB

Interface Description

Console

RJ45 serial console port for Command

Line Interface (CLI) management. Use an

RJ45-to-DB9, serial console cable, also

known as a rollover cable, to connect the

Console port to your computer. (If your

computer does not have a DB9 port,

then you will also need a DB9 adapter.)

Then configure the following settings as

needed:

• Baud rate 115200

• Data bits 8

• Parity NONE

• Stop bits 1

• Flow control NONE

USB Reserved for future use.

RJ45

(eth0-eth2)

RJ45 ports support 10/100/1000 Ethernet

connections.

SFP

(eth3)

SFP port is hot-swappable and supports

Gigabit fiber SFP modules.

Front Panel Button

Reset

Button Description

Reset

There are two methods to reset the

EdgeRouter to factory defaults:

• Runtime reset (recommended) The

EdgeRouter should be running after

bootup is complete. Press and hold the

Reset button for about 10seconds until

the LED for port eth3 starts flashing and

then becomes solidly lit. After a few

seconds, the LED will turn off, and the

EdgeRouter will automatically reboot.

• Power-on reset Disconnect the Power

Cord from the Power Adapter. Press and

hold the Reset button while connecting

the power (refer to Connecting Power for

details). Keep holding the button until

the LED for port eth3 starts flashing and

then stops flashing after a few seconds.

Front Panel LEDs

SFP: Speed/Link/Act

RJ45: Speed/Link/Act

System

LED State Status

System

Blue Bootup in Progress

White Ready for Use

RJ45 (eth0-2)

Speed/

Link/Act

Off No Link

Amber Link Established at

10/100Mbps

Amber Flashing Link Activity at

10/100Mbps

Green Link Established at

1000Mbps

Green Flashing Link Activity at

1000Mbps

SFP (eth3)

Link/Act

Off No Link

Green Link Established at

1Gbps

Green Flashing Link Activity at 1Gbps

*640-00303-02*

640-00303-02

Back Panel

Ventilation Holes Power Grounding Point

Note: There are additional ventilation holes on the sides

of the EdgeRouter.

Hardware Installation

WARNING: FAILURE TO PROVIDE PROPER VENTILATION

MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF

CLEARANCE NEXT TO THE VENTILATION HOLES FOR

ADEQUATE AIRFLOW.

Rack Mounting

1. Slide the EdgeRouter into the Mounting Bracket and secure

it using the eight Bracket Screws.

2. Attach the Mounting Bracket and EdgeRouter to the rack

using the four Mounting Screws. (If the rack has square slots,

use the Cage Nuts with the Mounting Screws.)

Wall Mounting

To mount the EdgeRouter on a wall, you will need a drill, a

6mm drill bit, and a Phillips screwdriver.

1. Use a 6 mm drill bit to drill two holes 100 mm apart.

2. Insert the Wall Mount Anchors into the holes. Use a Phillips

screwdriver to secure a Wall Mount Screw to each anchor.

Leave a clearance of approximately 3 mm between each

screw head and its anchor.

100 mm

3 mm

Note: You can also mount the EdgeRouter in a

vertical orientation.

3. Position the EdgeRouter with the Ethernet ports facing

down. Place the wall-mount slots of the EdgeRouter over

the screw heads on the wall. Then slide the EdgeRouter

down to lock it into place.

Grounding the EdgeRouter (Recommended)

The EdgeRouter is grounded through the Power Cord;

however, you can add optional ESD grounding for enhanced

ESD protection.

1. Attach the Ground Screw to secure a ground wire (not

included) to the Grounding Point.

2. Secure the other end of the ground wire to a grounding block.

Connecting Power

1. Connect the Power Cord to the Power port.

2. Connect the other end of the Power Cord to a power outlet.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Ubiquiti Router di rete

Ubiquiti

Ubiquiti TS-5-POE ToughSwitchPoE Manuale utente

Ubiquiti

Ubiquiti ER-12 Manuale utente

Ubiquiti

Ubiquiti ERLite-3 Manuale utente

Ubiquiti

Ubiquiti ERLite-3 Manuale utente

Ubiquiti

Ubiquiti ERLite-3 Manuale utente

Ubiquiti

Ubiquiti UCK-G2 Manuale utente

Ubiquiti

Ubiquiti EdgeRouter X ER-X Manuale utente

Ubiquiti

Ubiquiti airCube Manuale utente

Ubiquiti

Ubiquiti UFiber UF-WIFI Manuale di istruzioni

Ubiquiti

Ubiquiti LiteStation2 Manuale utente

Ubiquiti

Ubiquiti ToughSwitch Pro TS-80-PRO Manuale utente

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Manuale utente

Ubiquiti

Ubiquiti EdgeRouter X ER-X-SFP Manuale utente

Ubiquiti

Ubiquiti UniFi USG Manuale utente

Ubiquiti

Ubiquiti EdgeRouter 10X Manuale utente

Ubiquiti

Ubiquiti EdgeRouter LITE Manuale utente

Ubiquiti

Ubiquiti UDM Manuale utente

Ubiquiti

Ubiquiti Bullet Manuale utente

Ubiquiti

Ubiquiti ER-4 Istruzioni operative e di manutenzione

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Manuale utente

Ubiquiti

Ubiquiti EdgeRouter ER-10X Manuale utente

Ubiquiti

Ubiquiti EdgeRouter 12 Manuale utente

Ubiquiti

Ubiquiti EdgeRouter LITE Manuale utente

Ubiquiti

Ubiquiti edgerouter X SFP Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza