Ubiquiti EdgeRouter ER-8 Manuale utente

8-Port Router

Model: ER-8

Introduction

Thank you for purchasing the Ubiquiti Networks® 8-Port

EdgeRouter™. This Quick Start Guide is designed to guide you

through installation and also includes warranty terms.

Package Contents

EdgeRouter ER-8

Mounting Screws

(Qty. 4)

Cage Nuts

(Qty. 4) Power Cord

installer's responsibility to follow local country regulations, including operation within legal

frequency channels, output power, indoor cabling requirements, and Dynamic Frequency

Selection (DFS) requirements.

Installation Requirements

• Phillips screwdriver (for rack- or wall-mounting)

• Standard-sized, 19" wide rack with a minimum of 1U height

available (for rack-mounting)

• For indoor applications, use Category 5 (or above) UTP

cabling approved for indoor use.

• For outdoor applications, shielded Category 5 (or above)

cabling should be used for all wired Ethernet connections

and should be grounded through the AC ground of the

power supply.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit:

www.ubnt.com/toughcable

WARNING: To reduce the risk of fire or electric shock,

do not expose the EdgeRouter to rain or moisture.

Note: Although the cabling can be located outdoors,

the EdgeRouter itself should be housed inside a

protective enclosure.

Hardware Overview

Front Panel Ports

Console RJ45 (eth0-eth7)

USB

Interface Description

Console

RJ45 serial console port for Command

Line Interface (CLI) management. Use an

RJ45-to-DB9, serial console cable, also

known as a rollover cable, to connect the

Console port to your computer. (If your

computer does not have a DB9 port, then

you will also need a DB9 adapter.) Then

configure the following settings as needed:

• Baud rate 115200

• Data bits 8

• Parity NONE

• Stop bits 1

• Flow control NONE

USB Reserved for future use.

RJ45

(eth0-eth7)

RJ45 ports support 10/100/1000 Ethernet

connections.

Front Panel Button

Reset

Button Description

Reset

There are two methods to reset the

EdgeRouter to factory defaults:

• Runtime reset (recommended) The

EdgeRouter should be running after

bootup is complete. Press and hold

the Reset button for about 10seconds

until the right LED on RJ45 port eth7

starts flashing and then becomes

solidly lit. After a few seconds, the LED

will turn off, and the EdgeRouter will

automaticallyreboot.

• Power-on reset Disconnect the Power

Cord from the EdgeRouter. Press and hold

the Reset button while connecting the

Power Cord to the EdgeRouter. The port

LEDs will light up in sequential order.

Keep holding the Reset button until the

LED on the last port starts flashing, and

then release the button.

Front Panel LEDs

The LEDs on the left side of the RJ45 ports are not used at this

time. Below is a description of the other LEDs:

Power

Speed/Link/Act

LED State Status

RJ45 (eth0-7)

Speed/

Link/Act

Off No Link

Amber Link Established at

10/100Mbps

Amber Flashing Link Activity at

10/100Mbps

Green Link Established at

1000Mbps

Green Flashing Link Activity at

1000Mbps

Power

White 8-Port EdgeRouter is

poweredon.

Back Panel

Mounting Holes

Power

Ventilation Holes

Mounting Holes

Fans

Note: There are additional ventilation holes on the sides

of the EdgeRouter.

Hardware Installation

WARNING: FAILURE TO PROVIDE PROPER VENTILATION

MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF

CLEARANCE NEXT TO THE VENTILATION HOLES FOR

ADEQUATE AIRFLOW.

1. Attach the EdgeRouter to the rack using the four Mounting

Screws. (If the rack has square slots, then use the Cage Nuts

with the Mounting Screws.)

2. Connect the Power Cord to the Power port.

3. Connect the other end of the Power Cord to a power outlet.

Accessing the EdgeOS Configuration Interface

The EdgeOS® configuration interface can be accessed via

DHCP or static IP address assignment. By default, eth1 is set

up as a DHCP client, while eth0 is assigned a static IP address

of 192.168.1.1. To configure the EdgeRouter, proceed to the

appropriate section: DHCP or "Static IP Address".

DHCP

1. Connect an Ethernet cable from eth1 on the EdgeRouter to

a LAN segment that has an existing DHCP server.

2. To check the IP address of the EdgeRouter, use one of the

following methods:

• Set up the DHCP server to provide a specific IP address

to the EdgeRouter based on its MAC address (on the

label).

• Let the EdgeRouter obtain an IP address and then check

the DHCP server to see which IP address was assigned.

3. Launch your web browser. Enter the appropriate IP address

in the address field. Press enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username

and Password fields. Read the Ubiquiti License Agreement,

and check the box next to I agree to the terms of this License

Agreement to accept it. Click Login.

The EdgeOS Configuration Interface will appear, allowing you

to customize your settings as needed. For more information,

refer to the EdgeOS User Guide, which is available at

www.ubnt.com/download/edgemax

You can also manage your device using the Ubiquiti® Network

Management System. UNMS™lets you configure, monitor,

upgrade, and back up your devices using a single application.

Get started at www.unms.com

Static IP Address

1. Connect an Ethernet cable from the Ethernet port of your

computer to the port labeled eth0 on the EdgeRouter.

2. Configure the Ethernet adapter on your host system with a

static IP address on the 192.168.1.x subnet.

3. Launch your web browser. Type https://192.168.1.1 in the

address field. Press enter (PC) or return (Mac).

https://192.168.1.1

Altri manuali per EdgeRouter ER-8

Indice

Altri manuali Ubiquiti Router di rete

Ubiquiti

Ubiquiti EdgeRouter ER-12P Manuale utente

Ubiquiti

Ubiquiti UFiber UF-WIFI Manuale di istruzioni

Ubiquiti

Ubiquiti EdgeRouter 4 Manuale utente

Ubiquiti

Ubiquiti EdgeRouter X ER-X Manuale utente

Ubiquiti

Ubiquiti EdgeRouter X ER-X Manuale utente

Ubiquiti

Ubiquiti EdgeRouter LITE Manuale utente

Ubiquiti

Ubiquiti AiAF-5 Manuale utente

Ubiquiti

Ubiquiti ERLite-3 Manuale utente

Ubiquiti

Ubiquiti UFber UF-WIFI Manuale utente

Ubiquiti

Ubiquiti UDM Manuale utente

Ubiquiti

Ubiquiti EdgeRouter 10X Manuale utente

Ubiquiti

Ubiquiti TS-8-PRO Manuale utente

Ubiquiti

Ubiquiti airCube Manuale di istruzioni

Ubiquiti

Ubiquiti ERLite-3 Manuale utente

Ubiquiti

Ubiquiti EdgeRouter X ER-X-SFP Manuale utente

Ubiquiti

Ubiquiti EdgeRouter 6P Manuale utente

Ubiquiti

Ubiquiti UFber loco Manuale utente

Ubiquiti

Ubiquiti edgerouter X SFP Manuale utente

Ubiquiti

Ubiquiti EdgePoint R8 Manuale dell'operatore

Ubiquiti

Ubiquiti UniFi AP PRO Manuale utente

Ubiquiti

Ubiquiti EdgeRouter PoE ERPoe-5 Manuale utente

Ubiquiti

Ubiquiti EdgeRouter LITE Manuale utente

Ubiquiti

Ubiquiti UCK-G2 Manuale utente

Ubiquiti

Ubiquiti ER-8-XG Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza