Ubiquiti UniFi Cloud Key Gen2 Manuale utente
Model: UCK-G2
Introduction
Thank you for purchasing the Ubiquiti Networks®
UniFi® Cloud Key Gen2. This Quick Start Guide is
designed to guide you through installation and also
includes warrantyterms.
Package Contents
UniFi Cloud Key Gen2
System Requirements
• Mobile App: Latest version of the UniFi App
(
available on the App Store®and Google Play
™
).
• Web Browser: Latest Google Chrome browser
(Other browsers may have limited functionality.)
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the
professional installer’s responsibility to follow local country regulations,
including operation within legal frequency channels, output power, indoor
cabling requirements, and Dynamic Frequency Selection (DFS) requirements.
Network Topology Requirement
A DHCP-enabled network (for the UniFi Cloud Key to
obtain an IP address)
US-16-150W
USG-PRO-4
(DHCP Server)
Internet
UAP-AC-HD UAP-AC-PRO
LAN
WAN
UniFi Cloud Key Gen2
(UniFi Controller)
UAP-AC-M-PRO
Remote Access to
UniFi Controller
Sample Network Diagram
All UniFi devices also support off-site management
controllers. For setup details, see the User Guide on
the website at: www.ubnt.com/download/unifi
Hardware Overview
Top Panel
Color State Status
White Solid Ready for
configuration
Flashing Initializing
Heartbeat
Flashing
Firmware upgrade
in progress. Device
is busy; do not
touch or unplug it.
Blue Solid Device ready for use
Flashing Shutting down
Rapid
Flashing
Device failure; refer
to the display for
more information.
Slow
Flashing
User connected to
device
Off/White/Blue Repeating Recovery mode
Front Panel
146 745
192.168.1.1
IP Address
Network
Devices
Controller Cloud
Client
Devices
Controller SDN controller icon
IP Address Controller IP address and name
Cloud Cloud status
Network Devices Number of network devices
connected to the controller
Client Devices Number of clients/client devices
connected to the controller
Back Panel
microSD Slot
Reset Button
USB Type-C
Power Port
Ethernet Port
Power Button
Reset The Reset button serves two functions:
• Restart Press and release the Reset button quickly.
• Restore to Factory Default Settings Press and hold
the Reset button for more than five seconds.
Power Button Press to turn the Cloud Key on or off.
USB Type-C Power Connection for optional power
source (5V, minimum 1A) if PoE is not available.
microSD Slot Designed for configuration backup.
Ethernet Connects to a DHCP server on your LAN.
Power can be provided by an 802.3af PoE switch, such
as the UniFi PoE Switch.
Side Panel
Rack-Mount
Notch
Rack-Mount Notch Locks the Cloud Key into place
when using the optional rack-mount accessory (sold
separately).
Bottom Panel
Rack-Mount
Connector
(Connector shown without protective film)
Rack-Mount Connector Connects to the optional
rack-mount accessory (sold separately).
Hardware Installation
1. Connect an Ethernet cable (not included) to the
Ethernet Port.
2. Connect the other end of the Ethernet cable
to a port on a compatible PoE switch, such as a
UniFiPoE Switch.
1 3 5 7 9 11 13 15 17 19 21 22
2 4 6 8 10 12 14 16 18 20 22 24
SFP1
SFP2
Powering the UniFi Cloud Key
Use an 802.3af-compliant switch, such as a UniFi PoE
Switch, or a USB power source (not included).
UniFi Switch
The UniFi Cloud Key can be powered by a UniFi PoE
Switch or other 802.3af-compliant switch.
1 3 5 7 9 11 13 15 17 19 21 22
2 4 6 8 10 12 14 16 18 20 22 24
SFP1
SFP2
UniFi Switch Power Connection Diagram
Note: If using the optional rack-mount accessory
(sold separately), remove the protective
film from the Rack-Mount Connector before
attaching to the rack-mount.
USB Power Source
Connect the USB cable (not included) from the UniFi
Cloud Key directly to a USB power source
(5V, minimum 1A).
USB Power Connection Diagram
Software Installation
The UniFi Controller software is pre-installed on the
Cloud Key G2. Use one of the following methods to
launch the software:
• If you are using the mobile app to install the
Cloud KeyG2, follow the procedure under the
Mobile App section (recommended).
• If you are using Chrome, go to the Chrome
Instructions section.
• If you are using a different web browser, go to the
Instructions for Other Web Browsers section.
Mobile App
The UniFi app is available for free in the App Store
for iOS-based devices and Google Play store for
Android-based devices.
1. Download and launch the mobile app. Tap +to
search for a new controller.
2. When the Add Controller screen appears, tap
Set up this controller to begin the installation.
Cloud Key G2
3. Wait for the app to connect to the Cloud Key.
4. Enter a name for your controller and verify the
Country and Time Zone information and tap Next.
5. To enable cloud access, tap the toggle switch ON
and enter a username and password for the
Local Admin account. Tap Next.
Controller Admin
Controller Admin
6. When the Adopt Devices screen appears, select
the controller to adopt and tap Next.
7. To add a wireless network, tap the toggle switch
ON and proceed to step 8. To skip this step, tap
Finish and proceed to step 9.
Note: You can add or remove wireless networks at
a later time using the UniFi Controller software.
8. Create a name and password for your wireless
network. To enable Guest Access, tap the toggle
switch ON; otherwise, tap Finish.
9. Wait for the app to create your wireless network
and finish configuring the controller.
10. Once setup is complete, tap Exit Setup.
Altri manuali per UniFi Cloud Key Gen2
2
Questo manuale è adatto per i seguenti modelli
1
Indice
