Ubiquiti UAP-AC Manuale utente

Enterprise WiFi System

Model: UAP-AC Outdoor

Introduction

Thank you for purchasing the Ubiquiti Networks™UniFi™

Enterprise WiFi System. The UniFi Enterprise WiFi System

includes the UniFi Controller software, which allows you to

manage your wireless network using a web browser.

The UniFi Controller software and User Guide are available for

download at downloads.ubnt.com/unifi

This Quick Start Guide includes the warranty terms and is for

use with the UniFi AP AC Outdoor, model UAP-AC Outdoor.

The UniFi AP can be powered by any of the following:

• PoE GigE Adapter (included)

• 48V, PoE 802.3at compliant switch

• Ubiquiti Networks TOUGHSwitch PRO, model TS-8-PRO

The UniFi AP also includes the necessary hardware for

mounting the unit on a wall or a pole.

Installation Requirements

• 13 mm wrench

• Shielded Category 5 (or above) cabling should be used

for all outdoor wired Ethernet connections and should be

grounded through the AC ground of the PoE.

We recommend that you protect your networks from

brutal outdoor environments and devastating ESD

attacks with industrial-grade shielded Ethernet cable from

UbiquitiNetworks. For more details, visit

www.ubnt.com/toughcable

cable and earth grounding must be used as conditions of product warranty. TOUGHCable is

designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Package Contents

UniFi AP AC Outdoor Mounting

Bracket

Pole Clamps

(Qty. 2)

Carriage Bolts

(M8x120, Qty. 4)

Flange Nuts

(M8, Qty. 4)

Enterprise WiFi System

Model: UAP-AC-Outdoor

PoE GigE Adapter

(48V, 0.5A Gigabit)

Power Cord Quick Start

Guide

System Requirements

• Microsoft Windows Vista, Windows 7, Windows 8, or

MacOSX

• Java Runtime Environment 1.6 (or above)

• Web Browser: Mozilla Firefox, Google Chrome, or Microsoft

Internet Explorer 8 (or above)

Network Topology Requirements

• A DHCP-enabled network for the UniFi AP to obtain an

IPaddress (wireless clients will also obtain IP addresses after

deployment)

• A management station computer running the UniFi

Controller software, located either onsite and connected to

the same Layer2 network, or off-site in a cloud or NOC

Router

O-Site

Cloud/NOC

On-Site

Management Station

UAP-PRO

UAP-AC-Outdoor

UAP-AC

UAP-Outdoor

Sample Network Diagram

All UniFi APs support off-site management controllers.

For setup details, refer to the User Guide on the website:

documentation.ubnt.com/unifi

Hardware Overview

LED

LED Color Status

Flashing White Initializing.

Steady White Factory default, waiting to be integrated.

Alternating

White/Blue

Device is busy; do not touch or unplug it.

This usually indicates that a process such

as a firmware upgrade is taking place.

Quickly

Flashing Blue

This is used to locate an AP.

When you click Locate in the UniFi

Controller software, the AP will flash. It

will also display the location of the AP on

the map.

Steady Blue

Indicates the device has been successfully

integrated into a network and is working

properly.

Steady Blue

with occasional

flashing

Indicates the device is in an isolated state

(all WLANs are brought down until an

uplink is found).

*720-00046-01*

720-00046-01

Ports

Main

Ethernet Port

Reset

Button

Secondary

Ethernet Port

Secondary The Secondary port is a Gigabit Ethernet port used

for bridging.

Reset The Reset button serves two functions for the UniFi AP:

• Restart Press and release the Reset button quickly.

• Restore to Factory Default Settings Press and hold the

Reset button for more then five seconds.

Main The Main port is a Gigabit Ethernet port used to connect

the power and should be connected to the LAN and DHCP

server. Power can be provided by any of the following:

• PoE GigE adapter (included)

• 48V, 802.3at compliant switch

• Ubiquiti Networks TOUGHSwitch PRO, model TS-8-PRO

Hardware Installation

The recommended mounting of the UniFi AP AC Outdoor is

on a pole. Optionally, the UniFi AP may be installed on a wall

using additional hardware.

Pole Mount

1. Insert two Carriage Bolts into each Pole Clamp and install

the Flange Nuts as far down the bolts as necessary to

accommodate the pole.

Note: The mounting assembly can accommodate a

Ø 1.5" - 3.0" pole.

2. Attach one of the Pole Clamps to the pole by sliding the

Carriage Bolts around the pole and into the top two slots of

the Mounting Bracket.

3. Uniformly hand-tighten each Flange Nut. Ensure the Pole

Clamp is evenly clamped around the pole and tighten each

Flange Nut to approximately 25 N-m (18 lb-ft).

4. Attach the other Pole Clamp to the pole by sliding the

Carriage Bolts around the pole and into the bottom two

slots of the Mounting Bracket.

5. Uniformly hand-tighten each Flange Nut. Ensure the Pole

Clamp is evenly clamped around the pole and tighten each

Flange Nut to approximately 25 N-m (18 lb-ft).

6. Attach the UniFi AP to the Mounting Bracket:

a. Position the UniFi AP with the Mounting Bracket aligned

between the mounting tabs on the back of the UniFi AP.

b. Slide the UniFi AP downward into the grooves of the

Mounting Bracket until the snap pins engage and lock

the UniFi AP in place.

Wall Mount

To mount the UniFi AP on a wall, securely attach the Mounting

Bracket to the wall using four fasteners (not included).

Note: The Mounting Bracket must attach directly to a

stud or other structurally stable surface.

1. Locate the stud.

2. Position the Mounting Bracket on the stud, ensuring at least

two holes are centered on the stud.

3. Mark all four holes on the wall.

4. Drill pilot holes as necessary.

5. Secure the Mounting Bracket to the wall with four fasteners.

Indice

Altri manuali Ubiquiti Punto di accesso wireless

Ubiquiti

Ubiquiti LiteBeam LBE5AC120-U Manuale utente

Ubiquiti

Ubiquiti NanoStationM Series Manuale utente

Ubiquiti

Ubiquiti NanoStatonM Series Manuale utente

Ubiquiti

Ubiquiti UniFi Manuale utente

Ubiquiti

Ubiquiti UniFi UAP-IW-HD Manuale utente

Ubiquiti

Ubiquiti NBE-5AC-Gen2 Manuale utente

Ubiquiti

Ubiquiti QCA9994 Guida all'applicazione

Ubiquiti

Ubiquiti UniFi UAP-FlexHD Manuale utente

Ubiquiti

Ubiquiti NanoStation loco Manuale utente

Ubiquiti

Ubiquiti UAP-AC-IW Manuale utente

Ubiquiti

Ubiquiti PowerBeam AC PBE-5AC-300 Manuale utente

Ubiquiti

Ubiquiti UniFi Manuale utente

Ubiquiti

Ubiquiti PowerBeam AC GENZ Manuale utente

Ubiquiti

Ubiquiti airFiber AF-11 Manuale utente

Ubiquiti

Ubiquiti LiteAP ac LAP-120 Manuale utente

Ubiquiti

Ubiquiti PowerBeam ac ISO Manuale utente

Ubiquiti

Ubiquiti LiteBeam LBE-5AC-LR Manuale utente

Ubiquiti

Ubiquiti UAP-IW-HD Manuale utente

Ubiquiti

Ubiquiti UniFi Stadium XG Manuale utente

Ubiquiti

Ubiquiti UniFi Manuale utente

Ubiquiti

Ubiquiti UAP-AC-PRO-5 Manuale utente

Ubiquiti

Ubiquiti UniFi UAP-AC-LR-5-EU Manuale utente

Ubiquiti

Ubiquiti LTU-Lite Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente

Draytek

Draytek VIGORAP 902 Manuale utente

EnGenius

EnGenius EAP350 Manuale utente